DOWNLOAD Sony DSC-T100 (serv.man4) Service Manual ↓ Size: 988.56 KB | Pages: 44 in PDF or view online for FREE

6-35

DSC-T100_ADJ

The adjustment software (SeusEX) can change operational coef-
ficients of signal processing, EVR data, etc. same as the adjust-
ment remote commander. The SeusEX performs two-way com-
munication between PC and camcorder using the USB terminal.
The two-way communication result data can be written in the non-
volatile memory.

1) Connect the HASP key to the USB terminal of the PC.
2) Connect the PC and camcorder with the USB cable.
3) Start the SeusEX on the PC.
4) Click  [Connect] on the SeusEX screen. If the connection is

normal, the SeusEX screen will be as shown in Fig. 6-2-1,
indicating the “connected” state.

The SeusEX will go in “disconnect” state, if the
camcorder is turned off (for instance, by resetting the
set). In such a case, click [Connect] on the SeusEX
screen to restore the “connected” state.

•

Block change
To change the block, click [Block] on the SeusEX screen and
enter the block to be changed. The block is displayed in hexa-
decimal notation.

•

Page change
To change the page, click [Page] on the SeusEX screen and en-
ter the page to be changed. The page is displayed in hexadeci-
mal notation.

•

Address change
To change the address, click [Address] on the SeusEX screen
and enter the address to be changed. The address is displayed in
hexadecimal notation.

•

Data change
To change the data, click [Set] on the SeusEX screen and enter
the data. The data is displayed in hexadecimal notation.
This operation does not write the data to the nonvolatile memory.

•

Data writing
To write the data to the EEPROM, click [Write] on the SeusEX
screen and enter the data value to be written.
To write the data to the flash memory, change the data value
using the [Set] on the SeusEX screen and then click [Save] to
save the data.

•

Data reading
The data displayed on the SeusEX screen are the data values at
the time when the pages and addresses were set, and they are
not updated automatically. To check the data change, click [Read]
on the SeusEX screen and update the displayed data.

6-36

DSC-T100_ADJ

Click the [Switch Check] button on the SERVICE MODE screen,
and the “SWITCH CHECK” screen will appear.

Using method:
Click the [Start] button, and the switch check will start.
During execution of switch check, the pressed switch is displayed
in orange. Also, once the switch was pressed, its name characters
change to blue in color.

Click the [SERVICE MODE] button on the Main Menu screen, and
the “SERVICE MODE” screen in Fig. 6-2-2 will appear.

1

[To Menu] button
The Main Menu screen comes back.

2

[Switch Check] button
“SWITCH CHECK” screen appears.

3

[LED Check] button
“LED CHECK” screen appears.

4

[Record Data] button
“RECORD DATA” screen appears.

5

[Aging] button
“AGING” screen appears.

1

4

5

2

3

6-37

DSC-T100_ADJ

Click the [Record Data] button on the SERVICE MODE screen,
and the “RECORD DATA” screen will appear.

The record data such as Lifetime counter is displayed.

Initializing method:
Click the [Clear shot Count] button on the screen, and the Life-
time Count data will be initialized.

Click the [LED Check] button on the SERVICE MODE screen,
and the “LED CHECK” screen will appear.

Using method:
LED ON or OFF can be controlled with [LED ON] or [LED OFF]
button on the screen.

6-38

DSC-T100_ADJ

On the AGING screen, various types of aging can be executed.
Select the type of aging to be executed with the Aging Mode
Select buttons.

Supply the power not from an AC adapter but from the fully charged
battery and execute the aging until the battery end, so that its bat-
tery use time and how many pictures the camera can record/play
back can be checked.

During the execution of aging, the camera automatically repeats
recording/playback.
During the recording, if the recording memory capacity  becomes
full, its memory is automatically formatted.
Accordingly, when executing the aging, insert the Memory Stick
into the camera and set the Memory Stick as default media.

[Preparation]
For the aging, set the camera as follows:

Switch setting:
1) Flash button ...................................................................... Auto

Home Items
1) Shooting ....................................................... Auto Adjustment
2) AF Mode

(Setting - Shooting Settings - Shooting Settings 1) ...... Single

Aging Mode Select button

In the 10MODE, perform continuous recording in accordance with
the CIPA Standard. When the 10MODE starts, the following op-
eration is repeated until the battery end.

1) The zoom moves to the TELE end.
2) The camera records a still picture with a strobe light flashed at

the maximum level.

3) The camera stands by for the time (sec.) set to the “Rec Inter-

val”.

4) The zoom moves to the WIDE end.
5) The camera records a still picture without flashing a strobe

light.

6) The camera stands by for the time (sec.) set to the “Rec Inter-

val”.

7) Each time 10 still pictures are recorded, the power is turned

off, and after the time (min.) set to the “Power Off Interval”,
the power is turned on again.

At the start of 10MODE, the counter in the camera is initialized.
This counter counts the number of recording times  during the
execution of 10MODE, and it holds the counts even during the
power off.