DOWNLOAD Sony DSC-RX100M3 (serv.man3) Service Manual ↓ Size: 9.21 MB | Pages: 31 in PDF or view online for FREE

DSC-RX100M3_L2

1-10

5.  Remove the Z Seal.

 

Z Seal

6.  Pull out the Reset PI on the LF-2091 Flexible Board.

 

Reset PI

7.  Remove LF-2091 Flexible Board from the hook and the boss of the Rear Tube Mirror Block Assy

 

1

 Hook

2

 Boss

8.  Disconnect the F Flexible Board from the connector of the LF-2091 Flexible Board.

 

LF-2091 Flexible Board

Connector

Stationary Tube

F Flexible Board

9.  Remove the LF-2091 Flexible Board from the hook of the Rear Tube Mirror Block Assy.

 

Hook

10. Remove the LF-2091 Flexible Board from the hook and the boss of the Stationary Tube.

 

Boss

Hook

11.  Remove the Focus FPC Retainer.

 

Focus FPC Retainer

12. Disconnect the two flexible boards (SS and SH) from the connectors of the LF-2091 Flexible Board.

 

SS flexible board

SH flexible board

13. Remove the connector part of the LF-2091 Flexible Board from the holes of the Stationary Tube.

 

Holes

Holes

DSC-RX100M3_L2

1-11

14. Remove the five screws to detach the Rear Tube Mirror Block Assy.

 

Rear Tube Mirror Block Assy

15. Remove the Lubricating Block Assy (B), the Gear A Lubricated Assy and the Wheel Lubricating Block Assy.

 

Lubricating Block Assy (B)

Gear A Lubricated Assy

Wheel Lubricating Block Assy

16. Insert a Lubricating Block Assy (B)* and turn it clockwise to the maximum extent.
 

*) Use a Lubricating Block Assy (B) that was not installed in the unit.

 

Lubricating Block Assy (B)

17. Pull out the two flexible boards (SS and SH) from the Stationary Tube.

 

Stationary Tube

SS flexible board

SH flexible board

18. Turn the Lubricating Block Assy (B)* counterclockwise to the maximum extent, and detach the Lubricating Block Assy (B).
 

*) Use a Lubricating Block Assy (B) that was not installed in the unit.

 

Lubricating Block Assy (B)

19. Remove the 1st/2nd/3rd group assy from the Stationary Tube. And remove the two screws to detach the DC Motor Worm Assy.

 

Stationary Tube

DC Motor Worm Assy

1st/2nd/3rd group assy

20. Turn the Straight Tube Block Assy counterclockwise and remove it from the 1st/2nd/3rd group assy.

 

Straight Tube Block Assy

Straight Tube
Block Assy

1st/2nd/3rd group assy

21. Remove the 1 Group Frame Block Assy from the 2nd/3rd group assy.

 

1 Group Frame Block Assy

2nd/3rd group assy

DSC-RX100M3_L2

1-12

1.  Match the 1st Group Press Block of the 1 Group Frame Block Assy with the cabinet number of the 3 Group Frame Block Assy and install the 1 

Group Frame Block Assy while turning it clockwise.

Note 1:  If Ornamental Ring (A) and Barrier Block Assy is installed to 1 Group Frame Block Assy, remove them first.
Note 2:  Be careful not to lose the 1st Group Press Block.
Note 3:  When installing the 1 Group Frame Block Assy, stop turning it when the convex parts of the 1st Group Press Block and the 3 Group Frame Block Assy 

match.

 

1st Group Press Block

3 Group Frame Block Assy

Cavity number

1 Group Frame Block Assy

2.  Install the Straight Tube Block Assy matching its cabinet number with the flexible boards position of the 3 Group Frame Block Assy.

 

Cavity number

Straight Tube Block Assy

Flexible boards

1st/2nd/3rd group assy

Gap

3.  After turning the Straight Tube Block Assy counterclockwise about eight degrees to fully install it, turn the Straight Tube Block Assy clockwise 

to the maximum extent to fit the bayonet.

 

Straight Tube Block Assy

About 8

°

4  Attach the DC Motor Worm Assy and tighten two screws. And install the 1st/2nd/3rd group assy to the Stationary Tube matching the phase marks 

as shown in the figure.

Note 1:  When installing this assy, confirm that the convex parts of the 3 Group Frame Block Assy, 1 Group Frame Block Assy and the Cam Tube are shown below.
Note 2:  Confirm that the straight key of the 3 Group Frame Block Assy is fit in the groove of the Stationary Tub. If the straight key is not fit in the groove, repeat 

these steps from step 1.

 

1st/2nd/3rd group assy

3 Group Frame Block Assy

Straight Tube Block Assy

Cam Tube

Convex parts

Gear end

Straight Tube Block Assy

Stationary Tube

Fit to groove

DC Motor 
Worm Assy

5.  Install the Lubricating Block Assy (B)* and turn it clockwise to the maximum extent.
 

*) Use a Lubricating Block Assy (B) that was not installed in the unit.

 

Lubricating Block Assy (B)

6.  Pass the two flexible boards through the holes in the Stationary Tube.

 

Stationary Tube

SS flexible board

SH flexible board

7.  Turn the Lubricating Block Assy (B)* counterclockwise to the maximum extent.
 

*) Use a Lubricating Block Assy (B) that was not installed in the unit.

 

Lubricating Block Assy (B)

DSC-RX100M3_L2

1-13

8.  Install the Wheel Lubricating Block Assy, the Gear A Lubricated Assy and the Lubricating Block Assy (B).

 

Lubricating Block Assy (B)

Gear A Lubricated Assy

Wheel Lubricating Block Assy

9.  Attach the Rear Tube Mirror Block Assy and tighten five screws in numerical order in the following figure.

 

Rear Tube Mirror Block Assy

1

4

5

3

2

10. Install the connector part of the LF-2091 Flexible Board to the holes of the Stationary Tube.

 

Holes

Holes

11.  Connect the flexible boards (SS and SH) to the connectors of the LF-2091 Flexible Board.

 

SS flexible board

SH flexible board

12. Install the Focus FPC Retainer.

 

Focus FPC Retainer

13. Install the LF-2091 Flexible Board to the hook and the boss of the Stationary Tube.

 

Boss

Hook

14. Install the LF-2091 Flexible Board to the hook of the Rear Tube Mirror Block Assy.

 

Hook

15. Connect the F Flexible Board to the connector of the LF-2091 Flexible Board.

 

LF-2091 Flexible Board

Connector

Stationary Tube

F Flexible Board