DOWNLOAD Sony DSC-V3 (serv.man2) Service Manual ↓ Size: 10.27 MB | Pages: 57 in PDF or view online for FREE

Model
DSC-V3 (serv.man2)
Pages
57
Size
10.27 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL 2
File
dsc-v3-sm2.pdf
Date

Sony DSC-V3 (serv.man2) Service Manual ▷ View online

SERVICE MANUAL
LEVEL
 
2
Link
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
SERVICE NOTE
DISASSEMBLY
BLOCK DIAGRAMS
FRAME SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAMS
PRINTED WIRING BOARDS
REPAIR PARTS LIST
SPECIFICATIONS
Link
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
Sony EMCS Co.
DSC-V3
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-762-51).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-762-41).
• Reference No. search on printed wiring boards is available.
• Note in Lens Frame Installation
• Note on Handling the Laser Diode
• The Method of Attachment of Harnesses
• HELP: Sheet attachment positions and procedures of processing the FLEXIBLE boards/harnesses are shown.
Ver 1.5  2006.11
DIGITAL STILL CAMERA
On the CH-146, SY-106 and DD-217 boards
This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
CH-146, SY-106 and DD-217 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-146, SY-106 and DD-217 boards are not shown.
The following pages are not shown.
Schematic diagrams .................. Pages 4-9 to 4-34
Printed wiring boards ................ Pages 4-55 to 4-60
Waveforms ................................ Pages 4-69 and 4-70
Mounted parts location .............. Pages 4-72 and 4-73
Electrical parts list ..................... Pages 5-10 to 5-12 and 5-15 to 5-18
The above-described information is shown in service manual Level 3.
DSC-V3
2006K0500-1
  © 2006.11
Published by Kohda TEC
9-876-762-32
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
— 2 —
DSC-V3
SPECIFICATIONS
x
 Camera
[System]
Image device
9.04 mm (1/1.8 type) color CCD
Primary color fi lter
Total pixels number of camera
Approx. 7 410 000 pixels
Effective pixels number of camera
Approx. 7 201 000 pixels
Lens
Carl Zeiss Vario-Sonnar
4
× zoom lens 
f = 7 
− 28 mm (34 − 136 mm when 
converted to a 35 mm still camera) 
F2.8 
− 4.0
Exposure control
Automatic exposure, Shutter speed 
priority, Aperture priority, Manual 
exposure, Scene selection (7 modes)
White balance
Automatic, Daylight, Cloudy, 
Fluorescent, Incandescent, Flash, 
One-push
File format (DCF compliant)
Still images: Exif Ver. 2.2 JPEG 
compliant, RAW, TIFF, DPOF 
compatible
Movies: MPEG1 compliant 
(Monaural)
Recording media
“Memory Stick”
CompactFlash (Type I)
Flash
Recommended distance (ISO set to 
Auto):
0.4 to 3 m (15 3/4 inches to 118 1/8 
inches) (W)
0.4 to 2.5 m (15 3/4 inches to 98 1/2 
inches) (T)
[Input and Output connectors]
A/V OUT (MONO) jack (Monaural)
Minijack
Video: 1 Vp-p, 75 
Ω, unbalanced, 
sync negative
Audio: 327 mV (at a 47 k
Ω load)
Output impedance 2.2 k
Accessory jack
Mini-minijack (
φ 2.5 mm)
USB jack 
mini-B
USB communication
Hi-Speed USB (USB 2.0 compliant) 
[LCD screen]
LCD panel
6.2 cm (2.5 type) TFT drive
Total number of dots
123 000 dots
[Power, general]
Used battery pack
NP-FR1
Power requirements
3.6 V
Power consumption (during shooting 
with LCD screen on)
1.53 W 
Operating temperature
0
°C to +40°C (+32°F to +104°F)
Storage temperature
−20°C to +60°C (−4°F to +140°F)
Dimensions
119.8
×72.0×63 mm (4 3/4×2 7/8×2 
1/2 inches) (W/H/D, excluding 
maximum protrusions)
Mass
410 g (14.5 oz) (including battery 
pack NP-FR1, “Memory Stick” and 
shoulder strap)
Microphone
Electret condenser microphone
Speaker
Dynamic speaker
Exif Print 
Compatible
PRINT Image Matching II
Compatible
PictBridge
Compatible
x
 AC-LS5/LS5B AC Adaptor
Input rating
100 V to 240 V AC, 50/60 Hz, 11 W, 
0.16 A to 0.09 A
Output rating
4.2 V DC, 1.5 A
Operating temperature 
0
°C to +40°C (+32°F to +104°F) 
Storage temperature 
−20°C to +60°C (−4°F to +140°F) 
Dimensions
Approx. 48
×29×81 mm (1 15/16×1 
3/16
×3 1/4 inches) (W/H/D, 
excluding projecting parts)
Mass
Approx. 130 g (5 oz) excluding 
power cord (mains lead) 
x
 NP-FR1 battery pack 
Used battery 
Lithium-ion battery 
Maximum voltage 
DC 4.2 V 
Nominal voltage 
DC 3.6 V
Capacity
4.4 Wh (1220 mAh) 
x
 Accessories
 
• AC-LS5/LS5B AC Adaptor (1) 
• Power cord (mains lead) (1)
• NP-FR1 battery pack (1)
• Battery case (1)
• USB cable (1)
• A/V connecting cable (1)
• Shoulder strap (1)
• CD-ROM (USB driver SPVD-012) (1)
• CD-ROM (Image Data Converter Ver.2.0) (1)
• Operating instructions (1) 
Design and specifi cations are subject to change 
without notice.
See page 5-19
— 3 —
DSC-V3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
FLEXIBLE Circuit Board Repairing
• Keep the temperature of the soldering iron around 270
°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
CAUTION
Use of controls or adjustments or performance
procedures other than those specified herein may
result in hazardous radiation exposure.
— 4 —
DSC-V3
TABLE OF CONTENTS
1.
SERVICE NOTE
1-1.
Note for Repair ································································ 1-1
1-2.
Discharging of the Charging Capacitor (C205) ··············· 1-1
1-3.
Note in Lens Frame Installation ······································ 1-2
1-4.
Notes on Handling the Laser Diode
[Laser Unit (D109) on the AF-008 FLEXIBLE
BOARD] ·········································································· 1-2
1-5.
Description on Self-diagnosis Display ···························· 1-3
2.
DISASSEMBLY
2-1.
Disassembly ····································································· 2-1
2-2.
Service Position ······························································· 2-5
2-3.
The Method of Attachment of Harnesses ························ 2-7
2-4.
Circuit Boards Location ·················································· 2-8
3.
BLOCK DIAGRAMS
3-1.
Overall Block Diagram (1/3) ··········································· 3-1
3-2.
Overall Block Diagram (2/3) ··········································· 3-3
3-3.
Overall Block Diagram (3/3) ··········································· 3-5
3-4.
Power Block Diagram (1/2) ············································· 3-7
3-5.
Power Block Diagram (2/2) ············································· 3-9
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
Frame Schematic Diagrams ············································· 4-1
Frame Schematic Diagram (1/2) ····································· 4-1
Frame Schematic Diagram (2/2) ····································· 4-3
4-2.
Schematic Diagrams ························································ 4-5
CD-515 FLEXIBLE (CCD IMAGER) ··························· 4-7
ST-111 (FLASH DRIVE) ············································· 4-35
FL-147 (FLASH UNIT) ··············································· 4-36
PL-001 FLEXIBLE (PLUNGER) ································ 4-36
CF-099 (CF/MS CONNECTOR) ································· 4-37
BB-005 FLEXIBLE
(SY-DD EXTENSITON BOARD) ······························· 4-39
MS-211 FLEXIBLE
(SY-CF EXTENSION BOARD) ·································· 4-41
JK-269 FLEXIBLE (USB, A/V JACK) ························ 4-43
AF-008 FLEXIBLE (AF LASER) ································ 4-45
RE-003 FLEXIBLE (SHUTTER SWITCH) ················ 4-45
BT-026 FLEXIBLE (BATTERY IN) ···························· 4-46
LI-072  FLEXIBLE
(LITHIUM  BATTERY) ··············································· 4-46
CONTROL SWITCH BLOCK
(SW51610) (REAR SW) ·············································· 4-47
CONTROL SWITCH BLOCK
 (SW51610) (MODE SW) ············································ 4-49
4-3.
Printed Wiring Boards ··················································· 4-51
CD-515 FLEXIBLE ······················································ 4-53
ST-111 ··········································································· 4-61
FL-147 ·········································································· 4-61
PL-001 FLEXIBLE ······················································ 4-62
CF-099 ·········································································· 4-63
BB-005 FLEXIBLE ······················································ 4-63
MS-211 FLEXIBLE ····················································· 4-64
JK-269 FLEXIBLE ······················································· 4-65
AF-008 FLEXIBLE ······················································ 4-66
BT-026 FLEXIBLE ······················································ 4-66
RE-003 FLEXIBLE ······················································ 4-66
LI-072 FLEXIBLE ······················································· 4-66
4-5.
Mounted Parts Location ················································ 4-71
Section
Title
Page
5.
REPAIR  PARTS  LIST
5-1.
Exploded Views ······························································· 5-2
5-1-1. Main Block ······································································ 5-2
5-1-2. Cabinet (Front) Block ······················································ 5-3
5-1-3. Grip Block ······································································· 5-4
5-1-4. Lens Block ······································································· 5-5
5-1-5. Cabinet (Upper) Block ···················································· 5-6
5-1-6. Cabinet (Rear) Block ······················································· 5-7
5-2.
Electrical Parts List ························································· 5-8
Section
Title
Page
Page of 57
Display

Sony DSC-V3 (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony DSC-V3 (serv.man2) Service Manual ↓ Size: 10.27 MB | Pages: 57 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DSC-V3 (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony DSC-V3 (serv.man2) Digital Camera. Information contained in Sony DSC-V3 (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.