Sony DSC-T500 Service Manual ▷ View online
SERVICE MANUAL
LEVEL
3
Sony EMCS Co.
Revision History
Revision History
DIGITAL STILL CAMERA
2009L0500-1
© 2009.12
Published by Tokai TEC
9-852-616-14
Ver. 1.3 2009.12
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Thai Model
Argentine Model
Brazilian Model
Tourist Model
DSC-T500
Link
SERVICE NOTE
PRINTED WIRING BOARDS
SCHEMATIC DIAGRAMS
REPAIR PARTS LIST
Link
DSC-T500_L3
Internal memory
ON BOARD
Internal memory
ON BOARD
Photo: Silver
• Precaution on Replacing the SY-209 Board
Revised-3
Replace the previously issued
SERVICE MANUAL 9-852-616-13
with this Manual.
SERVICE MANUAL 9-852-616-13
with this Manual.
— 2 —
DSC-T500_L3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
FLEXIBLE Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Replace only with the same or equivalent type.
1-1
DSC-T500_L3
1. SERVICE NOTE
SY-209 BOARD (SIDE B)
SE1001
YY: YAW Sensor sensitivity
PP: PITCH Sensor sensitivity
YY
PP
SE1002
Note:
The sensor sensitivity of SE1001 and SE1002 of SY-209 board is written only repair parts.
1-1. PRECAUTION ON REPLACING THE SY-209 BOARD
SETTING OF LANGUAGE OF SY-209 BOARD
Two types of SY-209 BOARD, COMPLETE (SERVICE) are exists.
Refer to table below for language settings of two kinds of SY-209 board.
Refer to table below for language settings of two kinds of SY-209 board.
A-1547-808-
B
SY-209 BOARD, COMPLETE (SERVICE 124) (EXCEPT AEP, UK)
A-1547-809-
B
SY-209 BOARD, COMPLETE (SERVICE 35) (AEP, UK)
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
Angular Velocity Sensor
When you replace to the reparing board, write down the sensitivity displayed on the angular velocity sensor (SE1001 and
SE1002).
Refer to Service Manual ADJ, and perform “Angular velocity sensor sensitivity adj”.
SE1002).
Refer to Service Manual ADJ, and perform “Angular velocity sensor sensitivity adj”.
JE
z a
a
a
a
a
a a a a a
PAL
US
z a
a a
a
a
NTSC
CND
z a
a a
a
a
NTSC
z a
a
a
a
a
a a a a a
PAL
z a
a
a
a
a
a a a a a
PAL
a a
z
a
a
a
a a a a a
NTSC
AUS
z a
a a
a
a
PAL
HK
z a
a
a
a
a
a a a a a
PAL
CH
a a
a
a
z
a
a a a a a
PAL
KR
a a
a
a
a
a
z a a a a
NTSC
Thai
a a
a
a
a
a
a a a z a
PAL
AR
a a
z
a
a
a
a a a a a
NTSC
BR
a a
a
z a
a
a a a a a
NTSC
a a a a a a
a z
a a a a a a a a a PAL
z a a a a a
a
a a a a a a a a a PAL
z a a a a a
a a
a a a a a a a a a PAL
UK
z a a a a a
a
a a a a a a a a a PAL
z: INITIAL LANGUAGE
VID
E
O
OU
T
Default
AEP
ARE
A
SELECTABLE LANGUAGE
E
Japanese
English
French
German
Spanish
Italian
Portuguese
Simplified
Chinese
Traditional
Chinese
Dutch
Russian
Korean
Persian
Arabic
Thai
Malay
Swedish
Norwegian
Danish
Finnish
Polish
Czech
Hungarian
Turkish
Greek
SY-209
Board
SERVICE
124
SERVICE
35
Language that can be selected about SY-209 board
Ver. 1.3 2009.12
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
1-2
DSC-T500_L3
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1:
When replacing the SY-209 board, erase the data in internal memory of the board before replacement.
Note 2:
When replacing the SY-209 board, execute formatting and initializing the internal memory after replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
Formats the internal memory.
• Note that formatting permanently erases all data in the internal memory, including even protected images.
1
Touch [Format].
The message “All data on internal memory will be erased” appears.
The message “All data on internal memory will be erased” appears.
2
Touch [OK].
Formatting starts.
Formatting starts.
To cancel the formatting
Touch [Cancel] or [BACK] in step
2
.
Format
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having sufficient free capacity.
2 Touch [Copy].
The message “All data on internal memory will be copied” appears.
3 Touch [OK].
Copying starts.
To cancel the copying
Touch [Cancel] or [BACK] in step
3
.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot select images to copy.
• The original images in the internal memory are retained even after copying. To delete the contents of the
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then format the internal memory
([Format] in [Internal Memory Tool])
([Format] in [Internal Memory Tool])
• A new folder is created on the “Memory Stick Duo” and all the data will be copied to it. You cannot
choose a specific floder and copy images to it.
choose a specific floder and copy images to it.
• The
DPOF
(Print order) marks on the images are not copied.
Copy
1-2. PRECAUTION ON REPLACING THE LENS
When replacing the lens, write down the PITCH/YAW data and wide limit data given on the data sheet of the replacement lens for service.
Refer to Service Manual ADJ, and perform “Wide Limit adj” and “Angular velocity sensor sensitivity adj”.
Refer to Service Manual ADJ, and perform “Wide Limit adj” and “Angular velocity sensor sensitivity adj”.
Note:
The PITCH/YAW data and wide limit data of lens are written only repair parts.
1-3. PRECAUTION ON REPLACING THE MICROPHONE
Exchange two pieces at the same time when exchange microphones.
Adjust the condition of the reflow to 240 degrees or less and make time that it reaches 240 degrees within 30 seconds.
Do not close the sound hole when reflow.
.
Adjust the condition of the reflow to 240 degrees or less and make time that it reaches 240 degrees within 30 seconds.
Do not close the sound hole when reflow.
.
Wide Limit Data (2-byte data)
XXXX
YAW data
t
L2
PITCH/YAW Data
PITCH data
t
L1
P.PP / Y.YY
P.PP/ Y.YY
XXXX
