Sony DSC-R1 (serv.man11) Service Manual ▷ View online
Auto-ADJ
SERVICE MANUAL
DSC-R1_ADJ
Ver 1.2 2005.11
DSC-R1
Sony EMCS Co.
9-876-898-91
2005K0500-1
© 2005.11
Published by DI Technical Support Department
CORRECTION-1
We will inform you that there are printing errors
in the service manual previously issued.
• Correction of the Before starting adjustment
• Correction of the INITIALIZATION OF DATA
• Correction of the INITIALIZATION OF DATA
— 2 —
DSC-R1_ADJ
!
: Points deleted portion.
SECTION 6
ADJUSTMENTS
Before starting adjustment
(Service Manual Page 6-1)
(The same model of the same destination)
(Machine to be repaired)
PC
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 when replacing board.
Perform either procedure 1 or procedure 2 when replacing board.
PC
Procedure 2
When the data cannot be saved due to defective flash memory, or when the flash memory cannot be removed or
installed, save the data from the same model of the same destination, and download it.
installed, save the data from the same model of the same destination, and download it.
PC
Save the EVR data
to a personal computer.
to a personal computer.
Download the saved
data to a machine.
data to a machine.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board
is replaced.
is replaced.
(Machine after a board is replaced)
(Machine before starting repair)
Download the data.
Save the data.
(Machine to be repaired)
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked.)
^
— 3 —
DSC-R1_ADJ
&
: Points added portion.
+
Precaution on Replacing the SY-132 board
• The Repair Board has already been adjusted. Re-initialization or EVR data copy from the set before repair is not
required.
• Perform “VIDEO OUT Default Data Check” mentioned below, and also the adjustment items necessary after SY Board
replacement.
1-8.
INITIALIZATION OF DATA
1.
Initializing All Page Data
(Service Manual Page 6-35)
Initializing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click
2) Click
[Sector Write]
on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is “16”.
4) Click
4) Click
[All]
of the ALL SELECT buttons to select all pages. (Fig.
6-1-90 A)
5) Click
[Write]
to write the initializing data to the flash memory
of the camera.
6) Wait for 3 sec.
7) Click
7) Click
[Close]
to close the SEUS SECTOR WRITE screen.
8) Select page: 40, address: 38 and set data: 00.
9) Select page: 2F, address: 92 and set data: 1D.
10) Select page: 2F, address: A2 and set data: 1D.
11) Select page: BC, address: 89 and set data: 03.
12) Select page: 8E, address: 00 and set data: 20.
13) Click
9) Select page: 2F, address: 92 and set data: 1D.
10) Select page: 2F, address: A2 and set data: 1D.
11) Select page: BC, address: 89 and set data: 03.
12) Select page: 8E, address: 00 and set data: 20.
13) Click
[Save]
on the SEUS screen.
14) Select page: 80, address: 34, and check that the data is “00”.
15) Select page: 80, address: 30, and check that the data is “00”.
16) Perform “VIDEO OUT Default Data Check”.
15) Select page: 80, address: 30, and check that the data is “00”.
16) Perform “VIDEO OUT Default Data Check”.
2.
Initializing Single Page Data
Initializing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Click
2) Click
[Sector Write]
on the SEUS screen to display the SEUS
SECTOR WRITE screen.
3) Check that the SET ID is “16”.
4) Click “All” of the option buttons of target page. (Fig. 6-1-90
4) Click “All” of the option buttons of target page. (Fig. 6-1-90
B
)
5) Click
[Write]
to write the initializing data to the flash memory
of the camera.
6) Wait for 3 sec.
7) Click
7) Click
[Close]
to close the SEUS SECTOR WRITE screen.
8) Select page: 40, address: 38 and set data: 00.
9) When 2F page is initialized, select page: 2F, address: 92 and set
9) When 2F page is initialized, select page: 2F, address: 92 and set
data: 1D.
10) When 2F page is initialized, select page: 2F, address: A2 and
set data: 1D.
11) When BC page is initialized, select page: BC, address: 89 and
set data: 03.
12) When 8E page is initialized, select page: 8E, address: 00 and
set data: 20.
13) Click
[Save]
on the SEUS screen.
14) Select page: 80, address: 34, and check that the data is “00”.
15) Select page: 80, address: 30, and check that the data is “00”.
16) When 4F page is initialized, perform “VIDEO OUT Default
15) Select page: 80, address: 30, and check that the data is “00”.
16) When 4F page is initialized, perform “VIDEO OUT Default
Data Check”.
*
&
Display
