DOWNLOAD Sony DSC-U30 (serv.man2) Service Manual ↓ Size: 2.75 MB | Pages: 57 in PDF or view online for FREE

1-1

1 k

Ω

/1 W

Wrap insulating tape.

Short-circuit between the A (positive) and the B (negative) terminals
on the ST-79 board with the short jig about 10 seconds.

Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.

When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.

The charging capacitor (C601) of the SL-59 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand.  The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off.  Therefore, the remaining
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.

ST-79

R:1 k

Ω

/1 W

 

(Part code: 
1-215-869-11)

A

B

1-2E

• C: ss: ss

You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)

• E: ss: ss

Contact your Sony dealer or local
authorized Sony service facility.

Display Code

  C:32:ss

  C:13:ss

Countermeasure

Turn the power off and on again.

Format the “Memory stick”.

Insert a new “Memory Stick”.

Cause

Trouble with hardware.

Unformatted memory stick is inserted.

Memory stick is broken.

Caution Display During Error

SYSTEM ERROR

FORMAT ERROR

MEMORY STICK ERROR

  E:61:ss

  E:91:ss

Checking of lens drive circuit.

When failed in the focus initialization.

Checking of flash unit or replacement
of flash unit.

—

Abnormality when flash is being
charged.

2-1

The following flow chart shows the disassembly procedure.

Discharging the Capacitor

2-2

The procedure for a service position

1

2-1.

CABINET (FRONT) ASSEMBLY ............................ (PAGE 2-3)

2

2-3.

CABINET (REAR) ASSEMBLY ............................... (PAGE 2-4)

3

2-4.

PD-174 BOARD ...................................................... (PAGE 2-4)

4

2-5.

BOTTOM FRAME ASSEMBLY ............................... (PAGE 2-5)

5

2-6.

LENS BLOCK ASSEMBLY ..................................... (PAGE 2-5)

6

2-9.

TY-20 BOARD ........................................................ (PAGE 2-7)

7

2-10. CABINET (UPPER) ASSEMBLY ............................ (PAGE 2-7)

8

2-11. US-7 BOARD .......................................................... (PAGE 2-8)

9

2-12. DD-209 BOARD ..................................................... (PAGE 2-8)

Memory stick connector

Lens block assembly

Cabinet (upper) block assembly

Cabinet (front) block assembly

TY-20 board

DD-209 board

US-7 flexible board

PD-174 board

USB cable
(1-823-932-11)

BT holder assembly

LCD module

Insert the batteries

*

.

*

: size AAA

Nickel Metal Hydride batteries (x2).

PC