Sony DSC-RX10 (serv.man2) Service Manual ▷ View online
DSC-RX10_L2
– 2 –
SPECIFICATIONS
概略仕様
– ENGLISH –
– JAPANESE –
Camera
[System]
Image device: 13.2 mm × 8.8 mm
(1.0 type) Exmor R CMOS sensor
Total pixel number of camera:
Approx. 20.9 Megapixels
Effective pixel number of camera:
Approx. 20.2 Megapixels
Lens: Carl Zeiss Vario-Sonnar T* 8.3×
zoom
zoom
lens
f = 8.8 mm – 73.3 mm (24 mm –
200 mm (35 mm film equivalent))
F2.8
While shooting movies (16:9):
26 mm – 212 mm
*1
While shooting movies (4:3):
31 mm – 259 mm
*1
*1
When [
SteadyShot] is set to
[Standard]
SteadyShot: Optical
Exposure control: Automatic exposure,
Exposure control: Automatic exposure,
Aperture priority, Shutter priority,
Manual exposure, Scene Selection
White balance: Automatic, Daylight,
Shade, Cloudy, Incandescent,
Fluorescent
(Warm
White/
Cool White/Day White/Daylight),
Flash, Color temperature/Color
filter,
Custom
File format:
Still images: JPEG (DCF, Exif,
MPF Baseline) compliant, RAW
(Sony ARW 2.3 Format), DPOF
compatible
Movies (AVCHD format):
AVCHD format Ver. 2.0
compatible
Video:
Video:
MPEG-4
AVC/H.264
Audio: Dolby Digital 2ch,
equipped with Dolby Digital Stereo
Creator
• Manufactured under license from Dolby
Laboratories.
Movies (MP4 format):
Video:
MPEG-4
AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
Recording media: “Memory Stick PRO
Duo” media, “Memory Stick
Micro” media, SD cards, microSD
memory
cards
Flash: Flash range (ISO sensitivity
(Recommended Exposure Index)
set
to
Auto):
Approx. 1.0 m to 10.2 m
(3.28 ft. to 33.46 ft.)
[Input and Output connectors]
HDMI connector: HDMI micro jack
Multi Terminal*:
USB
Multi Terminal*:
USB
communication
USB communication: Hi-Speed USB
(USB
(USB
2.0)
Microphone jack:
φ3.5 mm Stereo
mini
jack
Headphones jack:
φ3.5 mm Stereo
mini
jack
* Supports Micro USB compatible device.
[Viewfinder]
Type: Electronic viewfinder
Total number of dots:
Total number of dots:
1 440 000 dots
Frame coverage: 100%
Magnification: 0.70 × (35 mm-format
Magnification: 0.70 × (35 mm-format
equivalent) with 50 mm lens at
infinity, –1 m
–1
(diopter)
Eye point: Approx. 23 mm from the
eyepiece, 21.5 mm from the
eyepiece frame at –1 m
–1
(diopter)
Diopter adjustment:
–4.0
–4.0
m
–1
to +3.0 m
–1
(diopter)
[Screen]
LCD screen:
7.5 cm (3.0 type) TFT drive
Total number of dots:
1 228 800 dots
[Power, general]
Power: Rechargeable battery pack
NP-FW50,
NP-FW50,
7.2
V
AC Adaptor AC-UB10/UB10B/
UB10C/UB10D,
5
V
Power consumption:
Approx. 2.1 W (during shooting
with the LCD screen)
Approx. 2.7 W (during shooting
with the viewfinder)
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (CIPA compliant):
129.0 mm × 88.1 mm × 102.2 mm
(5 1/8 inches × 3 1/2 inches ×
4 1/8 inches) (W/H/D)
Mass (CIPA compliant) (Approx.):
813 g (1 lb 12.7 oz) (including NP-
FW50 battery pack, “Memory
Stick PRO Duo” media)
Microphone: Stereo
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
Compatible
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III:
Compatible
[Wireless LAN]
Supported standard: IEEE 802.11 b/g/n
Frequency: 2.4GHz
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Frequency: 2.4GHz
Supported security protocols: WEP/
WPA-PSK/WPA2-PSK
Configuration method: WPS (Wi-Fi
Protected Setup) / manual
Access method: Infrastructure Mode
NFC: NFC Forum Type 3 Tag
compliant
NFC: NFC Forum Type 3 Tag
compliant
AC Adaptor AC-UB10/UB10B/
UB10C/UB10D
UB10C/UB10D
Power requirements: AC 100 V to
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Operating temperature: 0 °C to 40 °C
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Dimensions (Approx.):
50 mm × 22 mm × 54 mm
(2 inches × 7/8 inches ×
2 1/4 inches) (W/H/D)
Rechargeable Battery Pack
NP-FW50
NP-FW50
Battery type: Lithium-ion battery
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions (Approx.):
31.8 mm × 18.5 mm × 45 mm
(1 5/16 inches × 3/4 inches ×
1 13/16 inches) (W/H/D)
Design and specifications are subject to change
without notice.
without notice.
本体
[システム]
撮像素子:
13.2 mm
×
8.8 mm
(
1.0
型)
Exmor R CMOS
センサー
総画素数:約
2090
万画素
カメラ有効画素数:約
2020
万画素
レンズ:
カール
ツァイス
バリオ・ゾナー
T*
8.3
倍ズームレンズ
f=8.8
mm
∼
73.3 mm
(
24
mm
∼
200 mm
(
35 mm
フィルム換算値))、
F2.8
動画撮影時(
16
:
9
):
26
mm
∼
212 mm*
1
動画撮影時(
4
:
3
):
31
mm
∼
259 mm*
1
*
1
[
手ブレ補正]が[スタンダード]のとき
手ブレ補正:光学式
露出制御:自動、絞り優先、シャッタースピード優先、
露出制御:自動、絞り優先、シャッタースピード優先、
マニュアル露出、シーンセレクション
ホワイトバランス:オート
/
太陽光
/
日陰
/
曇天
/
電球
/
蛍光灯(温白色
/
白色
/
昼白色
/
昼光色)
/
フラッシュ
/
色温度・カラーフィルター
/
カスタム
記録方式:
静止画記録方式:
JPEG
(
DCF
、
Exif
、
MPF Baseline
)準拠、
RAW
(ソニー
ARW 2.3
フォーマット)、
DPOF
対応
動画記録方式(
AVCHD
方式):
AVCHD
規格
Ver.2.0
準拠
映像:
MPEG-4 AVC/H.264
音声:
Dolby Digital 2ch
ドルビーデジタルステレオクリエーター搭載
•
ドルビーラボラトリーズからの実施権に基づ
き製造されています。
き製造されています。
動画記録方式(
MP4
方式):
映像:
MPEG-4 AVC/H.264
音声:
MPEG-4 AAC-LC 2ch
記録メディア:
“メモリースティック
PRO
デュオ”、
“メモリースティック
マイクロ”、
SD
カード、
microSD
メモリーカード
フラッシュ:撮影範囲(
ISO
感度(推奨露光
指数)がオートのとき)
約
1.0
m∼約
10.2 m
[入出力端子]
HDMI
端子:
HDMI
マイクロ端子
マルチ端子
*
:
USB
通信
USB
通信:
Hi-Speed USB
(
USB 2.0
)
マイク端子:
ø3.5 mm
ステレオミニジャック
ヘッドホン端子:
ø3.5 mm
ステレオミニジャック
*
この商品にはマイクロ
USB
規格に対応した機器をつ
なぐことができます。
[ファインダー]
形式:電子式ビューファインダー
総ドット数:
総ドット数:
1 440 000
ドット
視野率:
100
%
倍率:
0.70
倍(
35mm
判換算、
50 mm
レンズ、無限遠、
視度−
1 m
−1
時)
アイポイント:最終光学面から約
23 mm
、
接眼枠から約
21.5
mm(視度−
1 m
−1
時)
視度調整:−
4.0 m
−1
∼+
3.0 m
−1
(ディオプター)
[モニター]
液晶モニター:
7.5
cm
(
3.0
型)、
TFT
駆動
総ドット数:
1 228 800
ドット
[電源・その他]
電源:リチャージャブルバッテリーパック
NP-FW50
、
7.2 V
AC
アダプター
AC-UB10/UB10B/UB10C/UB10D
、
5
V
消費電力:約
2.1 W
(液晶画面で撮影時)
:約
2.7 W
(ファインダーで撮影時)
動作温度:
0
℃∼
40
℃
保存温度:−
20
℃∼
+60
℃
外形寸法(
CIPA
準拠)
(約):
129.0
mm
×
88.1 mm
×
102.2 mm
(幅×高さ×奥行き)
本体質量(
CIPA
準拠)
(約):
813
g
(バッテリー
NP-FW50
、
“メモリースティック
PRO
デュオ”を含む)
マイクロホン:ステレオ
スピーカー:モノラル
スピーカー:モノラル
Exif Print
:対応
PRINT Image Matching III
:対応
[ワイヤレスLAN]
対応規格:
IEEE 802.11b/g/n
使用周波数帯:
2.4GHz
帯
セキュリティー:
WEP/WPA-PSK/
WPA2-PSK
接続方式:
WPS
(
Wi-Fi Protected Setup
)
/
マニュアル
アクセス方式:インフラストラクチャーモード
NFC
:
NFC
フォーラム
Type 3 Tag
準拠
ACアダプター
AC-UB10/UB10B/UB10C/
UB10D
AC-UB10/UB10B/UB10C/
UB10D
定格入力:
AC 100 V
∼
240 V
、
50 Hz/60 Hz
、
70 mA
定格出力:
DC 5 V
、
0.5 A
動作温度:
0
℃∼
40
℃
保存温度:−
20
℃∼
+60
℃
外形寸法(約):
50
mm
×
22 mm
×
54 mm
(幅×高さ×奥行き)
リチャージャブルバッテリー
パックNP-FW50
パックNP-FW50
使用電池:リチウムイオン電池
最大電圧:
最大電圧:
DC 8.4 V
公称電圧:
DC 7.2 V
容量:公称容量
7.7 Wh
(
1 080 mAh
)
定格(最小)容量:
7.3 Wh
(
1 020 mAh
)
最大外形寸法(約):
31.8
mm
×
18.5 mm
×
45 mm
(幅×高さ×奥行き)
本機や付属品の仕様および外観は、改良のため予告
なく変更することがありますが、ご了承ください。
なく変更することがありますが、ご了承ください。
Model information table
Model
DSC-RX10
Destination
US, CND, E, KR, J
AEP, UK, RU, E, HK, CH
, IND
Color system
NTSC
PAL
GPS
–
–
Wi-Fi
✓
✓
NFC
✓
✓
• Abbreviation
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
IND : Indian model
J :
Japanese model
KR : Korea model
RU : Russian model
RU : Russian model
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2015.07
DSC-RX10_L2
– 3 –
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
leaded solder and leaded solder will cause detachment phenomenon.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書き及び取扱説明書等の注
意事項を必ずお守り下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図,部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用して下さい。特に回路図,部
品表に0印で指定されている安全上重要な部品は必ず指定
のものをご使用下さい。
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにして下さい。
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにして下さい。
4. サービス後は安全点検を
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認して下さい。
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認して下さい。
5. チップ部品交換時の注意
・ 取外した部品は再使用しないで下さい。
・ タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意して下さい。
6. フレキシブルプリント基板の取扱いについて
・ 半田こてのこて先温度は約350℃に設定してください。
・ 同一パターンに何度もコテ先を当てないで下さい。(3回
以内)
・ パターンに力が加わらないよう注意して下さい。
サービス,点検時には次のことにご注意ください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していてもレッ
ドフリーマークがプリントされていないものがありま
す)
す)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・ 半田こてのこて先温度は約350℃に設定してください。
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
注意: 半田こてを長く当てすぎると,基板のパターン(銅
さい。
注意: 半田こてを長く当てすぎると,基板のパターン(銅
箔)がはがれてしまうことがありますので,注意して
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
ください。また,従来の半田よりも粘性が強いため,
IC端子などが半田ブリッジしないように注意してく
ださい。
・ 半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
– ENGLISH –
– JAPANESE –
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
DSC-RX10_L2
1-1
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE SY-1027 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
RESTORE DATA
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
Start the Adjust Manual in the Adjust Station and perform “RESTORE DATA” to get the data.
The data getting for this model is as follows.
• PRODUCT ID & USB SERIAL No.
• AWB adj
• Lens Data Carry
• Light Sensor Adj
• AWB adj
• Lens Data Carry
• Light Sensor Adj
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
These IDs have not been written in a new board for service, and therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the Adjust Manual in the Adjust Station and execute the “PRODUCT ID & USB
SERIAL No. INPUT” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before board replacement. If the new ID differs from the previous ID, it may cause a difference
from the ID registered by the customer.
Update of MAC Address
When a board that contains Wi-Fi has been replaced or when replacing a board that contains the main IC (CPU), the IC’s unique number (MAC ad-
dress) must be reloaded.
Perform the following procedure to reload the IC’s unique number (MAC address).
dress) must be reloaded.
Perform the following procedure to reload the IC’s unique number (MAC address).
1. Download the latest-version Adjust Manual.
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN check” on the ADJUST tab.
4. Perform the following operations for the unit to initialize.
MENU
2. Install the downloaded Adjust Manual.
3. Start the Adjust Manual, and execute “Wireless LAN check” on the ADJUST tab.
4. Perform the following operations for the unit to initialize.
MENU
→ → [Reset Network Set.] → [OK] → ●
5. Perform the following operations for the unit to display MAC address.
MENU
MENU
→ → [Disp MAC Address] → ●
6. Confirm that the displayed MAC address has been updated.
Applicable parts
• SY-1027 BOARD, COMPLETE (SERVICE)
• WF-1002 BOARD, COMPLETE
• SY-1027 BOARD, COMPLETE (SERVICE)
• WF-1002 BOARD, COMPLETE
Note: The LOAD AND WRITE function in ADJUSTMENT DATA BACKUP on the DATA tab in the Adjust manual overwrites all data of the unit.
Therefore, the MAC address updated during the above procedure is also overwritten.
Perform the above operations after all work has been done.
After the replacement and repair, the MAC address is changed, and thus the re-setting for connection devices is required. Accordingly, download the
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
Flyer of WLAN Reset (Flyer of WLAN Reset_9834752[][].pdf) and print out it, and attach it to the set when returning the set to customer.
– ENGLISH –
Angular Velocity Sensor
When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE3100).
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity ADJ”.
Start the Adjust Manual in the Adjust Station and execute the “Angular velocity sensor sensitivity ADJ”.
Type A:
Type B:
Y P
Y P
P: PITCH sensor sensitivity
Y: YAW sensor sensitivity
SY-1027 BOARD (SIDE B)
SE3100
Note: The sensor sensitivity of SE3100 of SY-1027 board is written only repair parts.
1-2. NOTES ON REPLACING THE LENS
When replacing the lens, read the QR code given on the data sheet of the replacement lens for
service.
Start the Adjust Manual and read the QR code using a QR code reader.
The read data is used for adjustment after replacement.
Select “Lens data carry” on the ADJUST tab of the Adjust Manual, and click the LOAD button
to load the file.
service.
Start the Adjust Manual and read the QR code using a QR code reader.
The read data is used for adjustment after replacement.
Select “Lens data carry” on the ADJUST tab of the Adjust Manual, and click the LOAD button
to load the file.
QR code
DSC-RX10_L2
1-2
– ENGLISH –
1-3. NOTES ON REMOVING/INSTALLING THE IMAGER BOARD (CD-847 FLEXIBLE BOARD)
When the CD-847 Flexible Board (Imager) is mounted to the lens, shift and tilt adjustment is made with Spacer Plates.
When removing the CD-847 Flexible Board, pay attention to the following.
When removing the CD-847 Flexible Board, pay attention to the following.
(1) When the lens is not replaced
Example: In the case of disassembly, cleaning, or replacement of the CD-847 Flexible Board (Imager)
• Check and record the size of the built-in three Spacer Plates and store them so as not to lose them.
• When assembling the CD-847 Flexible Board, be sure to install the Spacer Plates to their original locations.
• When assembling the CD-847 Flexible Board, be sure to install the Spacer Plates to their original locations.
Size
0.xx
Note
Be careful not to lose the Spacer Plates.
If any Spacer Plate is lost or their previous positions are not sure, repeatedly take a photo and check that there is no local defocus.
Be careful not to lose the Spacer Plates.
If any Spacer Plate is lost or their previous positions are not sure, repeatedly take a photo and check that there is no local defocus.
Selecting appropriate Spacer Plates
is needed.
(2) When the lens is replaced
• Check the size of the built-in three Spacer Plates. If the thickness of a Spacer Plate is not
0.30
, discard the Spacer Plate.
• Prepare three Spacer Plates
C
(t =
0.30
) (Sony Part No.:
4-437-388-01
) and install them to the new lens.
0.30
1-4. CHECKING THE Wi-Fi FUNCTION
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi interface
1. Turn on the power of the unit.
2. Perform the following operations.
MENU
2. Perform the following operations.
MENU
→ → [Ctrl w/ Smartphone] → ●
3. When preparation for Wi-Fi has been completed, the following screen opens and a password for Wi-Fi connection is displayed.
Ctrl w/ Smartphone
Operate smartphone to connect to
this device via Wi-Fi.
Enter
SSID DIRECT-XXXX:DSC-XXXX
Password XXXXXXXX
Device Name DSC-XXXX
Password XXXXXXXX
Device Name DSC-XXXX
Cancel
Wi-Fi
4. Confirm on the personal computer that the unit is detected as a connectable wireless network.
5. To further confirm that the unit is connectable, connect the unit to the personal computer and select “Network and Internet” → “Manage Wireless
5. To further confirm that the unit is connectable, connect the unit to the personal computer and select “Network and Internet” → “Manage Wireless
Networks” from Control Panel to open the network connection list. The unit is included in the list.
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2014.01