Sony DSC-T9 (serv.man15) Service Manual ▷ View online
6-3
DSC-T9_ADJ
Method for formatting the Music
If you cannot play back a Music file for the Slide Show, the Music file might be corrupted. If
this happens, perform [Format Music].
When [Format Music] is performed, all the Music files are erased. Use the supplied software
“Music Transfer” to activate [Download Music].
this happens, perform [Format Music].
When [Format Music] is performed, all the Music files are erased. Use the supplied software
“Music Transfer” to activate [Download Music].
The message “All data will be erased Ready?” appears.
Format Music
OK
Formats the Music files. All data other than Music files
remain as it is.
remain as it is.
Cancel
Cancels the formatting.
6-4
DSC-T9_ADJ
Precaution on Replacing the SY-141 board
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setteing
because of broadcast system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code
is right. If not, rewrite to the right value.
because of broadcast system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code
is right. If not, rewrite to the right value.
VIDEO OUT Default Data
Page
Address
Data
NTSC
PAL
4F
8D
00
01
4F
A2
00
01
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
[Save]
on the SEUS screen.
6) Select page: 80, address: 34, and check that the data is “00”.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-141 board was replaced, initial language setting may be changed. Accordingly, change the following data so
as to set same initial language as that of the set distributing in each region.
as to set same initial language as that of the set distributing in each region.
Initial language: Language displayed at the next starting if the setting of Setup menu was reset.
It is different from the language setting selectable with the menu.
Initial Language Data
Page
Address
Data
Language
GP1
GP2
GP3
GP4
4F
8C
00
English
z
z
z
01
Japanese
z
04
Spanish
z
z
06
Portugal
z
08
Simplified Chinese
z
0B
Russian
z
0D
Korean
z
Note:
GP1 is fixed to Japanese.
GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean.
GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Portugal, Simplified Chinese, or Korean.
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
[Save]
on the SEUS screen.
5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
6-5
DSC-T9_ADJ
Replaced parts
Block
Mounted parts
Board
replacement
replacement
replacement
Adjusting item
Adjustment
LCD unit
Back light unit
(AF illumination LED)
(Timing gen., CCD signal process)
(Camera DSP)
(Video amp.)
(64M super AND) (Note 4)
(YAW, PITCH sensor)
LCD901
D901
D002
IC101
IC301
IC605
IC401
SE501, SE502
(COMPLETE)
(COMPLETE) (Note 3, 4, 5)
Lens block
CCD block assy (Including CD-597 flexible board and CCD imager)
Flash unit
LCD block
LCD block
ST-131 board
SY-141 board
SY-141 board
SY-141 board
SY-141 board
SY-141 board
ST-131 board
SY-141 board
VIDEO adjustment
Video output level adj.
z
z
z
CAMERA adjustment 1
Hall adj.
z
z
(Note 1)
Wide limit adj.
z
z
CAMERA adjustment 2
Flange back adj.
z
z
z
CAMERA adjustment 3
Flange back check
z
z
z
F No. compensation
Measure gain adj.
Mechanical shutter adj.
Light value adj.
(Note 2)
AWB 3200K-5800K standard data input
z
z
z
Color reproduction adj. & check
CCD linearity check
CCD white defect compensation check
CCD black defect compensation check
CAMERA adjustment 6
Strobe adj.
z
z
z
z
z
CAMERA adjustment 7
Auto focus illumination check
z
z
z
(Note 1)
Angular velocity sensor sensitivity adj.
z
z
z
V-COM adj.
White Balance adj.
(Note 1)
Initialization of data
z
z
LCD adjustment
CAMERA adjustment 4
z
z
CAMERA adjustment 5
z
z
z
z
z
z
1-1. Adjusting items when replacing main parts and boards
When replacing main parts and boards, adjust the items indicated by z in the following table.
Note 1:
The automatic Adjustment Program does not support the “Initialization of data” , “Wide Limit Adjustment” and “Angular
Velocity Sensor Sensitivity Adjustment”. Perform them manually.
Velocity Sensor Sensitivity Adjustment”. Perform them manually.
Note 2:
Use the AWB Adjustment Program (T9AwbAdjustment.exe).
Note 3:
When replacing the SY-141 board, erase the data in internal memory of the board before replacement.
Note 4:
When replacing the SY-141 board or the IC401 on the SY-141 board, execute formatting and initialize the internal memory after
replacement.
replacement.
Note 5:
When replacing the SY-141 board, perform “VIDEO OUT Default Data Check” and “Initial Language Data Check” after
replacement.
replacement.
Table 6-1-1
6-6
DSC-T9_ADJ
1-2. List of service tools
•
Oscilloscope
•
Color monitor
Fig. 6-1-1
Note1:
Personal computer
OS:
OS:
Windows98/98SE/Me/2000/XP Home/XP Pro
RAM:
256MB or more recommended
USB:
2.0 recommended (also compatible with 1.1)
Two connectors are required.
Two connectors are required.
Note2:
In using the 9 colors chart on the pattern box PTB-450, adjust the chart size through the procedure shown below so that it
matches to the pattern box PTB-450.
1) Prepare a woody board A of the thickness 5 mm, and paint it mat-black.
2) Fit the 9 colors chart in the woody board A, and secure the chart with a black tape, etc. to shield the light.
matches to the pattern box PTB-450.
1) Prepare a woody board A of the thickness 5 mm, and paint it mat-black.
2) Fit the 9 colors chart in the woody board A, and secure the chart with a black tape, etc. to shield the light.
Fig. 6-1-2
360 mm
155 mm
280 mm
woody boad A
woody boad A
9 colors chart
135 mm
Personal computer
(Note 1)
(Note 1)
J-1
J-10
J-9
J-7
HASP key and application
for adjustment (SEUS)
for adjustment (SEUS)
Contact our service headquater of each area
how to get the application for adjustment
(SEUS) and HASP key.
how to get the application for adjustment
(SEUS) and HASP key.
J-2
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-4
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-6
Minipattern box
J-6082-353-B
J-6082-353-B
Siemens star chart
J-6080-875-A
J-6080-875-A
Back ground paper
J-2501-130-A
J-2501-130-A
9 colors chart (Note 2)
For PTB-1450:
J-6082-562-A
J-6082-562-A
J-5
USB, A/V, DC IN cable
for multi-use terminal
1-830-848-11
for multi-use terminal
1-830-848-11
J-3
J-8
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
AC power adaptor
AC-LS5
1-479-284-12
AC-LS5
1-479-284-12
J-11
Click on the first or last page to see other DSC-T9 (serv.man15) service manuals if exist.