DOWNLOAD Sony DSC-P9 (serv.man2) Service Manual ↓ Size: 3.08 MB | Pages: 89 in PDF or view online for FREE

5-16

The flange back of inner focus lens is adjusted automatically. If
shifted, the auto focus is disordered.

Mode

CAMERA

Subject

Siemens star chart with ND filter
for minipattern box (Note 1)

Measurement Point

Check operation on monitor TV

Measuring Instrument

Adjustment Page

F

Adjustment Address

18 to 3E, 40 to 53

Dark Siemens star chart.

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Preparations before adjustments:
1) The minipattern box is installed as shown in the following fig-

ure.

The attachment lenses are not used.

Take care not to hit the mini-pattern box when ex-
tending the lens.

2) Install the minipattern box so that the distance between it and

the front of lens of camera is less than 3 cm.

3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the

specified voltage 

±

 0.01 Vdc.

5) Check that the center of Siemens star chart meets the center of

shot image screen with the zoom lens at TELE end and WIDE
end respectively.

Specified voltage: The specified voltage varies according to the

minipattern box, so adjustment the power sup-
ply output voltage to the specified voltage writ-
ten on the sheet which is supplied with the mini-
pattern box.

Minipattern box

Below 3 cm

Camera

Camera 

table

Red (+)

Black (–)

Yellow (SENS +)

White (SENS –)

Black (GND)

Need not connected

Regulated power supply

Output voltage : Specified voltage 

±

 0.01 Vdc

Output current : more than 3.5 A

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

6

01

13

Press PAUSE button.

3

6

01

27

Press PAUSE button.
(Note 5)

4

6

02

Check the data changes to
“01”.

5

F

3E

Check the data.
00: Normal
01 to FF: Defective

The adjustment data will be automatically input to page:
F, address: 18 to 3E and 40 to 53.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1.
(Refer to page 5-14)

3

Perform “Flange Back
Check”.

5-17

The flange back of inner focus lens is adjusted automatically. If
shifted, the auto focus is disordered.

Mode

CAMERA

Subject

Flange back adjustment chart
(2.0 m from the front of lens)
(Luminance: 300 to 400 lux)

Measurement Point

 Check operation on monitor TV

Measuring Instrument

Adjustment Page

F

Adjustment Address

18 to 3E, 40 to 53

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Preparations before adjustments:
1) Place the Flange back adjustment chart 2.0 m from the front

of the lens.

2) Check that the center of Flange back adjustment chart meets

the center of shot image screen with the zoom lens at TELE
end and WIDE end respectively.

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

6

01

13

Press PAUSE button.

3

6

01

15

Press PAUSE button.
(Note 2)

4

6

02

Check the data changes to
“01”.

5

F

3E

Check the data.
00: Normal
01 to FF: Defective

The adjustment data will be automatically input to page:
F, address: 18 to 3E and 40 to 53.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1.
(Refer to page 5-14)

3

Perform “Flange Back
Adjustment (2)”.

Mode

CAMERA

Subject

Siemens star
(1.0 m from the front of the lens)
(Luminance: 200 to 400 lux)

Measurement Point

Check operation on monitor TV

Measuring Instrument

Specified value

Focused at the TELE end and
WIDE end

Order Page Address Data

Procedure

1

Place the Siemens star 1.0 m
from the front of the lens.

2

To open the IRIS , decrease
the luminous intensity to the
Siemens star up to a point
before noise appear on the
image.

3

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

4

B

3D

Note down the data.

5

B

3D

50

Press PAUSE button.

6

Shoot the Siemens star with
the zoom TELE end.

7

Turn on the auto focus.

8

Check that the lens is
focused.

9

6

2C

01

10

While observe the TV
monitor, change the zoom to
the WIDE end and check that
the lens is focused.

Order Page Address Data

Procedure

1

6

2C

00

2

B

3D

Set data noted down at step
4, and press PAUSE button.

3

Release the data setting
performed at step 3.
(Refer to page 5-14)

5-18

Compensate the unevenness of the iris meter sensitivity.

Mode

CAMERA

Subject

Clear chart
(Standard picture frame with the
zoom lens at WIDE end)

Adjustment Page

F

Adjustment Address

5E to 64

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

Perform “Picture Frame
setting”.
(Refer to page 5-15)

3

6

01

BB

Press PAUSE button.
(Note 2)

4

6

02

Check the data changes to
“01”.

The adjustment data will be automatically input to page:
F, address: 5E to 64.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1.
(Refer to page 5-14)

Adjust the period which the mechanical shutter is closed, and com-
pensate the exposure.

Mode

CAMERA

Subject

Clear chart
(Standard picture frame with the
zoom lens at WIDE end)

Adjustment Page

F

Adjustment Address

B8 to D7

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

Perform “Picture Frame
setting”.
(Refer to page 5-15)

3

6

01

AD

Press PAUSE button.
(Note 2)

4

6

02

Check the data changes to
“01”.

5

6

AB

Check the data is “00”.

The adjustment data will be automatically input to page:
F, address: B8 to D7.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

Release the data setting
performed at step 1.
(Refer to page 5-14)

5-19

Adjust the standard LV value.

Mode

CAMERA

Subject

Clear chart
(Standard picture frame with the
zoom lens at WIDE end)

Measurement Point

Displayed data of page: 1 (Note
2) and page: F, address: 65

Measuring Instrument

Adjusting remote commander

Adjustment Page

F

Adjustment Address

65 to 67

Specified Value

AE level 1: 0FE0 to 1020
AE level 2: 2F to 50

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

The right four digits of the page: 1 displayed data of the
adjusting remote commander.

1:XX:XX

Displayed data

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

Perform “Picture Frame
setting”.
(Refer to page 5-15)

3

6

01

0D

Press PAUSE button.
(Note 4)

4

6

02

Check the data changes to
“01”.

5

0

03

06

6

1

Check that the displayed data
(Note 2) satisfies the AE
level 1 specified value.

7

F

65

Check that the displayed data
satisfies the AE level 2
specified value.

The adjustment data will be automatically input to page:
F, address: 65 to 67.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

0

03

00

3

Release the data setting
performed at step 1.
(Refer to page 5-14)

To perform mixed color cancel adjustment based on data of each
color in color bar.

Mode

CAMERA

Subject

Color bar chart
(Standard picture frame with the
zoom lens at WIDE end)

Adjustment Page

F

Adjustment Address

6E and 6F

Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.

Order Page Address Data

Procedure

1

Perform “Data setting during
camera system adjustment”.
(Refer to page 5-14)

2

Perform “Picture Frame
setting”.
(Refer to page 5-15)

3

7

22

Note down the data.

4

7

22

00

Press PAUSE button.

5

6

01

D7

Press PAUSE button.

6

6

01

D5

Press PAUSE button.
(Note 2)

7

6

02

Check the data changes to
“01”.

The adjustment data will be automatically input to page:
F, address: 6E and 6F.

Order Page Address Data

Procedure

1

6

01

00

Press PAUSE button.

2

7

22

Set the data noted down at
step 3, and press PAUSE
button.

3

Release the data setting
performed at step 1.
(Refer to page 5-14)