Sony DSC-S3000 (serv.man2) Service Manual ▷ View online
DSC-S3000_ADJ
5-5
5-2-2. Zoom Adjustment
The Zoom Over Run/Focus Back Lash Adjustment order is as follows.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
The adjustment finished normally.
O Zoom Station Passed
Fig. 5-2-15
The adjustment is complete
The adjustment is finished abnormally.
X Focus backlash NG
X Zoom Adjust NG
X Zoom Adjust NG
Fig. 5-2-16
Malfunction of Zoom adjust-
ment result
X Focus backlash NG
Fig. 5-2-17
Malfunction of Zoom adjust-
ment Focus section
X Zoom Adjust NG
Fig. 5-2-18
Malfunction of Zoom adjust-
ment Zoom section
Adjustment order
Screen display
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in the horizontal plane.
Press the control button “ V (Key Down)”, then Zoom Adjustment starts.
on the screen. (Fig. 5-2-15)
In case of the adjustment is finished normally,
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-16 to 5-2-18)
In this case, confirm the adjusting environment
and readjust.
5-2-3. Far Focus Adjustment
Note:
When using the Flange back adjustment jig, take care of the following points:
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1) Install the Flange back adjustment jig so that the distance between
it and the front of lens of camera is 3 cm or less.
Note:
Take care not to hit the Flange back adjustment jig when extend-
ing the lens.
2) Make the height of Flange back adjustment jig and the camera equal.
3) Check that the center of chart meets the center of shot image screen
with the zoom lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Far Focus Station Passed
Please Key MENU Enter...
Please Key MENU Enter...
Fig. 5-2-20
The adjustment is complete
The adjustment is finished abnormally.
X Far Focus NG !
Please ReAdjust Far Focus
Please ReAdjust Far Focus
Fig. 5-2-21
Malfunction of Far Focus adjust-
ment
Adjustment order
Screen display
Fig. 5-2-19
3 cm or less
Equipment required: Flange back adjustment jig
Flange back adjustment jig
Camera
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flange back adjustment jig. (Fig. 5-2-19)
Press the control button “ b (Key Left)”, then Far Focus Adjustment starts.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-20)
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-21)
In this case, confirm the adjusting environment
and readjust.
DSC-S3000_ADJ
5-6
5-2-4. Near Focus Adjustment
Note:
Perform the Near Focus Adjustment after the Far Focus Adjustment.
1) Be sure to set 50 ± 1 cm distance between the chart and the tip of camera lens.
2) Check that the center of chart meets the center of shot image screen with the zoom
lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Near Focus Station Passed
Please Key MENU Enter...
Please Key MENU Enter...
Fig. 5-2-23
The adjustment is complete
The adjustment is finished abnormally.
X Near Focus NG !
Please ReAdjust Far Focus
Please ReAdjust Far Focus
Fig. 5-2-24
Malfunction of Near Focus ad-
justment
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Chart. (Fig. 5-2-22)
Press the control button “ B (Key Right)”, then Near Focus Adjustment starts.
on the screen. (Fig. 5-2-23)
In case of the adjustment is finished normally,
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
(Fig. 5-2-24)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
In this case, confirm the adjusting environment
and readjust.
In case of the Near Focus adjustment is failed,
readjust the Far Focus adjustment and try to
readjust the Near Focus adjustment.
Screen display
5-2-5. White Balance Adjustment
The White Balance Adjustment is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
The adjustment finished normally.
O WB OK
Fig. 5-2-26
The adjustment is complete
The adjustment is finished abnormally.
X Cap WB NG
Fig. 5-2-27
Malfunction of Cap White Bal-
ance adjustment
X Pre WB NG
Fig. 5-2-28
Malfunction of Pre White Bal-
ance adjustment
X WB NG
Fig. 5-2-29
Malfunction of White Balance
adjustment
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-2-25)
Press the control button “ z (Key OK)”, then White Balance Adjustment starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-26)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-27 to 5-2-29)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Screen display
Fig. 5-2-22
Chart
Camera
Equipment required: Chart
50 ± 1 cm
Fig. 5-2-25
Equipment required: Small pattern box (PTB-1450)
Small pattern box
(PTB-1450)
Camera
0.5 to 1.0 cm
DSC-S3000_ADJ
5-7E
Selectable language table
5-2-6. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the SD-Card or Memory Stick PRO Duo being used.
The content of “lang.txt” is as follows:
Language Destination (for example: E32) (enter key)
Product ID (10 bit) (enter key) (refer to “5-3. PRODUCT ID LIST”)
S/N (7 bit) (enter key)
The following is an example of E32 Language Destination Setting for DSC-S3000 Silver camera.
E32
0048886110
0120243
Especially Attention:
1). The enter key must be the end symbol of each row.
2). For the Product ID, refer to “5-3. PRODUCT ID LIST”, and the Product ID must be 10 bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3). The S/N must be 7 bit. It refers to the serial number of shipment.
The adjustment is finished abnormally.
Read Language NG!
Fig. 5-2-31
Malfunction of Set Language
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the Shutter button (Key S1), then Language Destination Setting starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-30)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-31)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
Screen display
DESTINA
TION
AREA
SELECTABLE LANGUAGE
VIDEO OUT
Default
Japanese
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
Traditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
Turkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
Vietnamese
Ukrainian
CA2
CND
z
a
a
a
a
NTSC
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
E37
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
AU2
AUS
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
KR2
KR
a
a
a
a
a
a
a
a
z
a
a
a
a
a
NTSC
BR4
BR
a
a
a
a
z
a
a
a
a
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
5-3. PRODUCT ID LIST
DSC-S3000
Area
Color
Product ID
E37
Silver
48886106
Black
48886107
Pink
48886108
E32
Silver
48886110
Black
48886170
Pink
48886186
E33
Silver
48886111
Black
48886171
Pink
48886187
CA2
Silver
48886140
CEE8
Silver
48886150
Black
48886163
Pink
48886193
CEE2
Silver
48886152
Black
48886165
BR4
Silver
48886154
Pink
48886197
KR2
Silver
48886180
Black
48886181
Pink
48886182
AU2
Silver
48886190
Black
48886191
Pink
48886192
The adjustment finished normally.
Encryption:
Set LangDestination OK!
Fig. 5-2-30
The adjustment is complete
Note:
The screen above is an example.
Note:
The screen above is an example.
DSC-S3000_ADJ
5-7E
Selectable language table
5-2-6. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the SD-Card or Memory Stick PRO Duo being used.
The content of “lang.txt” is as follows:
Language Destination (for example: E32) (enter key)
Product ID (10 bit) (enter key) (refer to “5-3. PRODUCT ID LIST”)
S/N (7 bit) (enter key)
The following is an example of E32 Language Destination Setting for DSC-S3000 Silver camera.
E32
0048886110
0120243
Especially Attention:
1). The enter key must be the end symbol of each row.
2). For the Product ID, refer to “5-3. PRODUCT ID LIST”, and the Product ID must be 10 bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3). The S/N must be 7 bit. It refers to the serial number of shipment.
The adjustment is finished abnormally.
Read Language NG!
Fig. 5-2-31
Malfunction of Set Language
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the Shutter button (Key S1), then Language Destination Setting starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-30)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-31)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
Screen display
DESTINA
TION
AREA
SELECTABLE LANGUAGE
VIDEO OUT
Default
Japanese
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
Traditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
Turkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
Vietnamese
Ukrainian
CA2
CND
z
a
a
a
a
NTSC
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
E37
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
AU2
AUS
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
KR2
KR
a
a
a
a
a
a
a
a
z
a
a
a
a
a
NTSC
BR4
BR
a
a
a
a
z
a
a
a
a
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
5-3. PRODUCT ID LIST
DSC-S3000
Area
Color
Product ID
E37
Silver
48886106
Black
48886107
Pink
48886108
E32
Silver
48886110
Black
48886170
Pink
48886186
E33
Silver
48886111
Black
48886171
Pink
48886187
CA2
Silver
48886140
CEE8
Silver
48886150
Black
48886163
Pink
48886193
CEE2
Silver
48886152
Black
48886165
BR4
Silver
48886154
Pink
48886197
KR2
Silver
48886180
Black
48886181
Pink
48886182
AU2
Silver
48886190
Black
48886191
Pink
48886192
The adjustment finished normally.
Encryption:
Set LangDestination OK!
Fig. 5-2-30
The adjustment is complete
Note:
The screen above is an example.
Note:
The screen above is an example.
Display
