Sony DSC-P93 (serv.man6) Service Manual ▷ View online
SERVICE MANUAL
DSC-P93_L2
LEVEL
2
Ver. 1.2 2007.09
Sony EMCS Co.
9-876-725-82
2007I0500-1
© 2007.9
Published by Kohda TEC
SUPPLEMENT-1
File this supplement with the service manual.
(DI07-161)
DSC-P93
US Model
Canadian Model
AEP Model
UK Model
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Tourist Model
• Addition of “2-5. ZOOM MOTOR UNIT REPLACEMENT
AND INSPECTION PROCEDURES”
• Addition of HELP
• Change of FP-860 Flexible Board’s Suffix No.
• Change of Repair Parts
• Revision of Accessories
• Change of FP-860 Flexible Board’s Suffix No.
• Change of Repair Parts
• Revision of Accessories
Note: Please refer to Ver.1.2 of SERVICE MANUAL (9-876-725-31) for the revision of accessories.
• Suffix No. of FP-860 flexible board has been changed from 21 into 41 , 42 .
— 2 —
DSC-P93_L2
2-5. ZOOM MOTOR UNIT REPLACEMENT AND INSPECTION PROCEDURES
Service parts
Part Number
Part Name
Quantity
1
2-891-376-01
MOTOR UINT, ZOOM
1
Note: These parts are not prepared as service parts.
Recycle removed screws.
1
Remove solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
2
Remove two screws that fix “Motor Unit, Zoom”.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
3
Confirming Zoom function manually.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
2. DISASSEMBLY
1
not supplied (Note)
Zoom Motor Unit
Two Screws
Solder
Rotate lens barrel and stroke
Length of gear
All circumferences
— 3 —
DSC-P93_L2
4
Throw in each gear of the new Motor Unit, Zoom, and fix with two screws.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
5
Solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
6
Assemble lens to the unit.
7
Execute the necessary adjustment items referring to Service Manual, ADJ.
8
Final inspection
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
Zoom Motor Unit
Two Screws
Solder
Lens stored
Lens at TELE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
— 4 —
DSC-P93_L2
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
BT Lid Assy
Insulating Sheet (330)
• Addition of HELP
Display
