DOWNLOAD Sony DSC-P200 (serv.man2) Service Manual ↓ Size: 5.48 MB | Pages: 40 in PDF or view online for FREE

DSC-P200

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-854-51).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-854-41).

• Reference No. search on printed wiring boards is available.

• Note in Lens Frame Installation
• Exchange Method of Barrier Assy

2006G0500-1

  © 2006.7

US Model

Canadian Model

AEP Model

UK Model

E Model

Hong Kong Model

Australian Model

Chinese Model

Korea Model

Argentine Model

Brazilian Model

Tourist Model

Japanese Model

Photo: Silver

This service manual procides the information that is premised the
circuit board replacement service and not intended repair inside the
CH-146, SY-123 boards.
Therefore, schematic diagram, printed wiring board and electrical
parts list of the CH-146, SY-123 boards are not shown.
The following pages are not shown.

Schematic diagrams .................. Pages 4-9 to 4-28
Printed wiring boards ................ Pages 4-39 to 4-42
Waveforms ................................ Pages 4-45 and 4-46
Mounted parts location .............. Page 4-48 and 49
Electrical parts list ..................... Pages 5-7 to 5-11

The above-described information is shown in service manual Level 3.

— 2 —

DSC-P200

Image device

9.11 mm (1/1.8 type) color 
CCD, Primary color filter

Total pixel number of camera

Approx. 7 410 000 pixels

Effective pixel number of camera

Approx. 7 201 000 pixels

Lens

Carl Zeiss Vario-Tessar
3× zoom lens
f = 7.9 - 23.7 mm (38 - 114 mm 
when converted to a 35 mm still 
camera)
F2.8 - 5.2

Exposure control Automatic exposure, Manual 

exposure, Scene Selection (9 
modes)

White balance

Automatic, Daylight, Cloudy, 
Fluorescent, Incandescent, 
Flash, One push

File format (DCF compliant)

Still images: Exif Ver. 2.2
JPEG compliant, DPOF 
compatible
Movies: MPEG1 compliant 
(Monaural)

Recording media “Memory Stick”

Flash

Recommended distance (ISO 
set to Auto): 0.2 m to 3.5 m 
(7 7/8 inches to 11 feet 5 3/4 
inches) (W)/0.3 m to 2.5 m 
(11 7/8 inches to 8 feet 2 3/8 
inches) (T)

Multi connector 

USB communication

Hi-Speed USB (USB 2.0 
compliant)

LCD panel

5.1 cm (2.0 type) TFT drive

Total number of dots

134 000 (560×240) dots

Battery pack used

NP-FR1

Power requirements

3.6 V

Power consumption
(during shooting with the LCD screen on)

1.2 W

Operating temperature

0°C to +40°C (+32°F to 
+104°F)

Storage temperature

–20°C to +60°C (–4°F to 
+140°F)

Dimensions

104.5×51.5×27.9 mm
(4 1/8×2 1/8×1 1/8 inches)
(W/H/D, excluding maximum 
protrusions)

Mass

Approx. 180 g (6.3 oz) 
(including NP-FR1 battery 
pack, “Memory Stick”, and 
wrist strap)

Microphone

Electret condenser microphone

Speaker

Dynamic speaker

Exif Print

Compatible

PRINT Image Matching II

Compatible

PictBridge

Compatible

Input rating

100 V to 240 V AC, 50/60 Hz, 
11 W

Output rating

4.2 V DC*
* See the label on the AC 
Adaptor for other 
specifications.

Operating temperature

0°C to +40°C (+32°F to 
+104°F)

Storage temperature

–20°C to +60°C (–4°F to 
+140°F)

Dimensions

Approx. 48×29×81 mm
(1 15/16×1 3/16×3 1/4 inches) 
(W/H/D, excluding projecting 
parts)

Mass

Approx. 130 g (5 oz) excluding 
power cord (mains lead)

Battery used

Lithium-ion battery

Maximum voltage

DC 4.2 V

Nominal voltage DC 3.6 V

Capacity

4.4 Wh (1 220 mAh)

Design and specifications are subject to change 
without notice.

— 3 —

DSC-P200

0

0

0

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°

C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

— 4 —

DSC-P200

1-1.

Note for Repair ································································ 1-1

1-2.

Discharging of the FP-163 Flexible Board’s Charging
Capacitor (C601) ····························································· 1-1

1-3.

Note in Lens Frame Installation ······································ 1-2

1-4.

Description on Self-diagnosis Display ···························· 1-2

2-1.

Disassembly ····································································· 2-1

2-2.

SY-123 Board Service Position ······································· 2-5

2-3.

Exchange Method of Barrier Assy ·································· 2-7

2-3-1. Peel Off Old Ornamental Ring A ···································· 2-7
2-3-2. Remove Old Barrier Assy ················································ 2-8
2-3-3. Install New Barrier Assy ················································· 2-8
2-3-4. Adhere the Ornamental Ring A ······································· 2-9
2-4.

Circuit Boards Location ················································ 2-10

3-1.

Overall Block Diagram (1/2) ··········································· 3-1

3-2.

Overall Block Diagram (2/2) ··········································· 3-3

3-3.

Power Block Diagram (1/2) ············································· 3-5

3-4.

Power Block Diagram (2/2) ············································· 3-7

4-1.

Frame Schematic Diagram ·············································· 4-1

4-2.

Schematic Diagrams ························································ 4-5
CD-517 FLEXIBLE (CCD IMAGER) ···························· 4-7
FP-162 FLEXIBLE
(DC IN, MULTI CONNECTOR) ·································· 4-29
FP-163 FLEXIBLE (FLASH) ······································· 4-30
MEMORY STICK CONNECTOR
(FP-161 FLEXIBLE) ····················································· 4-30
CONTROL SWITCH BLOCK (SW51740), (RL) ········ 4-31

4-3.

Printed Wiring Boards ··················································· 4-35
CD-517 FLEXIBLE ······················································ 4-37
FP-162 FLEXIBLE ······················································· 4-43
FP-163 FLEXIBLE ······················································· 4-44

4-5.

Mounted Parts Location ················································ 4-47

5-1.

Exploded Views ······························································· 5-2

5-1-1. Overall Assembly ···························································· 5-2
5-1-2. Lens Block Assembly ······················································ 5-3
5-1-3. Main Block Assembly ····················································· 5-4
5-1-4. BT Block Assembly ························································· 5-5
5-2.

Electrical Parts List ························································· 5-6

Section

Title

Page