DOWNLOAD Sony DSC-S730 Service Manual ↓ Size: 1.73 MB | Pages: 16 in PDF or view online for FREE

1-1

DSC-S730

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.)

Note: When replacing the camera, erase the data in internal memory of the board before replacement.

Initializes the setting to the default setting.
Even if you execute this function, the images stored in the internal memory are retained.

1

Select [OK] with v on the control button, then press z.
The message "Initialize all settings Ready?" appears.

2

Select [OK] with v, then press z.
The settings are reset to the default setting.

Select [Cancel] in step 1 or 2, then press z.

Be sure not to power off the camera while initializing.

Copies all images in the internal memory to a "Memory Stick Duo".

1

Insert a "Memory Stick Duo" having sufficient free capacity.

2

Select [OK] with v on the control button, then press z.
The message "All data in internal memory will be copied Ready?" appears.

3

Select [OK] with v, then press z.
Copying starts. 

Select [Cancel] in step 2 or 3, then press z.

Use batteries with enough power remaining. If you attempt to copy image files using batteries with little 
remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data.
You cannot select images to copy.
The original images in the internal memory are retained even after copying. To delete the contents of the 
internal memory, remove the "Memory Stick Duo" after copying, then format the internal memory 
([Format] in [Internal Memory Tool]).
A new folder is created on the "Memory Stick Duo" and all the data will be copied to it. You cannot 
choose a specific folder and copy images to it.
The 

 (Print order) marks on the images are not copied.

This item does not appear when a "Memory Stick Duo" is inserted in the camera.

Formats the internal memory.

Note that formatting permanently erases all data in the internal memory, including even protected images.

1

Select [OK] with v on the control button, then press z.
The message "All data in internal memory will be erased Ready?" appears.

2

Select [OK] with v, then press z.
The format is complete.

Select [Cancel] in step 1 or 2, then press z.

2-1

DSC-S730

5

1

2

3

4

1

Open the BT LID

4

5

CABINET (REAR) ASSY

2

SCREW M 1.7 X 2.7

3

SCREW TP 1.7 X 4

SCREW TP 1.7 X 3.5

1

2

3

4

1

LCD

2

LCD PLATE

3

SCREW TP 1.4 X 3.5

4

SCREW TP 1.4 X 4

3

1

2

1

CABINET (FRONT) ASSY

2

SCREW TP 1.4 X 2.5

3

SCREW TP 1.4 X 3

1

2

3

1

BT LID SHAFT

2

BT LID

3

BT LID SPRING

Note : 
When CABINET(FRONT) ASSY is 
removed, the plate will bends if 
CABINET(FRONT) ASSY is inclined 
too much. 
Please remove CABINET (FRONT) 
ASSY as in parallel as possible.

plate

The following flow chart shows the disassembly procedure.

Ω

 

DSC-S730

2-2

The changed portions from
Ver. 1.0 are shown in blue.

Be careful about the Lens Assy.

Attach the Block assy protection sheet as shown.

Don't press the Sensor holder

Don't press the AF Motor

Keep clean these Pins.

Attach the Block assy 
protection sheet avoiding 
three screw holes.

Block assy
protection sheet

Don't press the Barrier part.

DSC-S730