Sony DSC-W350 (serv.man2) Service Manual ▷ View online
DSC-W350_L2
2-2
AF-125フレキシブル基板のストロボ用充電コンデンサ
(C901)は最大315Vの電圧で充電されています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
The charging capacitor (C901) of the AF-125 flexible board is
charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
DISCHARGING OF THE CHARGING CAPACITOR (C901)
ストロボ用充電コンデンサ(C901)の放電
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
Short-circuit between two points
with the short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:: 1-215-869-11)
C901
Rear Side
Front Side
AF-125 Flexible
Board
Board
後ろ側
前側
C901
AF-125 Flexible
Board
Board
コンデンサの放電
Note: 高電圧の警告
フラッシュユニットの電源コンデンサ
の端子間をショート治具で約10秒間
接続する。
の端子間をショート治具で約10秒間
接続する。
R:1 k
Ω
/1 W
(部品コード:1-215-869-11)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
先端の剥がれたメッキ部はカットして
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
除去してください。
(メッキ破片がコネクタ内に残っている
場合もあるので注意してください)
Wrap insulating tape.
絶縁テープで巻く
DSC-W350_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 1
4-167-575-01
FRAME (640), MAIN (Note 4)
* 2
3-289-764-01 GASKET
(280)
* 3
4-167-576-01
SHEET (640), SY INSULATING
4
4-168-186-01
SHEET (670), LCD INSULATING
5 4-168-183-
02
CUSHION (670), LCD (Note 2)
6
4-168-182-01
WINDOW (670), LCD (Note 2)
7
1-880-209-11
FPC-019 FLEXIBLE BOARD
8
A-1731-539-A SW-562 BOARD, COMPLETE
9
X-2541-645-1 CABINET (REAR) ASSY (640C) (Note 3)
LCD901 1-802-984-11
LCD MODULE (LMS270GF07)
#156 2-635-591-61
SCREW (M1.4), NEW TRUSTAR P2 (Note 1)
#159 2-662-396-51
SCREW (M1.4), NEW, TRUSTAR, P2 (Note 1)
1. Remove to numerical order (
1
to
4
) in the left figure.
DISASSEMBLY
1
#156 / #159 X 6
Screw
#156: M1.4 X 4.0
(Silver)
2-635-591-61
2-635-591-61
4.0
1.4
3
2
8
3
LCD901
4
1
(Note 4)
2
5
(Note 2)
6
(Note 2)
Front/Top Section
(See page 2-4)
(See page 2-4)
7
4
1
9
(Note 3)
2
(Hole)
#156
#159
(Note 1)
#159
(Note 1)
#156
#159
(Note 1)
#159
(Note 1)
#156
#159
(Note 1)
#159
(Note 1)
Bottom View
Left View
Right View
#156
#159
#156
#159
#156
#159
4.0
1.4
#159: M1.4 X 4.0
(Black)
2-662-396-51
2-662-396-51
Note
Note 2: Refer to “Assembly-6: Attaching Method
of LCD cushion (670) and LCD window
(670)”.
(670)”.
Note 2: Assembly-6: Attaching Method of LCD
cushion (670) and LCD window (670) を
参照してください。
参照してください。
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#156 (Silver)
SILVER/PINK/GOLD
#159 (Black)
BLACK/BLUE
Cabinet's Color
Table 2-1
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Note 3: Refer to “Assembly-5: Precaution During
Cabinet (Rear) Assy Installation”.
Note 3: Assembly-5: Precaution During Cabinet
(Rear) Assy Installation を参照してくだ
さい。
さい。
Note 4: Refer to “Assembly-4: Precaution During
Main Frame Installation”.
Note 4: Assembly-4: Precaution During Main
Frame Installation を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
DSC-W350_L2
2-4
2-1-2. FRONT/TOP SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2541-632-1 CABINET (FRONT) ASSY (640C) (SILVER)
51
X-2541-633-1 CABINET (FRONT) ASSY (640D) (BLACK)
51
X-2541-634-1 CABINET (FRONT) ASSY (640E) (PINK)
51
X-2541-635-1 CABINET (FRONT) ASSY (640F) (GOLD)
51
X-2541-636-1 CABINET (FRONT) ASSY (640G) (BLUE)
52 4-111-391-01 HOLDER,
MICROPHONE
53
A-1731-544-A SP-052 BOARD, COMPLETE (Note 2)
* 54 4-167-574-01 SCREW
(640),
TRIPOD
55
4-167-564-01
LIGHT (640), MS GUIDE,
* 56 4-168-315-01 TAPE
(N5)
57
1-880-206-11
FPC-016 FLEXIBLE BOARD
0 58
1-487-586-11 FLASH
UNIT
59
A-1731-542-A ST-225 BOARD, COMPLETE
60
X-2541-639-1 CABINET (UPPER) ASSY (640C) (SILVER)
60
X-2541-640-1 CABINET (UPPER) ASSY (640D) (BLACK)
60
X-2541-641-1 CABINET (UPPER) ASSY (640E) (PINK)
60
X-2541-642-1 CABINET (UPPER) ASSY (640F) (GOLD)
60
X-2541-643-1 CABINET (UPPER) ASSY (640G) (BLUE)
0 BT900 1-756-710-12
LITHIUM RECHARGEABLE BATTERY
SP901
1-858-302-11 LOUDSPEAKER
(0.8CM)
#156 2-635-591-61
SCREW (M1.4), NEW TRUSTAR P2 (Note 1)
#159 2-662-396-51
SCREW (M1.4), NEW, TRUSTAR, P2 (Note 1)
#156
#159
(Note 1)
#159
(Note 1)
56
9
: BT900 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page
Board on the mount position.
(See page
6-5
)
Main Section
(See page 2-5)
(See page 2-5)
9
60
q;
59
5
51
SP901
BT900
7
53
(Note 2)
8
54
6
52
55
58
57
DISCHARGING OF THE CHARGING CAPACITOR
ストロボ用充電コンデンサの放電
1. Remove to numerical order (
5
to
0
) in the left figure.
DISASSEMBLY
6
Note
5
#156 / #159 X 1
9
Tape (N5) (
9
)
Screw
#156: M1.4 X 4.0
(Silver)
2-635-591-61
2-635-591-61
4.0
1.4
4.0
1.4
#159: M1.4 X 4.0
(Black)
2-662-396-51
2-662-396-51
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#156 (Silver)
SILVER/PINK/GOLD
#159 (Black)
BLACK/BLUE
Cabinet's Color
Table 2-1
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
For the combination of cabinet's color and screw, please refer to Table 2-1.
注意 :
電池の交換は、正しく行わないと破裂する恐れが
あります。電池を交換する場合には必ず同じ型名
の電池又は同等品を交換してください。
電池の交換は、正しく行わないと破裂する恐れが
あります。電池を交換する場合には必ず同じ型名
の電池又は同等品を交換してください。
使用済み電池は,取扱指示に従って処分してくだ
さい。
さい。
Caution :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instruc-
tions.
tions.
Note 2: Refer to “Assembly-3: Precaution During
SP-052 Board Installation”.
Note 2: Assembly-3: Precaution During SP-052
Board Installation を参照してください。
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
#156
#159
Bottom View
DSC-W350_L2
2-5
2-1-3. MAIN SECTION
SY
-242
BT901
(Note 2)
(Note 2)
BT902
(Note 2)
(Note 2)
BT903
(Note 2)
(Note 2)
C901
qg
101
qd
Lens Block Section
(See page 2-6)
qf
104
qa
111
qs
110
-14
107
108
109
105
#173
102
103
(Note 1)
106
qf
1. Remove to numerical order (
qa
to
qg
) in the left figure.
2. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
qf
#173 X 1 → LCD REINFORCEMENT SHEET (
qf
)
Screw
#173: M1.4 X 2.0
(Silver)
4-167-570-01
4-167-570-01
2.0
1.4
#173
Back View
Note
Note 1: Assembly-2: Insulating Sheet (670) Putting Position
を参照してください。
Note 2: Assembly-1: Installation Method of Battery Terminal
Board を参照してください。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
X-2541-625-1 CABINET ASSY (640C), CENTER (SILVER)
101
X-2541-626-1 CABINET ASSY (640D), CENTER (BLACK)
101
X-2541-627-1 CABINET ASSY (640E), CENTER (PINK)
101
X-2541-628-1 CABINET ASSY (640F), CENTER (GOLD)
101
X-2541-629-1 CABINET ASSY (640G), CENTER (BLUE)
102
4-167-571-01
SHEET, MULTI RADIATION
103
4-168-198-01
INSULATING SHEET (670) (Note 1)
104
A-1752-374-A SY-242 BOARD, COMPLETE (SERVICE)
* 105
4-167-589-01
SHEET, SY RADIATION
* 106
4-172-609-01
SHEET, LCD REINFORCEMENT
* 107 3-289-764-01 GASKET
(280)
108
4-172-234-01
TAPE (4X23), DOUBLE STICK
* 109 4-167-565-01 TAPE
(AF)
110
A-1731-548-A AF-125 FLEXIBLE BOARD, COMPLETE
* 111
4-167-573-01
RETAINER (640), CAPACITOR
0*BT901 1-780-835-11
TERMINAL BOARD BATTERY (Note 2)
0*BT902 1-780-835-11
TERMINAL BOARD BATTERY (Note 2)
0*BT903 1-780-835-11
TERMINAL BOARD BATTERY (Note 2)
0 C901 1-116-439-11
CAP, ELECT 56uF 315V
#173 4-167-570-01
SCREW (M1.4 (ECOLOGY)), 2 MAIN
Note 1: Refer to “Assembly-2: Insulating Sheet (670) Putting
Position”.
Note 2: Refer to “Assembly-1: Installation Method of Battery
Terminal Board”.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2010.02
Click on the first or last page to see other DSC-W350 (serv.man2) service manuals if exist.