Sony DSC-T5 (serv.man16) Service Manual ▷ View online
1-1
DSC-T5_L2
1. NOTA DE SERVIÇO
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory Stick” or internal
memory.
memory.
Cause
Trouble with hardware.
“Memory Stick” or internal memory is
unformatted.
unformatted.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
1-1. DESCRIÇÃO SOBRE AUTO-DIAGNÓSTICO VISUALIZADO
Insert a new “Memory Stick”. “Memory Stick” is broken.
Turn the power off and on again.
Trouble with internal memory.
INTERNAL MEMORY ERROR
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
—
Checking of flash unit or replacement
of flash unit. (Note)
of flash unit. (Note)
Abnormality when flash is being
charged.
charged.
Note:
After repair, be sure to perfom “1-2. PROCESS AFTER FIXING FLASH ERROR”.
1-2. PROCESSO APÓS O REPARO DO ERRO DO FLASH
When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
flash is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.
Method for Initializing the Flash Error Code
Initializes the setting to the default setting.
1
Select [OK] with v on the control button, then press z.
The message “Initialize all settings Ready?” appears.
The message “Initialize all settings Ready?” appears.
2
Select [OK] with v, then press z.
The settings are reset to the default setting.
The settings are reset to the default setting.
• Make sure that the power is not disconnected during resetting.
Initialize
OK
See the following procedure.
Cancel
Cancels the resetting.
1-2
DSC-T5_L2
1-3. MÉTODO PARA COPIAR OU APAGAR OS DADOS DA MEMÓRIA INTERNO
The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)
Note: 1
When replacing the SY-134 board, erase the data in internal memory of the board before replacement.
Note: 2
When replacing the SY-134 board or the IC401 on the SY-134 board, execute formatting and initialize the internal memory after
replacement.
replacement.
Method for Copying the Data in Internal Memory
Method for Formatting the Internal Memory
Copies all images in the internal memory to a “Memory Stick Duo”.
1
Insert a “Memory Stick Duo” having 32 MB or larger capacity.
2
Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be copied Ready?” appe ars.
The message “All data in internal memory will be copied Ready?” appe ars.
3
Select [OK] with v, then press z.
Copying starts.
Copying starts.
• Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files
using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or
possibly corrupting the data.
possibly corrupting the data.
• You cannot copy individual images.
• The original images in the internal memory are retained even after copying. To delete the contents of the
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in
(Internal Memory Tool).
• You cannot select a folder copied on a “Memory Stick Duo”.
• Even if you copy data, a
• Even if you copy data, a
(Print order) mark is not copied.
Copy
OK
See the following procedure.
Cancel
Cancels the copying.
Copying
102_COPY
A
Formats the internal memory.
• Note that formatting irrevocably erases all data in the internal memory, including even protected images.
1
Select [OK] with v on the control button, then press z.
The message “All data in internal memory will be erased Ready?” appears.
The message “All data in internal memory will be erased Ready?” appears.
2
Select [OK] with v, then press z.
The format is complete.
The format is complete.
Format
OK
See the following procedure.
Cancel
Cancels the formatting.
1-3E
DSC-T5_L2
1-4. PRECAUÇÃO NA SUBSTITUIÇÃO DA PLACA SY-134
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast
system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite
to the right value.
system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite
to the right value.
VIDEO OUT Default Data
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
[Save]
on the SEUS screen.
6) Select page: 80, address: 34, and check that the data is “00”.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-134 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial
language as that of the set distributing in each region.
language as that of the set distributing in each region.
Initial language: Language displayed at the next starting if the setting of Setup menu was reset.
It is different from the language setting selectable with the menu.
Initial Language Data
Page
Address
Data
Language
GP1
GP2
GP3
GP4
4F
8C
00
English
z
z
z
01
Japanese
z
04
Spanish
z
z
06 Português z
08
Simplified Chinese
z
0B
Russian
z
0D
Korean
z
Note:
GP1 is fixed to Japanese.
GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Português, Simplified Chinese, or Korean.
GP2 is fixed to English.
GP3 is either English, Spanish, or Russian.
GP4 is either English, Spanish, Português, Simplified Chinese, or Korean.
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 8C, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
[Save]
on the SEUS screen.
5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
Address
00
00
01
01
8D
A2
4F
4F
Page
Data
NTSC
PAL
2-1
2. DESMONTAGEM
DSC-T5_L2
NOTA PARA CONSERTO
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-126 BOARD’S CHARGING CAPACITOR (C005)
The charging capacitor (C005) of the ST-126 board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
Short-circuit between the two points with the
short jig about 10 seconds.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Click on the first or last page to see other DSC-T5 (serv.man16) service manuals if exist.