DOWNLOAD Sony DSC-T500 (serv.man3) Service Manual ↓ Size: 1.49 MB | Pages: 36 in PDF or view online for FREE

6-2

DSC-T500_ADJ

360 mm

155 mm

280 mm

woody board A

woody board A

9 colors chart

135 mm

Personal computer
OS:

Windows2000/XP/Vista

RAM: 256 MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)

Two connectors are required.

In using the 9 colors chart on the pattern box PTB-450, adjust the chart size through the procedure shown below so that it matches
to the pattern box PTB-450.
1) Prepare a woody board A of the thickness 5 mm, and paint it mat-black.
2) Fit the 9 colors chart in the woody board A, and secure the chart with a black tape, etc. to shield the light.

The Multi-output stand must be modified. (Refer to “1-3-1. Multi-Output Stand Modification Procedure”)

• Oscilloscope

• Color monitor

Personal computer
(Note 1)

J-1

J-11

J-10

J-8

HASP key and application 
for adjustment (SeusZ)

Contact our service headquarters of each 
area how to get the application for 
adjustment (SeusZ) and HASP key.

J-2

Pattern box PTB-450
J-6082-200-A
 or
Small pattern box
PTB-1450
J-6082-557-A

J-5

Clear chart

For PTB-450:
J-6080-621-A

For PTB-1450:
J-6082-560-A

J-7

Minipattern box
J-6082-353-B

Siemens star chart
J-6080-875-A

Background paper
J-2501-130-A

9 colors chart (Note 2)

For PTB-1450:
J-6082-562-A

J-6

J-3

J-9

Flange back
adjustment jig
J-6082-563-A

AC power adaptor
AC-LS5
1-479-284-51

J-12

USB cable
1-829-868-41

J-4

J-14

Camera table
J-6082-384-A

J-15

J-13

Multiple connector 
extension
J-6082-701-A

Multi-output stand
UC-TE (Note 3)
A-1548-091-A

AV cable 
1-824-097-11

6-3

DSC-T500_ADJ

For the adjustment of the set, use the adjustment software (SeusZ).
Install the SeusZ before performing the adjustment.

For the USB connection of the set using the adjustment software (SeusZ), the multi-output stand must be modified to enter the
adjustment mode.

1) Remove the board from the multi-output stand through the procedure given below.

1

2

3

4

5

4

4

4

6-4

DSC-T500_ADJ

2) As shown below, connect the lead wires attached with alligator clips to the check land and GND of the board so as to enable a short circuit

or open circuit to the GND.

1) Connect the set to the modified multi-output stand.
2) Connect the PC and the modified multi-output stand.
3) Turn on the power with the lead wires connected to the GND of the board (Adjustment mode ON state) as mentioned in “1-3-1. Multi-

Output Stand Modification Procedure”.

4) Change the USB driver to the one for SeusZ.

The set has been so designed that the power is turned off automatically in about 60 seconds after the power was turned on.
If the power is turned off automatically while the USB driver is changing, turn on the power again and retry.

1

45

48

50

47

49

19

1

23

21

20

22

CN001

CN003

CL001

CL002

CL003

2

46

7

6

5

1

CN002

C001

C002

LF001

J001

J002

FB001

VDR001

FB002

VDR002

VDR003

FB003

VDR004

VDR005

FB006

R001

1

4

32

1

5

3

4

Short circuit: Adjustment mode ON state

Open circuit: Adjustment mode OFF state

HDMI OUT

A/V OUT

(STEREO)

USB

DC IN

from the Conductor side

from the Component side

6-5

DSC-T500_ADJ

1) Connect the equipment for adjustments according to Fig. 6-1-4.
2) Start up the application for adjustment (SeusZ).

Before the adjustment, refer to “1-3. Preparation before Using Adjustment Software (SeusZ)”.

The set has been so designed that the power is turned off automatically in about 60 seconds after the power was turned on.
The power is not turned off automatically if the SeusZ is started and “connect” is executed.

Video

Audio (L)

Audio (R)

Color monitor

Video system Adjustment
(Composite video level adj.)

Oscilloscope

Terminated
75 

Ω

PC 

(The SeusZ must be installed in the PC.)

OS: Windows 2000/XP/Vista
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
         Two connectors are required.

HASP Key

To USB 
connector

AC IN

AC power adaptor
AC-LS5
(1-479-284-51)

 To DC IN jack

 To USB jack

 To A/V OUT jack

Multi-output stand
(A-1548-091-A)
(Note 1)

Camera table
(J-6082-384-A)

Camera System
Adjustment

Short: Adjustment mode ON state
Open: Adjustment mode OFF state

Multiple connector 
extension
(J-6082-701-A)

AV cable
(1-824-097-11)

USB cable
(1-829-868-41)