Sony DSC-V1 (serv.man2) Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DSC-V1
COVER
COVER
1-2. DISCHARGING OF THE ST-083
FLEXIBLE BOARD’S CHARGING
CAPACITOR (C333)
CAPACITOR (C333)
The charging capacitor (C333) of the ST-083 flexible board is
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the LND390 (positive) and the LND391
(negative) terminals on the ST-083 flexible board with the short jig
about 10 seconds.
(negative) terminals on the ST-083 flexible board with the short jig
about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
ST-083 board
LND390
LND391
Capacitor
Ver 1.2 2004.10
1-2
DSC-V1
1-3. NOTE IN LENS FRAME
INSTALLATION
When tightening a screw, have both sides of the lens block assembly
so as not for the load to depend.
so as not for the load to depend.
P2
×
4
Lens holder
Lens block assembly
1-4. NOTES ON HANDLING THE LASER DIODE
[LASER UNIT (D333)]
The laser diode may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
potential difference generated by the charged electrostatic load, etc.
on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
Note:
Adjustment is needed when laser unit (D333) is replaced.
Refer to “16. Hologram AF Data Input” and “17. Hologram
AF Angle Check” of SERVICE MANUAL, ADJ
(987626151.pdf).
Refer to “16. Hologram AF Data Input” and “17. Hologram
AF Angle Check” of SERVICE MANUAL, ADJ
(987626151.pdf).
Laser unit
(D333)
(D333)
1-3E
DSC-V1
1-5. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
Abnormality when flash is being
charged.
charged.
2-1
SECTION 2
DISASSEMBLY
DSC-V1
COVER
COVER
HELP
HELP
The following flow chart shows the disassembly procedure.
SERVICE POSITION
Discharging the Capacitor
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
HELP
HELP
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
HELP
DISASSEMBLY
HELP
DISASSEMBLY
HELP
DISASSEMBLY
DISASSEMBLY
DISASSEMBLY
Click on the first or last page to see other DSC-V1 (serv.man2) service manuals if exist.