Sony DSC-S3000 Service Manual ▷ View online
DSC-S3000
2-2
Wrap insulating tape.
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage
when the capacitor is handled by hand. The electric shock
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned
off. Therefore, the remaining voltage must be discharged as
described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end
of a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
DISCHARGING OF THE CHARGING CAPACITOR
Cut and remove the part of gilt
which comes off at the point.
(Be careful of that some
pieces of gilt may be left inside)
Note:
Note:
High-voltage cautions
High-voltage cautions
Discharging the Capacitor
Short-circuit from the outside of
the condenser poles with the short jig
about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit from the outside of
the condenser poles with the short jig
about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
DSC-S3000
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
DISASSEMBLY
1
#S1 X 1
2
BT Lid Open (
2
) → #S1 / #S2 X 6
5
#S3 X 5
1. Remove to numerical order (
1
to
5
) in the left figure.
Note
DISCHARGING OF THE CHARGING CAPACITOR
1
X-2580-972-1 FRONT COVER ASSY (S) (SILVER)
1
X-2580-973-1 FRONT COVER ASSY (B) (BLACK)
1
X-2580-974-1 FRONT COVER ASSY (P) (PINK)
2
A-1816-594-A SW BOARD, COMPLETE
3
X-2580-975-1 REAR COVER ASSY (S) (SILVER)
3
X-2580-976-1 REAR COVER ASSY (B) (BLACK)
3
X-2580-977-1 REAR COVER ASSY (P) (PINK)
4
4-276-727-01 SIDE COVER
#S1
3-113-005-01 SCREW TP 1.7*3 (Note)
#S2
4-277-180-01 SCREW TP 1.7*3 BK (Note)
#S3
3-113-001-01 SCREW TP 1.4*2.5
3
Note: THE COMBINATION OF CABINET’S COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer
to Table 2-1.
Table 2-1
Screw's
Ref. No. (Parts Color.)
Cabinet's Color
#S1 (Silver)
SILVER, PINK
#S2 (Black)
BLACK
Bottom View
#S1
#S1
#S2
(Note)
#S1
#S2
(Note)
#S3
#S1
#S1
#S2
(Note)
#S1
#S2
(Note)
2�
1
3
5�
2
4�
3
1�
4
2
ns
Main Frame Section
(See Page 2-4)
4(Claw)
ns
2(Claw)
#S1
#S2
(Note)
Left View
Right View
Front View
#S1
#S2
#S1
#S2
Bottom View
#S1
#S2
#S1
#S2
Open
BT Lid
Front View
#S3
DSC-S3000
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. MAIN FRAME SECTION
DISASSEMBLY
1. Remove to numerical order (
6
to
9
) in the left figure.
51
A-1816-596-A STROBE BLOCK ASSY
52
X-2580-981-1 TOP COVER ASSY
53
4-276-731-01 LCD BRACKET
54
1-811-402-11 LCD MODULE
55
(Note)
POLYESTER TAPE (BLACK)
#S4
3-288-943-01 SCREW_TP_1.4_3_A_0.2_D=2.5
#S5
3-277-533-01 TP_1.4_2.8_A0.3_D2.5_B
#S6
4-277-181-01 SCREW TP 1.4*2.3
6
#S5 X 2 → #S6 X 1
8
#S4 X 3
9
#S5 X 2
Top View
#S5
Left View
Top View
Back View
#S5
#S5
#S6
Back View
#S4
Note
Note: For the part (Ref.No.55), cut the Polyester Tape
(9-913-210-03) in the specified lengths.
For the specified length and attaching position, refer to
“Assembly-2: Polyester Tapes Attaching Method”.
6�
52
9�
51
8�
53
7�
54
55
(Note)
#S5
#S6
#S5
#S5
#S4
#S5
Main Board Section
(See Page 2-5)
(See Page 2-5)
DSC-S3000
2-5E
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-3. MAIN BOARD SECTION
ns: not supplied
DISASSEMBLY
1. Remove to numerical order (
0
to
qs
) in the left figure.
101
X-2580-978-1 MAIN FRAME ASSY
102
A-1816-599-A MAIN BOARD, COMPLETE
*
103
1-820-333-11 MULTI CONNECTOR (REC) 8P
104
1-542-878-11 MICROPHONE
105
1-858-616-11 SPEAKER (1.3CM)
106
A-1816-597-A CCD BLOCK ASSY (Note1, 2)
107
4-276-733-01 FILTER SET, LOW PASS
108
A-1816-598-A LENS BLOCK ASSY (Note3)
109
4-276-728-01 BATTERY DOOR (S) (SILVER)
109
4-276-729-01 BATTERY DOOR (B) (BLACK)
109
4-276-730-01 BATTERY DOOR (P) (PINK)
0
F1
1-576-363-11 FUSE, MICRO (1005 TYPE) (1A/30V)
0
F2
1-576-913-31 FUSE, MICRO (1608 TYPE) (1.6A/36V)
#S5
3-277-533-01 TP_1.4_2.8_A0.3_D2.5_B
#S7
3-277-534-01 TP_1.4_3.5_A0.3_D2.5_B
#S8
4-277-820-01 SCREW TP 1.4*3 BK
0
#S7 X 3
qa
#S5 X 1 → Unsolder
Note
Note3: Be careful about the Lens Block Assy.
Note1: To release the lock of the connector, gradually lift up the Lock plate in an order shown below to avoid damaging the Lock plate.
Don't press
the AF motor
Don't press the
Barrier part
Be careful of the Weld
Be careful of the weld
Don't press the
Sensor holder
Keep clean
these Pins
Back View
#S7
Solder
Back View
#S5
Note2: Refer to “Assembly-1: Connector Locking Method” when you
assemble.
11(Solder)
Solder
Solder
Solder
Claw
qs�
101
109
qa�
102
104
105
107
106
(Note1, 2)
0�
108
(Note3)
#S5
#S7
#S8
103
ns
ns
F1
F2
ns
1
2
3
Main Board
CCD Block Assy
CCD Block Assy
Flexible Board
Lock plate
Click on the first or last page to see other DSC-S3000 service manuals if exist.