DOWNLOAD Sony DSC-RX100M3 (serv.man2) Service Manual ↓ Size: 9.1 MB | Pages: 31 in PDF or view online for FREE

Model
DSC-RX100M3 (serv.man2)
Pages
31
Size
9.1 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / - LEVEL 2
File
dsc-rx100m3-sm2.pdf
Date

Sony DSC-RX100M3 (serv.man2) Service Manual ▷ View online

DSC-RX100M3_L2
– 2 –
SPECIFICATIONS
– ENGLISH –
– JAPANESE –
Camera 
[System] 
Image device: 13.2 mm × 8.8 mm
 
(1.0 type) Exmor R™ CMOS
 sensor
Total pixel number of camera:
 
Approx. 20.9 Megapixels
Effective pixel number of camera:
 
Approx. 20.1 Megapixels
Lens: ZEISS Vario-Sonnar T 2.9×
 zoom 
lens
 
f = 8.8 mm – 25.7 mm (24 mm –
 
70 mm (35 mm film equivalent))
 
F1.8 (W) – F2.8 (T)
 
While shooting movies (16:9):
 
25.5 mm – 74 mm
*1
 
While shooting movies (4:3):
 
31 mm – 90 mm
*1
 
*1
 When [
 SteadyShot] is set to [Standard]
SteadyShot: Optical
File format:
 
Still images: JPEG (DCF, Exif,
 
MPF Baseline) compliant, RAW
 
(Sony ARW 2.3 Format), DPOF
 compatible
 
Movies (XAVC S format):
 
MPEG-4 AVC/H.264 XAVC S
 
ver.1.0 format compliant
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Linear PCM 2ch (48 kHz
 16 
bit)
 
Movies (AVCHD format):
 
AVCHD format Ver. 2.0
 compatible
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Dolby Digital 2ch,
 
equipped with Dolby Digital Stereo
 Creator
•  Manufactured under license from 
Dolby Laboratories.
 
Movies (MP4 format):
 Video: 
MPEG-4 
AVC/H.264
 
Audio: MPEG-4 AAC-LC 2ch
Recording media: Memory Stick PRO
 
Duo media, Memory Stick Micro
 
media, SD cards, microSD memory
 cards
Flash: Flash range (ISO sensitivity
 
(Recommended Exposure Index)
 set 
to 
Auto):
 
Approx. 0.4 m to 10.2 m
 
(1.31 ft. to 33.46 ft.) (W)/
 
Approx. 0.4 m to 6.5 m
 
(1.31 ft. to 21.33 ft.) (T)
[Input and Output connectors]
HDMI connector: HDMI micro jack
Multi/Micro USB Terminal*:
 USB 
communication
USB communication: Hi-Speed USB
 (USB 
2.0)
* Supports Micro USB compatible device.
[Viewfinder]
Type: Electronic viewfinder (Organic
 Electro-Luminescence)
Total number of dots:
 
1 440 000 dots
Frame coverage: 100%
Magnification: Approx. 0.59 ×
 
(35 mm-format equivalent) with 
50 mm lens at infinity, –1 m
–1
Eye point: Approx. 20 mm from the
 
eyepiece, 19.2 mm from the
 
eyepiece frame at –1 m
–1
* Diopter adjustment:
 –4.0 
m
–1
 to +3.0 m
–1
[Monitor]
LCD monitor:
 
7.5 cm (3.0 type) TFT drive
Total number of dots:
 
1 228 800 dots
[Power, general]
Power: Rechargeable battery pack
 NP-BX1, 
3.6 
V
 
AC Adaptor AC-UB10C/UB10D,
 5 
V
Power consumption:
 
Approx. 1.7 W (during shooting
 
with the monitor)
 
Approx. 2.3 W (during shooting
 
with the viewfinder)
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
 
(–4 °F to +140 °F)
Dimensions (CIPA compliant):
 
101.6 mm × 58.1 mm × 41.0 mm
 
(4 inches × 2 3/8 inches ×
 
1 5/8 inches) (W/H/D)
Mass (CIPA compliant) (Approx.):
 
290 g (10.2 oz) (including NP-BX1
 
battery pack, Memory Stick PRO
 Duo 
media)
Microphone: Stereo
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
 Compatible
[Wireless LAN]
Supported standard: IEEE 802.11 b/g/n
Frequency: 2.4GHz
Supported security protocols: WEP/
 WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
 
Protected Setup) / manual
Access method: Infrastructure Mode
NFC: NFC Forum Type 3 Tag
 compliant
Model No. WW808161
AC Adaptor AC-UB10C/UB10D
Power requirements: AC 100 V to
 
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Rechargeable Battery Pack
NP-BX1
Battery type: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 1.89 A
Capacity: Typical 4.5 Wh (1 240 mAh)
Design and specifications are subject to
change without notice.
Model information table
Model
DSC-RX100M3
Destination
US, CND, E, KR, J
AEP, UK, RU, E, HK, CH, JE
Color system
NTSC
PAL
GPS
Wi-Fi
NFC
• Abbreviation
  CH :  Chinese model
  CND :  Canadian model
  HK :  Hong Kong model
  J : 
Japanese model
  JE : 
Tourist model
  KR :  Korea model
 RU  : 
Russian 
model
概略仕様
本体
[システム]
撮像素子:
13.2 mm
×
8.8 mm
1.0
型)
 Exmor 
R
TM
 CMOS
センサー
総画素数:約
2090
万画素
カメラ有効画素数:約
2010
万画素
レンズ:
 ZEISS 
バリオ・ゾナー
T*
 2.9
倍ズームレンズ
 f=8.8 
mm
 
25.7 mm
 
24 
mm
 
 70 mm
35 mm
フィルム
 
換算値))、
F1.8 (W) 
 F2.8 (T)
 
動画撮影時(
16
9
):
 25.5 
mm
 
 74 mm
*1
 
動画撮影時(
4
3
):
 31 
mm
 
 90 mm
*1
*1
 
 
手ブレ補正]が[スタンダード]のとき
手ブレ補正:光学式
記録方式:
 
静止画記録方式:
 JPEG
DCF
Exif
MPF Baseline
)準拠、
 RAW
(ソニー
ARW 2.3
フォーマット)、
 DPOF
対応
 
動画記録方式(
XAVC S
方式):
 
MPEG-4 AVC/H.264 XAVC S ver.1.0
 
規格準拠
 
映像:
MPEG-4 AVC/H.264
 
音声:リニア
PCM 2ch
48kHz 16bit
 
動画記録方式(
AVCHD
方式):
 AVCHD
規格
 Ver.2.0
準拠
 
映像:
MPEG-4 AVC/H.264
 
音声:
Dolby Digital 2ch
 
ドルビーデジタルステレオクリエーター搭載
 
ドルビーラボラトリーズからの実施権に基づ
き製造されています。
 
動画記録方式(
MP4
方式):
 
映像:
MPEG-4 AVC/H.264
 
音声:
MPEG-4 AAC-LC 2ch
記録メディア:
 
メモリースティック
 PRO 
デュオ、
メモリースティック
 
マイクロ、
SD
カード、
microSD 
メモリーカード
フラッシュ:撮影範囲(
ISO
感度(推奨露光
 
指数)がオートのとき)
 
0.4 
m∼約
10.2 m (W)/
 
0.4 
m∼約
6.5 m (T)
[入出力端子]
HDMI
端子:
HDMI
マイクロ端子
マルチ
/
マイクロ
USB
端子
*
USB
通信
USB
通信:
Hi-Speed USB
USB 2.0
この端子にはマイクロ
USB
規格に対応した機器をつ
なぐことができます。
[ファインダー]
形式:電子式ビューファインダー(有機
EL
総ドット数:
1 440 000
ドット
視野率:
100
倍率:約
0.59
倍(
35mm
判換算、
50 mm
レンズ、
 
無限遠、視度−
1 m
−1
時)
アイポイント:最終光学面から約
20 mm
 
接眼枠から約
19.2 
mm(視度−
1 m
−1
時)
視度調整:−
4.0 m
−1
∼+
3.0 m
−1
[モニター]
液晶モニター:
 7.5 
cm
3.0
型)、
TFT
駆動
総ドット数:
1 228 800
ドット
[電源・その他]
電源:リチャージャブルバッテリーパック
 NP-BX1
3.6 V
 AC
アダプター
 AC-UB10C/UB10D
 5 
V
消費電力:
 
1.7 W
(モニターで撮影時)
 
2.3 W
(ファインダーで撮影時)
動作温度:
℃∼
40 
保存温度:−
20 
℃∼
+60 
外形寸法(
CIPA
準拠)
(約):
 101.6 
mm
×
58.1 mm
×
41.0 mm
 
(幅×高さ×奥行き)
本体質量(
CIPA
準拠)
(約):
 290 
g
(バッテリー
NP-BX1
 
メモリースティック
 PRO 
デュオを含む)
マイクロホン:ステレオ
スピーカー:モノラル
Exif Print
:対応
PRINT Image Matching III
:対応
[ワイヤレスLAN]
対応規格:
IEEE 802.11b/g/n
使用周波数帯:
2.4GHz
セキュリティー:
WEP/WPA-PSK/
 WPA2-PSK
接続方式:
WPS
Wi-Fi Protected Setup
 
/
マニュアル
アクセス方式:インフラストラクチャーモード
NFC
NFC
フォーラム
 Type 3 Tag
準拠
Model No. WW808161
ACアダプター
AC-UB10C/UB10D
定格入力:
AC 100 V
240 V
 
50 Hz/60 Hz
70 mA
定格出力:
DC 5 V
0.5 A
リチャージャブルバッテリー
パックNP-BX1
使用電池:リチウムイオン電池
最大電圧:
DC 4.2 V
公称電圧:
DC 3.6 V
容量:
4.5 Wh
1 240 mAh
本機や付属品の仕様および外観は、改良のため予告
なく変更することがありますが、ご了承ください。
DSC-RX100M3_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•   Set the soldering iron tip temperature to 350 °C approximately. 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
Caution:  The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!  
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•   Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Set the soldering iron tip temperature to 350 °C approximately.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図,部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにして下さい。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認して下さい。
5.  チップ部品交換時の注意
 
・  取外した部品は再使用しないで下さい。
 
・  タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6.  フレキシブルプリント基板の取扱いについて
 
・  半田こてのこて先温度は約350℃に設定してください。
 
・  同一パターンに何度もコテ先を当てないで下さい。(3回
以内)
 
・  パターンに力が加わらないよう注意して下さい。
サービス,点検時には次のことにご注意ください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・  半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
注意:  半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
・  半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
– ENGLISH –
– JAPANESE –
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
DSC-RX100M3_L2
1-1
1. SERVICE  NOTE
1-1.  PRECAUTION ON REPLACING THE SY-1036 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data. 
The data getting for this model is as follows.
• PRODUCT ID & USB SERIAL No. INPUT
• Lens data carry
• AWB adj
• Light sensor adj
• Eye sensor adj
• EVF Data Input
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB 
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference from 
the ID registered by the customer.
Update of MAC Address
When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the IC’s unique number (MAC ad-
dress) must be reloaded.
Perform the following procedure to reload the IC’s unique number (MAC address).
1.  Download the latest-version Adjust Manual.
2.  Install the downloaded Adjust Manual.
3.  Start the Adjust Manual, and execute “Wireless LAN check” on the ADJUST tab.
4.  Perform the following operations for the unit to initialize.
 MENU 
→   → [Reset Network Set.] → [OK] → ●
5.  Perform the following operations for the unit to display MAC address.
 MENU 
→   → [Disp MAC Address] → ●
6.  Confirm that the displayed MAC address has been updated.
Applicable parts
•  SY-1036 BOARD, COMPLETE (SERVICE)
 
Note: The LOAD AND WRITE function in ADJUSTMENT DATA BACKUP on the DATA tab in the Adjust manual overwrites all data of the unit.
 
Therefore, the MAC address updated during the above procedure is also overwritten.
Perform the above operations after all work has been done.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the 
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
– ENGLISH –
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE7701).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity ADJ”.
Type A:
Type B:
P Y
P Y
P: PITCH sensor sensitivity
Y: YAW sensor sensitivity
SY-1036 BOARD (SIDE A)
SE7701
Note: The sensor sensitivity of SE7701 of SY-1036 board is written only repair parts.
1-2.  NOTES ON REPLACING THE LENS
When replacing the lens, read the QR code of the repair lens.
To read the QR code, start the Adjust manual and press the QR code reader button.
The read data is used in the following processes.
•  Selection of Spacer Plate when mounting the imager board
•  Adjustment after replacing the lens
1-2-1.
 
Selection of Spacer Plate when Mounting the Imager Board
1.  Load the Spacer Plate on the QR code reader screen.
2.  The thickness of the Spacer Plate to be loaded is displayed.
 
3.  Select the Spacer Plate according to the instructions on the screen and mount the imager board.
1-2-2.
 
Adjustment after Replacing the Lens
Perform LOAD from “Lens data carry” on the ADJUST tab in the Adjust manual.
QR code
DSC-RX100M3_L2
1-2
– ENGLISH –
1-3.  NOTES ON REMOVING/INSTALLING THE IMAGER BOARD (CD-847 FLEXIBLE BOARD)
When the CD-847 Flexible Board (Imager) is mounted to the lens, shift and tilt adjustment is made with Spacer Plates.
When removing the CD-847 Flexible Board, pay attention to the following.
(1)  When the lens is not replaced
 
Example: In the case of disassembly, cleaning, or replacement of the CD-847 Flexible Board (Imager)
•  Check and record the size of the built-in three Spacer Plates and store them so as not to lose them.
•  When assembling the CD-847 Flexible Board, be sure to install the Spacer Plates to their original locations.
Size
0.xx
Note
Be careful not to lose the Spacer Plates.
If any Spacer Plate is lost or their previous positions are not sure, repeatedly take a photo and check that there is no local defocus. 
Selecting appropriate Spacer 
Plates
 is needed.
(2)  When the lens is replaced
 
Refer to “1-2. NOTES ON REPLACING THE LENS” for select Spacer Plates and install them to the new lens.
1-4.  NOTES FOR REPLACING THE EVF DISPLAY DEVICE (LCD902) OR THE SY-1036 BOARD
Adjustment values of each EVF display device (LCD902) are stored on the SY board.
Therefore, when the LCD902 or the SY board has been replaced, write adjustment values.
White balance value
Brightness value
2565687041A
Example of the label which is put on repairing EVF display device (LCD902)
Note:  When a label is mention such as the illustration, please read it follows.
 
Brightness value: 256
 
White balance value: 874
When LCD902 is replaced:
1.  Check and write down the adjustment values printed on the repairing EVF display device (LCD902) label.
2.  After the LCD902 has been replaced, execute “EVF Data Input” on the ADJUST tab by using the Adjust manual to write the adjustment values.
When replacing SY board (in case adjustment values can be read):
1.  In case the unrepaired unit starts and adjustment values can be read by using the Adjust manual, execute “ADJUSTMENT DATA BACKUP” on 
the DATA tab.
2.   After the SY board has been replaced with a SY board for repair, execute “ADJUSTMENT DATA BACKUP” on the DATA tab of the Adjust 
manual to write the extracted data to the unit.
When replacing SY board (in case adjustment values cannot be read):
Consult with each Head Quarters.
Page of 31
Display

Sony DSC-RX100M3 (serv.man2) Service Manual ▷ Download

  • DOWNLOAD Sony DSC-RX100M3 (serv.man2) Service Manual ↓ Size: 9.1 MB | Pages: 31 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DSC-RX100M3 (serv.man2) in PDF for free, which will help you to disassemble, recover, fix and repair Sony DSC-RX100M3 (serv.man2) Digital Camera. Information contained in Sony DSC-RX100M3 (serv.man2) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.