DOWNLOAD Sony DSC-T700 (serv.man3) Service Manual ↓ Size: 810.6 KB | Pages: 38 in PDF or view online for FREE

6-24

DSC-T700_ADJ

“CAMERA Adjustment 7” is available only once after the
power is turned on. If the adjustment is retried, turn off the
power and turn on again.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Strobe Adj.
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of CAMERA Adjustment 7.
2) The Automatic Adjustment Program executes the “1. Data

Setting during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “5. Preparing the Flash
Adjustment Box” (see page 6-7).)

4) Press the [OK]  button, and the “2. Strobe Adj.” will be ex-

ecuted.

5) During execution of “2. Strobe Adj.”, the following message

is displayed. After checking the flashing of strobe light, click
the  [OK]  button. (This message is displayed 2 times during
execution of adjustment.)

6) Upon successful completion of “2. Strobe Adj.”, “3.Release

of Data Setting during Camera Adj.” is executed.

7) Upon successful completion of all items of the CAMERA

Adjustment 7, the following message is displayed. Click the
[OK] button.

[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Auto Focus Illumination Check
3. Release of Data Setting during Camera Adj.

[Adjusting method]
1) Click the [Start] button of CAMERA Adjustment 8.
2) The Automatic Adjustment Program executes the “1. Data

Setting during Camera Adj.”.

3) Upon successful completion of the “1. Data Setting during

Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “5. Preparing the Flash
Adjustment Box” (see page 6-7).)

4) Press the [OK]  button, and the “2. Auto Focus Illumination

Check” will be executed.

5) Upon successful completion of the “2. Auto Focus Illumina-

tion Check”, the “3. Release of Data Setting during Camera
Adj.” will be executed successively.

6) Upon successful completion of all items of the CAMERA

Adjustment 8, the following message is displayed. Click the
[OK] button.

6-25

DSC-T700_ADJ

Preparation:
1) Read the PITCH sensor (SY-208 board SE511) sensitivity writ-

ten on repair parts, and named this as S

502

.

2) Read the YAW sensor (SY-208 board SE511) sensitivity writ-

ten on repair parts, and named this as S

501

.

With the direction mark of the angular velocity sensor located in
the lower left position, read the data value.

Perform this adjustment only when replacing the angular velocity
sensor or lens block. When the microprocessor, circuit etc. is dam-
aged, don’t perform this adjustment but check the operations only.

Before adjustment, read the following data and record them.
When the SY-208 board is replaced, read out the data before the
replacement, and record them.

Reading out method:
1) Read out the data in Block: 11, Page: 61, Address: 0E10, and

name this as Dp.

2) Read out the data in Block: 11, Page: 61, Address: 0E11, and

name this as Dy.

3) Read out the data in Block: 11, Page: 61, Address: 0E07, and

name this as Fpy (Note2).

The previous data (Dp, Dy and Fpy) can be read from
the SY-208 board and it can be saved in the PC as a
file by using the Automatic Adjustment Program.
(Refer to “10-4. Angular Velocity Sensor Sensitivity
Adjustment”)

If correct data reading failed, replace the lens together
with the SY-208 board.

Note down the sensitivity displayed on the angular velocity sensor of
the repair parts. At this time, note down also to which board it was
attached to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.

There are only one type of a repair parts.

The sensor incorporates a precision oscillator. Handle it with care as
if it dropped, the balance of oscillator will be disrupted and opera-
tions will not be performed properly.

Adjustment Block

11

Adjustment Page

61

Adjustment Address

0E10, 0E11, 0E07

The sensor sensitivity of SE511 of the SY-208 board is writ-
ten only repair parts.

198

198

Direction Mark

Hand Writing

For the sensor sensitivity value 198

PPP

YYY

YYY : YAW Sensor sensitivity

S

501

SE511

PPP : PITCH Sensor sensitivity

S

502

6-26

DSC-T700_ADJ

[Adjusting method]
1) Click the [Start] button of Camera Adjustment 9, and the fol-

lowing screen will appear.

The buttons on this screen provide the following functions.
[Read] button: Reads and displays the previous data (Dp, Dy

and Fpy

*1

) from the SY-208 board.

*1: The Fpy box is displayed, when you give a check to the

checkbox at lower left of “Input the PITCH/YAW and FN
data”.

[Save] button: Saves the previous data (Dp, Dy and Fpy) in

the PC as a file.

[Load] button: Loads and displays the previous data (Dp, Dy

and Fpy) from the file saved in the PC.

Note down the PITCH/YAW and FN data on the replacement lens for
repair.

Adjustment Block

11

Adjustment Page

61

Adjustment Address

0E10, 0E11, 0E07

The PITCH/YAW and FN data of lens is written only re-
pair parts.

Preparation:
1) Read the PITCH data written on repair parts, and named this

as L

1

.

2) Read the YAW data written on repair parts, and named this as

L

2

.

3) Read the FN data written on repair parts, and named this as

Fpy.

YAW data 

t

 L

2

PITCH/YAW Data

PITCH data 

t

 L

1

P.PP / Y.YY

FN Data

FN data 

t

 Fpy

XX

FN

L1/L2

• Default file name is as follows:

2) Input the previous data (Dp, Dy and Fpy

*1

) into screen.

If the previous data cannot be read, give a check to the checkbox
at lower left of screen.
*1: The Fpy box is displayed, when you give a check to the

checkbox at lower left of “Input the PITCH/YAW and FN
data”.

3) Input the sensitivity of respective sensors (S

501

, S

502

) read at

“Preparation” into the screen.

4) Input the PITCH/YAW and FN data of lens (L

1

, L

2

 and Fpy)

read at “Preparation” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.

In order to get the correct value for the adjustment, it is
necessary to input a decimal point (“period” or
“comma”) as same format as windows setting because
“Numeric Value Format” depend on the language.
(F:123 456 789,00, GB:123,456,789.00,
D:123.456.789,00)
“Numeric Value Format” setting is available in “Con-
trol Panel”-“Regional and Language Options”.

5) Click the [OK] button, and the adjustment data is then calcu-

lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.

6) Upon successful completion of the data writing, the following

screen will appear. Check that the steady shot function oper-
ates normally.

DSC-T700_D

p

D

y

DT_xxxxxxxx_yyyymmdd.dat

Date
USB serial number
Data name

6-27

DSC-T700_ADJ

The adjustment items of LCD system adjustment are as listed in
Table 6-1-5. The Automatic Adjustment Program executes the ad-
justment items if the LCD Adjustment Start button is clicked.

LCD

White Balance

Adjustment Adj.

11

60

0409, 040A

Touch
Panel

Touch Panel Adj.

(Note)

Adjustment

The adjustment data cannot be read or written the SeusEX.

Click the [LCD SYSTEM ADJUSTMENT] button on the Main Menu
screen, and the “LCD SYSTEM ADJUSTMENT” screen in Fig.
6-1-24 will appear.

1

[To Menu] button
Return to the main menu.

2

[Start] button
Each adjustment “LCD Adjustment” or “Touch Panel Adjust-
ment” starts.

3

[Reboot] button
When this button is clicked, the camera is rebooted.

3

2

1