Sony DSC-W370 Service Manual ▷ View online
DSC-W370
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
View Position
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “*” are not stocked since they are seldom required for routine service. Some
delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts speci-
fied in the diagrams or the components used on the set.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
When indicating parts by reference
number,please include the board name.
• Abbreviation
AUS : Australian model
CND : Canadian model
Top View
Back View
Right View
Bottom View
Front View
Left View
ACCESSORIES
Link
ACCESSORIES
ASSEMBLY
DISCHARGING OF THE CHARGING CAPACITOR
1
Rear Cabinet Assy
2
Front Cabinet Assy
3
Top Cover Assy
5
SW Board
6
LCD Bracket
7
LCD Module
8
Strobe Unit
9
Main Board
0
Lens Assy
qa
Main Frame Assy
DSC-W370
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is pos-
sible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap
W
W
insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Wrap insulating tape.
R:1 k /1 W
(Part code: 1-215-869-11)
(Part code: 1-215-869-11)
Strobe Unit
Note:
Note:
High-voltage cautions
High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
DSC-W370
2-3
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
X-2547-193-1 CABINET ASSY, FRONT (SILVER)
1
X-2547-194-1 CABINET ASSY, FRONT (BLACK)
1
X-2547-195-1 CABINET ASSY, FRONT (GREEN)
1
X-2547-196-1 CABINET ASSY, FRONT (RED)
*
2
4-179-228-01 DC DOOR
*
3
4-179-234-01 STRAP PIN
4
4-179-230-01 JACK COVER
5
X-2547-197-1 TOP COVER ASSY
6
X-2547-189-1 CABINET ASSY, REAR (SILVER)
6
X-2547-190-1 CABINET ASSY, REAR (BLACK)
6
X-2547-191-1 CABINET ASSY, REAR (GREEN)
6
X-2547-192-1 CABINET ASSY, REAR (RED)
*
7
4-179-229-01 DECORATION PARTS
#S1
4-179-226-01 MACHINE_M1.7_3_BLK_AB
#S2
4-179-227-01 MACHINE_M1.7_2.5_BLK_AB
#S3
4-179-231-01 MACHINE_M1.4_2_SVR_AB
1. Remove to numerical order (
1
to 4
) in the left figure.
DISASSEMBLY
2
#S1 X 2
1
#S1 X 2 → #S2 X 2 → #S1 X 2
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
3
#S3 X 1
DISCHARGING OF THE CHARGING CAPACITOR
4
Left View
Bottom View
Right View
#S1
#S2
#S1
Bottom View
#S1
Top View
#S3
4
2�
1
2
4
3�
5
1�
6
7
#S1
#S3
#S1
#S2
#S1
3
LCD Section
(See Page 2-4)
(See Page 2-4)
1(Claw)
2(Claw)
3(Claw)
DSC-W370
2-4
2-1-2. LCD SECTION
1. Remove to numerical order (
5
to
7
) in the left figure.
DISASSEMBLY
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
*
51
4-179-236-01 LCD BRACKET
52
4-179-233-01 SW BOARD
53
X-2547-198-1 MODE DIAL ASSY
54
4-179-237-01 LCD MODULE
*
55
4-179-235-01 TRIPOD SCREW
#S3
4-179-231-01 MACHINE_M1.4_2_SVR_AB
#S4
4-179-232-01 TAPPING_M1.4_3.5_SVR_AB
5
#S3 X 1
6
LCD Module Raise (
6
) → #S4 X 3
Back View
#S3
Back View
#S4
LCD Module
6
5�
52
53
7�
54
6�
51
55
#S3
#S4
#S3
Main Frame Section
(See Page 2-5)
(See Page 2-5)
Click on the first or last page to see other DSC-W370 service manuals if exist.