DOWNLOAD Sony DSC-T10 (serv.man4) Service Manual ↓ Size: 687.3 KB | Pages: 37 in PDF or view online for FREE

Model
DSC-T10 (serv.man4)
Pages
37
Size
687.3 KB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / SECTION 6 ADJUSTMENTS
File
dsc-t10-sm4.pdf
Date

Sony DSC-T10 (serv.man4) Service Manual ▷ View online

6-24
DSC-T10_ADJ
9.
CAMERA Adjustment 6
Note: “CAMERA Adjustment 6” is available only once after the
power is turned on. If the adjustment is retried, turn off the
power and turn on again.
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Strobe Adj.
3. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of CAMERA Adjustment 6.
2) The Automatic Adjustment Program executes the “1. Data
Setting during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “3. Preparing the Flash
Adjustment Box” (see page 6-9).)
Fig. 6-1-45
4) Press the [OK] button, and the “2. Strobe Adj.” will be executed.
5) During execution of “2. Strobe Adj.”, the following message
is displayed. After checking the flashing of strobe light, click
the  [OK]  button. (This message is displayed 2 times during
execution of adjustment.)
Fig. 6-1-46
6) Upon successful completion of “2. Strobe Adj.”, “3.Release
of Data Setting during CAMERA Adj.” is executed.
7) Upon successful completion of all items of the CAMERA
Adjustment 6, the following message is displayed. Click the
[OK] button.
Fig. 6-1-47
10. CAMERA Adjustment 7
[Automatic Adjustment Program execution items and
sequence]
1. Data Setting during Camera Adj.
2. Auto Focus Illumination Check
3. Release of Data Setting during Camera Adj.
[Adjusting method]
1) Click the [Start] button of CAMERA Adjustment 7.
2) The Automatic Adjustment Program executes the “1. Data
Setting during Camera Adj.”.
3) Upon successful completion of the “1. Data Setting during
Camera Adj.”, the following message is displayed. Set the sub-
ject in accordance with the message.
(For the Flash adjustment box, refer to “3. Preparing the Flash
Adjustment Box” (see page 6-9).)
Fig. 6-1-48
4) Press the [OK]  button, and the “2. Auto Focus Illumination
check” will be executed.
5) Upon successful completion of the “2. Auto Focus Illumina-
tion Check”, the “3. Release of Data Setting during Camera
Adj.” will be executed successively.
6) Upon successful completion of all items of the CAMERA
Adjustment 7, the following message is displayed. Click the
[OK] button.
Fig. 6-1-49
6-25
DSC-T10_ADJ
11. CAMERA Adjustment 8
Perform this adjustment only when replacing the angular velocity
sensor or lens block. When the microprocessor, circuit etc. is dam-
aged, don't perform this adjustment but check the operations only.
11-1. Preparation when the angular velocity sensor or
the SY-163 board is replaced
Note down the sensitivity displayed on the angular velocity sensor of
the repair parts. At this time, note down also to which board it was
attached to.
Be sure to check because if attached incorrectly, the screen will vi-
brate up and down or left and right during the steady shot operations.
Precautions on the Parts Replacement
The PITCH sensor and the YAW sensor are different parts.
Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care as
if it dropped, the balance of oscillator will be disrupted and opera-
tions will not be performed properly.
Adjustment Page
CF
Adjustment Address
0C, 0D
Note 1: The sensor sensitivity of SE501 and SE502 of the SY-
163 board is written only repair parts.
Preparation:
1) Read the PITCH sensor (SY-163 board SE501) sensitivity writ-
ten on repair parts, and named this as S
501
.
2) Read the YAW sensor (SY-163 board SE502) sensitivity writ-
ten on repair parts, and named this as S
502
.
Fig. 6-1-50
SE501
SE502
SY-163 BOARD (SIDE B)
XX
XX
YAW sensor sensitivity
t
 S
502
PITCH sensor sensitivity t S
501
11-2. Preparation when the lens is replaced
Note down the PITCH/YAW data on the replacement lens for repair.
Adjustment Page
CF
Adjustment Address
0C, 0D
Note 1: The PITCH/YAW data of lens is written only repair parts.
Preparation:
1) Read the PITCH data written on repair parts, and named this
as L
1
.
2) Read the YAW data written on repair parts, and named this as
L
2
.
Fig. 6-1-51
YAW data    t L
2
PITCH/YAW Data
PITCH data t L
1
X.XX / X.XX
6-26
DSC-T10_ADJ
11-3. Angular Velocity Sensor Sensitivity Adjustment
[Adjusting method]
1) Click the [Start] button of Camera Adjustment 8, and the fol-
lowing screen will appear.
Fig. 6-1-52
2) Input the sensitivity of respective sensors (S
501
, S
502
) read at
“Preparation” into the screen.
If only either sensor was replaced, give a check to the checkbox
for the sensor not replaced at the lower left of the screen.
3) Input the PITCH/YAW data of lens (L
1
, L
2
) read at “Prepara-
tion” into the screen.
If the lens was not replaced, give a check to the checkbox at
the lower left of the screen.
4) Click the [OK] button, and the adjustment data is then calcu-
lated from the sensor sensitivity value and the calculation re-
sult is written to the memory in the camera.
5) Upon successful completion of the data writing, the following
screen will appear. Check that the steady shot function oper-
ates normally.
Fig. 6-1-53
6-27
DSC-T10_ADJ
1-5.
LCD  SYSTEM  ADJUSTMENTS
1-5-1.
Function of Each Button on LCD System
Adjustment Screen
Click the [LCD SYSTEM ADJUSTMENT] button on the Main Menu
screen, and the “LCD SYSTEM ADJUSTMENT” screen in Fig.
6-1-54 will appear.
Fig. 6-1-54
1
[To Menu] button
The Main Menu screen comes back.
2
[Start] button
“LCD Adjustment” starts.
3
[Reset] button
This button functions same as the “Initialize” of the setup
screen.
4
[Release Data Setting] button
The data setting at the adjustment is cancelled.
During the data setting, the button color changes from “white”
to “red”. When the data setting is cancelled, the button color
returns to “white”.
(Use this button when an error occurred in the LCD adjust-
ment. If the adjustment completed successfully, the data set-
ting is automatically cancelled and the button color returns to
“white”.)
1-5-2.
Adjustment Items of LCD System Adjustment
The adjustment items of LCD system adjustment are as listed in
Table 6-1-4. The Automatic Adjustment Program executes the ad-
justment items if the LCD Adjustment Start button is clicked.
Button
Adjustment
Signal
Page
Address
Name
LCD
V-COM adj.
8F
11
Adjustment White Balance adj. Arbitrary 8F
42, 43, 58, 59
Table 6-1-4
4
3
2
1
Page of 37
Display

Click on the first or last page to see other DSC-T10 (serv.man4) service manuals if exist.