DOWNLOAD Sony DSC-U60 (serv.man2) Service Manual ↓ Size: 6.2 MB | Pages: 56 in PDF or view online for FREE

1-1

1 k

Ω

/1 W

Wrap insulating tape.

Short-circuit between the A (positive) and the B (negative) terminals
on the ST-80 board with the short jig about 10 seconds.

Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.

When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.

The charging capacitor (C601) of the SL-61 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off.  Therefore, the remaining
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

R:1 k

Ω

/1 W

 

(Part code: 1-215-869-11)

ST-80 board

ST-80 board

B

A

1-2

• C: ss: ss

You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)

• E: ss: ss

Contact your Sony dealer or local
authorized Sony service facility.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory stick”.

Insert a new “Memory Stick”.

Cause

Trouble with hardware.

Unformatted memory stick is inserted.

Memory stick is broken.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

  E:61:ss

  E:91:ss

Checking of lens drive circuit.

When failed in the focus initialization.

Checking of flash unit or replacement
of flash unit.

—

Abnormality when flash is being
charged.

1-3E

Waterproof check needs to be performed with the following
procedures, because after the service, the unit can not be put into
water with its internal unit installed to check waterproofing property.

1. Remove the LCD and the electrical unit from the main cabinet

assy.

1. Fix the LCD cabinet assy to the main cabinet assy with four

screws.

Note : Before installation, check that no dirt, no hair, no sand,

no dust, no salt or no lint, is attached on the O-ring
and the O-ring mating surface of the LCD cabinet assy.

: Dirt or damages on the O-ring and the O-ring mating

surface become a cause of water leakage.

Main cabinet assy

2

 LCD

1

 LCD cabinet assy

3

 Electrical unit

2. Close the waterproof cover and lock the lock switch.

Note : Before installation, check that no dirt, no hair, no sand,

no dust, no salt or no lint, is attached on the O-ring
and the O-ring mating surface of the waterproof cover.

: Dirt or damages on the O-ring and the O-ring mating

surface become a cause of water leakage.

The method of checking waterproofing property is to put the
prepared unit into water and leave it.

1. Put the unit into water in a tank, a bath tub or a swimming pool,

and leave it at least 15 to 20 minutes. Depth of water in the tank
should be 1.5 m.

2. After 15 to 20 minutes, pick up the unit from water and wipe

the unit with clean, dry, soft cloth. Then open the LCD cabinet
assy and the waterproof cover and check that no water leakage
can be seen.

Install removed electrical unit and LCD to the main cabinet assy.
Tighten the LCD cabinet assy with designated torque.
(Refer to 1-4-2. Assembling the Cabinet Assy.)

Tighten the screws by following order 
shown in the left figure bit at a time, 
then tighten them with designated 
torque at last.

Important
Screw Torque: 0.20 

±

0.02 N.m

1

3

2

4

O-ring mating surface

O-ring

Lock switch

Depth of water

: 1.5 m

Water

A tank, a bath tub, a swimming pool and so on.

O-ring mating surface

O-ring

2-1

The following flow chart shows the disassembly procedure.

Discharging the Capacitor