DOWNLOAD Sony DSC-QX100 Service Manual ↓ Size: 7.84 MB | Pages: 41 in PDF or view online for FREE

Model
DSC-QX100
Pages
41
Size
7.84 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
dsc-qx100.pdf
Date

Sony DSC-QX100 Service Manual ▷ View online

DSC-QX100
4-15
13. Install the Naruto Gear.
14. Turn the Naruto Gear in the arrow direction to extend the Lens Barrel to the center of TELE and WIDE.
15. Pull the flexible boards out of the Lens Barrel and fix the flexible boards with the boss and the ribs.
16. Turn the Naruto Gear in the arrow direction to return the lens to the previous position.
17. Install the LF-2049 Flexible Boards.
18. Connect the two flexible boards to the connectors.
19. Install the Rear Tube Mirror Block.
20. Connect the flexible board (focus) to the connector.
Rear Tube Mirror Block
Flexible board (focus)
LF-2049 Flexible Board
Boss
Rib
Rib
Rib
Rib
Rib
Rear Tube Mirror Block
Naruto Gear
Naruto Gear
Naruto Gear
Flexible 
boards
Hook
Boss
Connectors
Flexible 
boards
Connector
DSC-QX100
4-16
24. Install the screw and the Zoom Gear Assy.
21. Stick the adhesive tape.
22. Install the Sensor.
23. Install the three screws and the Z Retainer.
Z Retainer
Zoom Gear Assy
25. Attach the LF-2049 Flexible Board to the hook.
26. Connect the LF-2050 Flexible Board to the connector.
27. Perform the Flange Back Adjustment after the assembling.
Hook
Connector
LF-2050 
Flexible Board
LF-2049 
Flexible Board
Screw
Screw
Screw
Screw
Adhesive tape
Sensor
DSC-QX100
4-17
4-4-2.   Final Inspection
(1) Confirm There Is No Fault In Actual Motion/Actual Screen
 
 
Inspect it as follows when you exchange parts in the lens block.
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
Appearance condition 
Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens 
The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Lens at WIDE end
Upward
Downward
Horizontal
Upper oblique 45
Lower oblique 45
Full stroke check
1
2
3
4
5
DSC-QX100
4-18
(2) Inspection When Cam Tube Block Assy or Straight Tube Lubricated Assy Is Replaced
Focus check
1
  Preparation
 
•  Camera installed re-assemble lens.
 
•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)
 • 
Tripod
 
•  Mirror (ex. CD)
 • 
Memory 
card
 • 
PC
2
  Shoot setting
 
(1)  Paste the chart.
 
•  Chart should be on the flat wall.
 
•  Illuminance level in the chart should be the same.
 
•  Make the tripod’s height and the center of the chart to the same height.
 
•  Enough space needed for shooting.
 
(2)  Set the camera.
 
•  Set [P] mode
 
•  Set [Maximum] size
 
•  Set ISO lowest level
 
•  Set Steady Shot [OFF]
 
•  Set Flash [OFF]
 
(3)  Set the camera on a tripod.
 
(4)  Adjust the position of the camera and the chart.
 
1. Set the zoom position of the camera at Wide end.
 
2. Attach the mirror onto the center of the chart.
 
    * The mirror should not tilt on the chart.
 
3. Set the camera to display the chart on LCD like in the following picture.
 
4. Adjust the camera position to the center of the chart.
 
    * Adjust the tripod height and the position (Lateral direction).
 
5. Adjust the camera angle to the frame of the chart with tripod.
 
    Remove the mirror.
3
  Shooting
      (1)  Set [Self-Timer]
      (2)  Shot
4
  Check the shot image.
      (1)  Check the shot image on PC.
 
100% Display (Display at the same magnification of its Pixel.)
 
Compare the image with the sample you set.
      No extreme focus blurring
      It should be distinguished the black and white by the sharpness between them.
      If it is in NG level, replace the lens unit.
<Reference>
•     How to Print the Chart
      Print “Focus-Chart_A3.pdf” with printer.
      Print at the same magnification (It means 100 % size).
      Check the settings of printer to print in proper size.
•     Check of chart size.
      Make charts together and check if the size of charts is the following size.
      * The chart consists of 2 pcs.
 
Page of 41
Display

Click on the first or last page to see other DSC-QX100 service manuals if exist.