DOWNLOAD Sony DSC-P73 (serv.man2) Service Manual ↓ Size: 3.76 MB | Pages: 47 in PDF or view online for FREE

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987673352.pdf).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987673343.pdf).

• Reference No. search on printed wiring boards is available.

• Note in Lens Frame Installation
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

This service manual procides the information that is premised
the circuit board replacement service and not intended repair
inside the CH-146 and SY-100 boards.
Therefore, schematic diagram, printed wiring board and
electrical parts list of the CH-146 and SY-100 boards are not
shown.
The following pages are not shown.

Schematic diagram ............ Pages 4-9 to 4-26
Printed wiring board ........... Pages 4-39 to 4-42
Mounted parts location ....... Pages 4-50
Electrical parts list .............. Pages 5-7 and 5-10 to 5-13

The above-described information is shown in service
manual Level 3.

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

Japanese Model

Photo: Silver

— 2 —

White balance

Automatic, Daylight, Cloudy, 
Fluorescent, Incandescent

File format (DCF compliant)

Still images: Exif Ver. 2.2, JPEG 
compliant, DPOF compatible
Movies: MPEG1 compliant 
(Monaural)

Recording medium

“Memory Stick”

Flash

Recommended distance (when ISO 
sensitivity is set to Auto)
0.2 to 3.5 m (7

7

/

8

inches to 

11 feet 5

7

/

8

inches) (W)

0.5 to 3.5 m (19

3

/

4

inches to 

11 feet 5

7

/

8

inches) (T)

A/V OUT (MONO) jack (Monaural)

Minijack
Video: 1 Vp-p, 75 

Ω, unbalanced, 

sync negative
Audio: 327 mV (at a 47 k

Ω load)

Output impedance 2.2 k

Ω

USB jack

mini-B

USB communication

Hi-Speed USB (USB 2.0 compliant)

LCD panel used

3.8 cm (1.5 type) TFT drive

Total number of dots

67 200 (280

×240) dots

Power 

AA nickel hydride batteries (2)
2.4 V
AC-LS5 AC Adaptor
(not supplied), 4.2 V

Power consumption (during shooting with LCD 

screen on)
1.1 W

Operating temperature range

0

° to +40°C (32° to +104°F)

Storage temperature range

−20° to +60°C (−4° to +140°F)

Dimensions

117.2 

× 53.7 × 35.8 mm 

(4 

5

/

8

 

× 2 

1

/

8

 

× 1 

7

/

16

inches)

(W/H/D, protruding portions not 
included)

Mass

Approx. 236 g (0.5 lb 8.3 oz) (two 
batteries, “Memory Stick,” wrist 
strap, and so on included)

Microphone

Electret condenser microphone

Speaker

Dynamic speaker

Exif Print

Compatible

PRINT Image Matching II

Compatible

PictBridge

Compatible

x

Power requirements

AC 100 to 240V 50/60Hz
3 W

Output voltage

AA : DC 1.4 V  400 mA 

× 2

AAA : DC 1.4 V  160 mA 

× 2

Operating temperature range

0

° to +40°C (32° to +104°F)

Storage temperature range

−20° to +60°C (−4° to +140°F)

Dimensions

71 

× 30 × 91 mm 

(2 

7

/

8

 

× 1 

3

/

16

 

× 3 

5

/

8

 inches) (W/H/

D)

Mass

Approx. 90 g (3 oz)

x

Input rating

AC 100 to 240 V, 50/60 Hz 
11 W, 0.16 to 0.09 A

Output rating DC 4.2 V, 1.5 A

Operating temperature range

0

° to +40°C (32° to +104°F)

Storage temperature range

−20° to +60°C (−4° to +140°F)

Maximum dimensions

Approx. 48 

× 29 × 81 mm (1 

15

/

16

 

× 

1 

3

/

16

 

× 3 

1

/

4

 inches) (W/H/D)

Mass

Approx. 130 g (5 oz)

x

Image device 6.85 mm (1/2.7 type) color

CCD
Primary color filter

Total pixels number of camera

Approx. 4 231 000 pixels

Effective pixels number of camera

Approx. 4 065 000 pixels

Lens

3

× zoom lens

f=6 to 18 mm
(35 mm camera conversion: 39 to 
117 mm)
F2.8-5.2

Exposure control

Automatic, Manual exposure, 
Twilight, Twilight portrait, Candle, 
Landscape, Beach, Soft snap

• HR6 (size AA) Ni-MH batteries (2)
• Battery case (1)
• BC-CS2A/CS2B Ni-MH Battery charger (1)
• Power cord (mains lead) (1)
• USB cable (1)
• A/V connecting cable (1)
• Wrist strap (1)
• “Memory Stick” (16MB) (1)
• CD-ROM (USB driver: SPVD-012) (1)
• Operating Instructions (1)
See page 5-14.

Design and specifications are subject to change 
without notice.

— 3 —

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

0

0

0

— 4 —

1-1.

Note for Repair ································································ 1-1

1-2.

Discharging of the ST-097 Board’s Charging Capacitor
(C852) ·············································································· 1-1

1-3.

Note in Lens Frame Installation ······································ 1-2

1-4.

Description on Self-diagnosis Display ···························· 1-2

2-1.

Flow Chart ······································································· 2-1

2-2.

SY-100 Board Service Position ······································· 2-3

2-3.

Circuit Boards Location ·················································· 2-5

2-4.

Flexible Boards Location ················································ 2-5

3-1.

Overall Block Diagram (1/2) ··········································· 3-1

3-2.

Overall Block Diagram (2/2) ··········································· 3-3

3-3.

Power Block Diagram (1/2) ············································· 3-5

3-4.

Power Block Diagram (2/2) ············································· 3-7

4-1.

Frame Schematic Diagram ·············································· 4-1

4-2.

Schematic Diagrams ························································ 4-5

CD-500 (CCD IMAGER) ··············································· 4-7
SW-419 (CONTROL SWITCH, LCD DRIVE) ··········· 4-27
ST-097 (FLASH DRIVE) ············································· 4-29
MS (FP-861 FLEXIBLE)
(MEMORY STICK CONNECTOR) ···························· 4-31
FP-860 FLEXIBLE (JACK) ········································· 4-32
MIC UNIT (MA-002) ··················································· 4-33
CONTROL SWITCH BLOCK (RL530TT) ················· 4-34

4-3.

Printed Wiring Boards ··················································· 4-35
CD-500 ·········································································· 4-37
SW-419 ·········································································· 4-43
ST-097 ··········································································· 4-45
MS (FP-861 FLEXIBLE) ·············································· 4-47
FP-860 FLEXIBLE ······················································· 4-48

4-4.

Mounted Parts Location ················································ 4-49

5-1.

Exploded Views ······························································· 5-2

5-1-1. Front Cabinet Block Section ··········································· 5-2
5-1-2. Lens Block Section ·························································· 5-3
5-1-3. BT Holder Block Section ················································ 5-4
5-1-4. Rear Cabinet Block Section ············································ 5-5
5-2.

Electrical Parts List ························································· 5-6

Section

Title

Page