DOWNLOAD Sony DSC-W330 (serv.man2) Service Manual ↓ Size: 5.84 MB | Pages: 29 in PDF or view online for FREE

Model
DSC-W330 (serv.man2)
Pages
29
Size
5.84 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-w330-sm2.pdf
Date

Sony DSC-W330 (serv.man2) Service Manual ▷ View online

DSC-W330_L2
1-7
qs
Match three ditches of the Fixed Stationaly Tube Block to three convex parts of the Straight Tube Lubcated Assy and install it.
qd
Install the Naruto Gear on the Fixed Stationaly Tube Block.
qg
Pass the Flexible Board through the hole of the Fixed Stationaly Tube.
qf
Rotate the Naruto Gear and the lens is drawn out.
qh
Rotate the Naruto Gear and the lens is
retractile
.
Eyepiece Side View
Straight Tube
Lubricated Assy
Fixed Stationaly Tube Block
Fixed Stationaly
Tube Block
Fixed Stationaly
Tube Block
Ditches
Convex Parts
Flexible Board
Fixed Stationaly Tube
Naruto Gear
Naruto Gear
Lubricated Assy
qj
Install the Warm B Lubricated Assy.
qk
Connect the Iris Flexible Board from connector of 2 Frame Assy.
w;
Install the 3 Group Frame.
ql
Install the 3 Group Spring.
wa
Install the Rear Mirror Plate with the four screws in the order of nambers.
* Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)
Warm B
Lubricated Assy
Screw
Screw
Screw
Screw
Rear Mirror Plate
3 Group Frame
3 Group
Spring
3 Group Frame
3 Group Spring
4
1
2
3
Iris Flexible Board
Flexible Board
of 2 Frame Assy
ws
Perform the Flange Back Adjustment after the assembling.
The changed portions from
Ver. 1.3 are shown in blue.
Ver. 1.4 2010.08
DSC-W330_L2
1-8E
1-11. FINAL INSPECTION
1-11-1.Confirm There Is No Fault In Actual Motion/Actual Screen
Inspect it as follows when you exchange parts in the lens block.
1
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
5
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Lens at WIDE end
Upward
Downward
Horizontal
Full stroke check
1-11-2.  Inspection When Cam Tube Block Assy Or Straight Tube Lubricated Assy Is Replaced
Focus check
1
 Preparation
 
•  Camera installed re-assemble lens.
 
•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)
 • 
Tripod
 
•  Mirror (ex. CD)
 • 
Memory 
card
 • 
PC
2
 Shoot setting
(1)  Paste the chart.
•  Chart should be on the flat wall.
•  Illuminance level in the chart should be the same.
•  Make the tripod’s height and the center of the chart to the same height.
•  Enough space needed for shooting.
(2)  Set the camera.
• Set [P] mode
• Set [Maximum] size
•  Set ISO lowest level
•  Set Steady Shot [OFF]
• Set Flash [OFF]
(3)  Set the camera on a tripod.
(4)  Adjust the position of the camera and the chart.
1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
  * The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
  * Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
  Remove the mirror.
3
 Shooting
(1) Set [Self-Timer]
(2) Shot
4
  Check the shot image.
(1)  Check the shot image on PC.
  100% Display (Display at the same magnification of its Pixel.)
  Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
<Reference>
• 
How to Print the Chart
 
Print “Forcus-Chart_A3.pdf” with printer.
 
Print at the same magnification (It means 100 % size).
 
Check the settings of printer to print in proper size.
• 
Check of chart size.
 
Make charts together and check if the size of charts is the following size.
 
* The chart consists of 2 pcs.
DSC-W330_L2
2-1
2. REPAIR  PARTS  LIST
Follow the disassembly in the numerical order given.
AC-
DIS-
IDENTIFYING  PARTS
Link
ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR
• Abbreviation
  AR  
: Argentine model
  AUS   : Australian model
  BR  
: Brazilian model
  CND   : Canadian model
  HK   : Hong Kong model
  J  
: Japanese model
  JE  
: Tourist model
  KR  
: Korea model
ASSEMBLY
SY
-243
qd 
SY-243 Board
ST-226 Board
qf 
Center Cabinet Assy
qa 
Charging Capacitor
     (MA-465 Flexible Board)
Side Cabinet (R)
q; 
Capacitor Retainer
Rear Cabinet Assy
LCD Module
Main Frame
SW-563 Board
Front Cabinet Assy
qs 
Lens Block Section
 
[Disassembly]
 [Exploded 
View]
 
• CD-774 Flexible Board
Upper Cabinet Assy
 
(ENGLISH)
NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 
one.
•  Items marked “*” are not stocked since they are seldom required for routine service. 
Some delay should be anticipated when ordering these items.
•  The mechanical parts with no reference number in the exploded views are not sup-
plied.
•  Due to standardization, replacements in the parts list may be different from the parts 
specified in the diagrams or the components used on the set.
• CAPACITORS:
 uF: 
μF
• COILS
 uH: 
μH
• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 
nonflammable
• SEMICONDUCTORS
  In each case, u: 
μ, for example:
 uA...: 
μA... , uPA... , μPA... ,
 uPB... 
μPB... , μPC... , μPC... ,
 uPD..., 
μPD...
•  Color Indication of Appearance Parts
 Example:
 
(SILVER) : Cabinet’s Color
 
(Silver) 
: Parts Color
The components identified by mark 
or dotted line with mark 
0 are critical for 
safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant 
le numéro spécifié.
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Caution
Danger of explosion if battery is incorrectly 
replaced.
Replace only with the same or equivalent 
type.
Dispose of used batteries according to 
the instructions.
DSC-W330_L2
2-2
The charging capacitor (C901) of the MA-465 flexible board is 
charged up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the 
capacitor is handled by hand.  The electric shock is caused by the 
charged voltage which is kept without discharging when the main 
power of the unit is simply turned off.  Therefore, the remaining 
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of 
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.
NOTE  FOR  REPAIR
•  Make sure that the flat cable and flexible board are not cracked 
of bent at the terminal.
  Do not insert the cable insufficiently nor crookedly.
•  When remove a connector, don’t pull at wire of connector. It is 
possible that a wire is snapped.
•  When installing a connector, don’t press down at wire of con-
nector. 
  It is possible that a wire is snapped.
•  Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING  CAPACITOR (C901)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points 
with the short jig about 10 seconds.
R:1 k
Ω/1W
(Part code:1-215-869-11)
C901
MA-465 Flexible
Board
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Wrap insulating tape.
Page of 29
Display

Click on the first or last page to see other DSC-W330 (serv.man2) service manuals if exist.