DOWNLOAD Sony DSC-U40 (serv.man2) Service Manual ↓ Size: 2.58 MB | Pages: 50 in PDF or view online for FREE

1-1

1 k

Ω

/1 W

Wrap insulating tape.

Short-circuit between the A (positive) and the B (negative) terminals
on the ST-089 board with the short jig about 10 seconds.

Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.

When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.

The charging capacitor (C601) of the SL-063 board is charged up
to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off.  Therefore, the remaining
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

R:1 k

Ω

/1 W

 

(Part code: 1-215-869-11)

B

A

ST-089 board

ST-089 board

1-2E

• C: ss: ss

You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)

• E: ss: ss

Contact your Sony dealer or local
authorized Sony service facility.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory Stick Duo”.

Insert a new “Memory Stick Duo”.

Cause

Trouble with hardware.

Unformatted memory stick duo is inserted.

Memory stick duo is broken.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

  E:61:ss

  E:91:ss

Checking of lens drive circuit.

When failed in the focus initialization.

Checking of flash unit or replacement
of flash unit.

—

Abnormality when flash is being
charged.

2-1

2-2

The following flow chart shows the disassembly procedure.

1

Open the lid.

2

Lock ace 

x2

3

Close the lid.

4

Lock ace 

x4

5

Claw

6

Front cabi

7

SW-411: CN001

8

Rear cabi

6

13

2

7

4

4

4

5

8

2

6

4

3

1

5

2

3

4

1

2

5

3

6

8

1

1

2

1

4

6

7

8

5

6

5

9

7

1

2

1

3

4

6

5

1

2

4

3

1

7

8

5

4

5

2

4

7

1

Tapping P2 M1.7x5 

x2

2

CCD block

3

Seal rubber

4

Optical filter

1

Tapping P2 

x1

2

Cabi (upper)

3

DD-205: CN916

4

DD-205: CN909

5

Tapping P2 

x1

6

Cabi (lower)

1

Tapping P2 

x2

2

Lens unit

1

CH-133: CN102

2

Tapping P2 

x1

3

CH-133

4

Label

5

Tapping P2 

x1

6

Claw 

x3

7

Tape

8

Flexible board

9

SL-063

1

TY-017: CN918

2

TY-017: CN919

3

TY-017: CN921

4

TY-017: CN923

5

Tapping P2 

x2

6

TY-017

7

Tapping P2 

x1

8

Frame

9

MS-167

1

TY-017: CN922

2

Tapping P2 

x1

3

Boss 

x2

4

Lifting up the PD-200.

5

Claw 

x2

6

PD-200: CN807

7

PD-200

8

PD-200: CN803

9

LCD block

1

Sheet

2

Tapping P2 

x1

3

DD-205

4

DD-205: CN001

5

Tapping P2 

x1

6

US-008

1

Claw 

x3

2

LCD holder

3

Solder 

x3

4

Sheet

5

Claw 

x4

6

Back light

7

LCD

1

TY-017: CN901

2

Tapping P2 

x1

3

TY-017: CN902

4

Claw

5

Lens block

6

6

9

3

2

2

3

4

1

9

3

2-3

2-4

DD-205

US-008

memor

y stic

k

connector

MS-167

PD-200

TY

-017

Battery holder assembly

Cabinet (upper) 
block assembly

Lens block section

OP-018 board

Front panel section

Insert the batteries

*

.

*

: size AAA

Nickel Metal Hydride
batteries (x2).