Sony DSC-W510 (serv.man2) Service Manual ▷ View online
DSC-W510_ADJ
5-5
Adjustment order
Screen display
5-3-3. WB/AGC Adjustment
The WB/AGC (White Balance/Analog Gain Control) Adjustment order
is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig. 5-3-7
The adjustment is complete.
The adjustment is finished abnormally.
Fig. 5-3-8
Malfunction of WB/AGC
adjustment result
5-3-4. MeShut80 Adjustment
The MeShut80 (Mechanical Shutter 80) Adjustment order is as follows.
Note:
Perform the MeShut80 Adjustment after those performed in 5-3-2 to 5-3-3.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig. 5-3-10
The adjustment is complete.
The adjustment is finished abnormally.
Fig. 5-3-11
Malfunction of MeShut80
adjustment result
Adjustment order
Screen display
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Confirm the indication
on the screen.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-8)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “WB/AGC (LV10)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-7)
Press the “
(Playback)” button to return to
adjustment menu.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item to “WB/AGC (LV10)”,
and press the “
(Playback)” button. Press the Control button “ v ” “ V ” to change selected item
to “Light Src”, and press the Control button “ b ” “ B ” to set the value as “00002”, and press the
Control button “ z ”.
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-6)
Finished normally.
Finished abnormally.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-11)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “MeShut80 (LV14)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-10)
Press the “
(Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-9)
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item to “WB/AGC (LV10)”,
and press the “
(Playback)” button, then confirm that the value of “Light Src” is set as “00002”.
Equipment required: Small pattern box (PTB-1450)
Clear chart
Small pattern box
(PTB-1450)
5 mm
or less
Camera
Fig. 5-3-6
Equipment required: Small pattern box (PTB-1450)
Clear chart
Fig. 5-3-9
Small pattern box
(PTB-1450)
5 mm
or less
Camera
DSC-W510_ADJ
5-6
Adjustment order
Screen display
5-3-5. Dark DP Adjustment
The Dark DP (Dead Pixel) Adjustment order is as follows.
Note:
Perform the Dark DP Adjustment after those performed in 5-3-2 to 5-3-3.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig. 5-3-13
The adjustment is complete.
The adjustment is finished abnormally.
Fig. 5-3-14
Malfunction of Dark DP
adjustment result
Adjustment order
Screen display
5-3-6. Light/S.S Adjustment
The Light/S.S (Light Dead Pixel/Slow Shutter Dead Pixel)
Adjustment order is as follows.
Note:
Perform the Light/S.S Adjustment after those performed in 5-3-2 to 5-3-3.
The adjustment is finished normally.
Fig. 5-3-17
The adjustment is complete.
The adjustment is finished abnormally.
Fig. 5-3-18
Malfunction of Light
adjustment result
Fig. 5-3-19
Malfunction of S.S
adjustment result
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-14)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “Dark DPC (LV10)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-13)
Press the “
(Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-12)
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-18, 5-3-19)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “Light S.S (BLACK)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
*1 If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
*2 It takes approximately 15 minutes or more on this adjustment.
In case of the adjustment
is finished normally, the
adjustment completion
indication appears on the
screen. (Fig. 5-3-17)
* The Self-timer lamp
lights up. (Fig. 5-3-16)
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (All black) (Fig. 5-3-15)
Restart the camera.
Self-timer lamp
Fig. 5-3-16
Equipment required: Small pattern box (PTB-1450)
Clear chart
Fig. 5-3-12
Small pattern box
(PTB-1450)
5 mm
or less
Camera
Fig. 5-3-15
Camera
Equipment required: Cover camera lens
(All black)
Black cloth
DSC-W510_ADJ
5-7
5-3-7. Flash WB Adjustment
Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as shown below.
1) Provide woody board A, B, C and D of 15 mm thickness.
2) Apply black mat paint to one side of woody board A, B and D.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side of woody board A, B, C and D are internal. (Fig. 5-3-21)
Adjustment order
Screen display
The adjustment is finished normally.
The adjustment is finished normally.
Fig. 5-3-22
The adjustment is complete.
The adjustment is finished abnormally.
Fig. 5-3-23
Malfunction of Flash WB
adjustment
The Flash WB Adjustment order is as follows.
Note:
Perform the Flash WB Adjustment after those performed in 5-3-2 to 5-3-3.
Woody board A (2)
400 mm
Woody board B (2)
370 mm
Woody board C (1)
700 mm
513 mm
513 mm
700 mm
Woody board D (1)
370 mm
370 mm
700 mm
730 mm
100 mm
120 mm
Fig. 5-3-20
Woody board A
Woody board B
Woody board B
Woody board C
Woody board A
Woody board D
Front of the lens
L = 500 mm
L
Camera
Fig. 5-3-21
Confirm the indication
on the screen.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-23)
In this case, confirm the adjusting environment
and readjust.
n
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “FLASH WB”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-22)
Press the “
(Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flash Adjustment Box. (Fig. 5-3-21)
Finished normally.
Finished abnormally.
DSC-W510_ADJ
5-8
5-3-8. Lens Option
Lens Option Setting order is as follows.
1)
Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
2) Press the Control button “ b ” “ B ” and “ v ” “ V ”to change selected item. Choose “Lens Option”,
press the “ (Playback)” button to choose item.
Note:
If the setting is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the setting. (Page 5-3)
3) Press the Control button “ V ” to “Enable LDC” item after press the Control button “ B ” to set enable (00001).
Press the Control button “ V ” to “Enable LSC” item after press the Control button “ B ” to set enable (00001).
Final Press the “ (Playback)” button to return to adjustment mode, then press the Control button “ z ”,
select “OK” and press the Control button “ z ” to start.
Note:
LDC : Lens Distortion Correction
LSC : Lens Shading Correction
4) Confirm the indication on the screen.
When the setting is finished, the setting completion indication appears on the screen. (Fig. 5-3-24)
Press the “ (Playback)” button to return to adjustment menu.
5-3-9. Set Language Destination
Note:
Finish all of the adjustment except for the Language Destination setting.
Once the Language Destination setting is finished, it cannot be reset.
USB Driver and Service Tool
Put the two folders “USB Driver” and “Service Tool” downloaded in “5-1-5. Setting the Adjustment Mode” (Page 5-3) in any place of the PC.
The procedure of installing a USB Driver is as follows.
1) Connect the camera started up with the Adjustment mode, and the PC with a Dedicated USB Cable.
2) Install the USB Driver according to the guidance on the screen.
Connecting USB to PC
Connect the equipment as shown below. (Fig. 5-3-25)
Starting up the Service Tool
Double click the “ServiceTool_Ver[][][].exe” in the “Service Tool” folder to start up the Service Tool. (Fig. 5-3-26)
Dedicated USB Cable
Personal Computer
1 To a USB jack of the PC
2 To the
(USB)/A/V OUT
jack
jack
Fig. 5-3-25
Fig. 5-3-24
Fig. 5-3-26
Click on the first or last page to see other DSC-W510 (serv.man2) service manuals if exist.