DOWNLOAD Sony DSC-T500 (serv.man3) Service Manual ↓ Size: 1.49 MB | Pages: 36 in PDF or view online for FREE

6-4

DSC-T500_ADJ

2) As shown below, connect the lead wires attached with alligator clips to the check land and GND of the board so as to enable a short circuit

or open circuit to the GND.

1) Connect the set to the modified multi-output stand.
2) Connect the PC and the modified multi-output stand.
3) Turn on the power with the lead wires connected to the GND of the board (Adjustment mode ON state) as mentioned in “1-3-1. Multi-

Output Stand Modification Procedure”.

4) Change the USB driver to the one for SeusZ.

The set has been so designed that the power is turned off automatically in about 60 seconds after the power was turned on.
If the power is turned off automatically while the USB driver is changing, turn on the power again and retry.

1

45

48

50

47

49

19

1

23

21

20

22

CN001

CN003

CL001

CL002

CL003

2

46

7

6

5

1

CN002

C001

C002

LF001

J001

J002

FB001

VDR001

FB002

VDR002

VDR003

FB003

VDR004

VDR005

FB006

R001

1

4

32

1

5

3

4

Short circuit: Adjustment mode ON state

Open circuit: Adjustment mode OFF state

HDMI OUT

A/V OUT

(STEREO)

USB

DC IN

from the Conductor side

from the Component side

6-5

DSC-T500_ADJ

1) Connect the equipment for adjustments according to Fig. 6-1-4.
2) Start up the application for adjustment (SeusZ).

Before the adjustment, refer to “1-3. Preparation before Using Adjustment Software (SeusZ)”.

The set has been so designed that the power is turned off automatically in about 60 seconds after the power was turned on.
The power is not turned off automatically if the SeusZ is started and “connect” is executed.

Video

Audio (L)

Audio (R)

Color monitor

Video system Adjustment
(Composite video level adj.)

Oscilloscope

Terminated
75 

Ω

PC 

(The SeusZ must be installed in the PC.)

OS: Windows 2000/XP/Vista
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
         Two connectors are required.

HASP Key

To USB 
connector

AC IN

AC power adaptor
AC-LS5
(1-479-284-51)

 To DC IN jack

 To USB jack

 To A/V OUT jack

Multi-output stand
(A-1548-091-A)
(Note 1)

Camera table
(J-6082-384-A)

Camera System
Adjustment

Short: Adjustment mode ON state
Open: Adjustment mode OFF state

Multiple connector 
extension
(J-6082-701-A)

AV cable
(1-824-097-11)

USB cable
(1-829-868-41)

6-6

DSC-T500_ADJ

Unless otherwise specified, set the switches as follows and perform adjustments.
1. Mode switch .................................................................. Still image
2. HOME items (Shooting) ............................................... Auto Adjustment
3. Zoom lever .................................................................... WIDE end
4. Digital Zoom

(Settings – Shooting Settings – Shooting Settings 1) .... Off

1) 9 colors chart (Standard picture frame).

When performing adjustments using the 9 colors chart, adjust
the picture frame as shown in Fig. 6-1-5. (Standard picture
frame)

2) Clear chart (Standard picture frame)

Remove the 9 colors chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations dur-
ing this time)

Set the distance from the front of the lens to the pattern box as
shown in Fig. 6-1-6.

Adjust the camera position and direction
to obtain the LCD screen or the monitor
TV display shown in Fig. a.

Transparent window

A

B

A

C

B

C

C14: Filter for AWB 5800K adjustment

A

2

Effective picture frame

C14

Blue

Magenta

Red

White

Cyan

Green

Yellow

W14

Fig. a

LCD screen or under scan

monitor TV picture

A = B

C =

3

B

(                                    )

Pattern box

Front of the lens

L = About 9 cm

L

Camera

6-7

DSC-T500_ADJ

1) It takes about 30 minutes for pattern box to stabilize its brightness.

Turn on the pattern box 30 minutes before the adjustment starts.

2) Make arrangement so that the outside light does not enter the chart surface in the pattern box.

Also, place a board between chart and camera, and make a hole at the lens part of the board so that the camera is not reflected in the
shot image screen.
(Adjustment may not be performed correctly due to the influence of outside light.)

Place a box to block a section between pattern box and camera.

Place a board having a hole in front of the camera and cover the pattern box and camera with a blackout curtain

3) Control of color chart

The color chart will fade if it is exposed to direct sunlight or strong light.
Since the fading of color chart progresses even with the light in the pattern box, remove and store the color chart when it is not used.
Remove the color chart and store it.
Store the color chart in a place not exposed to direct light, avoiding high temperature and humidity.
Use the color chart for about three years, and afterward replace it with a new chart.

Pattern box

Front of the lens

Make the hole of the same
size as the lens. 

Make the hole of the same
size as the pattern box. 

L = About 9 cm

L

Camera

Pattern box

Front of the lens

Board that opens hole
to lens part

L = About 9 cm

L

Camera

Cover with a blackout curtain