Sony DSC-P2 (serv.man2) Service Manual ▷ View online
— 5 —
DSC-P2
6-1-3. Lens Block and LCD Section ·········································· 6-3
6-1-4. Battery Holder Assembly ················································ 6-4
6-2.
6-1-4. Battery Holder Assembly ················································ 6-4
6-2.
Electrical Parts List ························································· 6-5
Section
Title
Page
*
The color reproduction frame is shown on page 117.
1-1
SECTION 1
SERVICE NOTE
DSC-P2
COVER
COVER
[Discharging of the ST-70 flexible board’s charging
capacitor (C510)]
capacitor (C510)]
The charging capacitor (C003) of the ST-70 flexible board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
battery is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω
/1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
•
NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Capacitor
1-2
DSC-P2
[Precaution on Replacing the Video Lens or the SY-77
Board]
Board]
The DSC-P2 uses the position sensor to detect the zoom position.
Accordingly, the zoom position will vary if the position data changes
due to the replacement of the video lens or the SY-77 board, thus
causing the video lens to collide against the mechanism end when
the power is turned off.
Though the position data is calibrated at the “Flange Back
Adjustment”, add the following work when making an adjustment
at the replacement of video lens to prevent a collision of video lens.
Accordingly, the zoom position will vary if the position data changes
due to the replacement of the video lens or the SY-77 board, thus
causing the video lens to collide against the mechanism end when
the power is turned off.
Though the position data is calibrated at the “Flange Back
Adjustment”, add the following work when making an adjustment
at the replacement of video lens to prevent a collision of video lens.
When Replacing the Video Lens
1) With current video lens assembled, turn the power on, and set
1) With current video lens assembled, turn the power on, and set
the bit value of Bit0 on Page:9, Address:17 to “0” using the
adjusting remote commander, then turn the power off.
adjusting remote commander, then turn the power off.
2) Replace the video lens with a new one, turn the power on, and
perform the “Flange Back Adjustment”.
Thus, new position data will be written.
Thus, new position data will be written.
3) After the “Flange Back Adjustment”, return the bit value of Bit0
on Page:9, Address:17 to “1” using the adjusting remote
commander.
commander.
When Replacing the SY-77 Board
1) Replace the SY-77 board with a new one, set the mode dial to
1) Replace the SY-77 board with a new one, set the mode dial to
“PLAY”, turn the power on, and set the bit value of Bit0 on
Page:9, Address:17 to “0” using the adjusting remote
commander, then turn the power off.
Page:9, Address:17 to “0” using the adjusting remote
commander, then turn the power off.
2) Set the mode dial to “CAMERA”, turn the power on, and
perform the “Flange Back Adjustment”.
Thus, new position data will be written.
Thus, new position data will be written.
3) After the “Flange Back Adjustment”, return the bit value of Bit0
on Page:9, Address:17 to “1” using the adjusting remote
commander.
commander.
[Note in Lens Frame Installation]
When tightening a screw, have both sides of the lens block assembly
so as not for the load to depend.
so as not for the load to depend.
M1.7
×
4
M1.7
×
4
Lens frame
Lens block assembly
1-3E
DSC-P2
[Description on Self-diagnosis Display]
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
Display Code
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
Abnormality when flash is being
charged.
charged.
Click on the first or last page to see other DSC-P2 (serv.man2) service manuals if exist.