DOWNLOAD Sony DSC-W330 (serv.man2) Service Manual ↓ Size: 5.84 MB | Pages: 29 in PDF or view online for FREE

DSC-W330_L2

1-5

6

Rotate the Naruto Gear and the lens is drawn out.

8

Rotate the Naruto Gear and the lens is

retractile

.

7

Pass the Flexible Board through the hole of the Fixed Stationaly Tube.

9

Remove the Naruto Gear.

q;

Remove the Fixed Stationaly Tube Block.

qa

Remove the 2 Group Assy.

Flexible Board

Fixed Stationaly Tube

Naruto Gear

Naruto Gear
Lubricated Assy

Fixed Stationaly Tube Block

2 Group Assy

qs

Remove the 1 Group Assy.

qd

Rotate (about 120 degree) Straight Tube Lubcated Assy and align the two points of ditchies of the Straight Tube Lubricated Assy with
ditchies of the Cam Tube Block Assy, then remove the Straight Tube Lubricated Assy from the Cam Tube BlockAssy.

qf

Pour a solvent such as alcohol from two places.

qg

Remove while turning the Ornamental Ring A right and left.

qh

Remove Barrier Assy by disengaging four claws.

qj

Remove the bond at the three points.

qk

Rotate 1 Group Lens Assy and remove it from the 1 Group Frame.

A

Tweezers

1 Group Assy

Straight Tube
Lubricated Assy

Straight Tube
Lubricated Assy

Cam Tube Block Assy

Ditchies

Eyepiece Side View

120

Barrier Assy

Claws

Claws

1 Group Lens Assy

1 Group Frame

Bond

Ornamental Ring A

Solvent

The changed portions from
Ver. 1.3 are shown in blue.

DSC-W330_L2

1-6

1

Install the 1 Group Lens Assy to the 1 Group Frame.

2

Rotate the 1 Group Lens Assy and align trianglar sign with round sign.

3

Apply the bond at the three points.
Note: Use the Super X or the equivalent

6

Peel off release papers of Barrier Tapes.

7

Install Ornamental Ring A and press it lightly.

4

Affix two Barrier Tapes to Barrier Assy.
Note: The tape must not be wrinkled.

5

With four claws fitted in position, install the Barrier Assy.

Barrier Assy

Barrier Tape

Barrier Tape

Barrier Tapes

Objective Side View

1 Group Lens Assy

1 Group Frame

1 Group Lens Assy

Bond

Round sign

Triangular sign

Barrier Assy

Claws

Claws

Ornamental Ring A

Barrier
Lever

Hole

8

Install the Straight Tube Lubricated to the Cam Tube Block Assy.

9

Rotate (about 120 degree) Straight Tube Lubcated Assy and align two points of ditches of the Straight Tube Lubricated Assy with
ditches of the Cam Tube BlockAssy.

q;

Match three ledges of the 1 Group Assy to three ditshes of the Cam Tube Block Assy and install it.

qa

Match three ledges of the 2 Group Assy to three ditshes of the Straight Tube Lubcated Assy and install it.

1 Group Assy

1 Group Assy

Straight Tube
Lubricated Assy

Straight Tube
Lubricated Assy

Straight Tube
Lubricated Assy

Cam Tube Block Assy

120

Cam Tube
Block Assy

Cam Tube
Block Assy

Eyepiece Side View

Eyepiece Side View

Eyepiece Side View

Ditchies

Ditches

Ditches

Ditches

Ditches

Ledges

Ledges

2 Group Assy

2 Group Assy

DSC-W330_L2

1-7

qs

Match three ditches of the Fixed Stationaly Tube Block to three convex parts of the Straight Tube Lubcated Assy and install it.

qd

Install the Naruto Gear on the Fixed Stationaly Tube Block.

qg

Pass the Flexible Board through the hole of the Fixed Stationaly Tube.

qf

Rotate the Naruto Gear and the lens is drawn out.

qh

Rotate the Naruto Gear and the lens is

retractile

.

Eyepiece Side View

Straight Tube
Lubricated Assy

Fixed Stationaly Tube Block

Fixed Stationaly
Tube Block

Fixed Stationaly
Tube Block

Ditches

Convex Parts

Flexible Board

Fixed Stationaly Tube

Naruto Gear

Naruto Gear
Lubricated Assy

qj

Install the Warm B Lubricated Assy.

qk

Connect the Iris Flexible Board from connector of 2 Frame Assy.

w;

Install the 3 Group Frame.

ql

Install the 3 Group Spring.

wa

Install the Rear Mirror Plate with the four screws in the order of nambers.

* Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)

Warm B
Lubricated Assy

Screw

Screw

Screw

Screw

Rear Mirror Plate

3 Group Frame

3 Group
Spring

3 Group Frame

3 Group Spring

4

1

2

3

Iris Flexible Board

Flexible Board
of 2 Frame Assy

ws

Perform the Flange Back Adjustment after the assembling.

The changed portions from
Ver. 1.3 are shown in blue.

DSC-W330_L2

1-8E

Inspect it as follows when you exchange parts in the lens block.
1

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.

2

Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.

3

Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.

4

Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.

5

Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

Focus check
1

 Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

 Shoot setting

(1)  Paste the chart.

•  Chart should be on the flat wall.
•  Illuminance level in the chart should be the same.
•  Make the tripod’s height and the center of the chart to the same height.
•  Enough space needed for shooting.

(2)  Set the camera.

• Set [P] mode
• Set [Maximum] size
•  Set ISO lowest level
•  Set Steady Shot [OFF]
• Set Flash [OFF]

(3)  Set the camera on a tripod.
(4)  Adjust the position of the camera and the chart.

1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
  * The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
  * Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
  Remove the mirror.

3

 Shooting

(1) Set [Self-Timer]
(2) Shot

4

  Check the shot image.

(1)  Check the shot image on PC.
  100% Display (Display at the same magnification of its Pixel.)
  Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.

 

Print “Forcus-Chart_A3.pdf” with printer.

 

Print at the same magnification (It means 100 % size).

 

Check the settings of printer to print in proper size.

 

Make charts together and check if the size of charts is the following size.

 

* The chart consists of 2 pcs.