DOWNLOAD Sony DSC-P150 (serv.man12) Service Manual ↓ Size: 5.53 MB | Pages: 52 in PDF or view online for FREE

DSC-P150

• Para os AJUSTES (SEÇÃO 6), consulte MANUAL DE SERVIÇO DO AJUSTE (9

8901645

1.pdf).

• Note in Lens Frame Installation
• Exchange Method of Barrier Assy
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.

This service manual procides the information that is premised
the circuit board replacement service and not intended repair
inside the CH-146 and SY-119 boards.
Therefore, schematic diagram, printed wiring board and
electrical parts list of the CH-146 and SY-119 boards are not
shown.
The following pages are not shown.

Schematic diagram ............ Pages 4-9 to 4-28
Printed wiring board ........... Pages 4-39 to 4-42
Mounted parts location ....... Pages 4-50 and 4-51
Electrical parts list .............. Pages 5-6 and 5-8 to 5-12

The above-described information is shown in service
manual Level 3.

Photo: Silver

Brazilian Model

2004H0500-1

  ©2004.8

— 2 —

DSC-P150

Hi-Speed USB (USB 2.0 compliant)

4.6 cm (1.8 type) TFT drive

134 000 (560

×240) dots

NP-FR1

3.6 V

1.4W

0

°C to +40°C (+32°F to +104°F)

−20°C to +60°C (−4°F to +140°F)

108

×51.5×26.6 mm 

(4 3/8

×2 1/8×1 1/16 inches)

(W/H/D, excluding maximum 
protrusions)

Approx. 183 g (6.5 oz) (including 
battery pack NP-FR1, “Memory 
Stick” and wrist strap)

Electret condenser microphone

Dynamic speaker

Compatible

Compatible

Compatible

x

100 V to 240 V AC, 50/60 Hz, 11 W, 
0.16 A to 0.09 A

4.2 V DC, 1.5 A

0

°C to +40°C (+32°F to +104°F) 

−20°C to +60°C (−4°F to +140°F) 

Approx. 48

×29×81mm 

(1 15/16

×1 3/16×3 1/4 inches) 

(W/H/D, excluding projecting parts)

Approx. 130 g (5 oz) excluding 
power cord (mains lead)

x

Lithium-ion battery 

DC 4.2 V 

DC 3.6 V

4.4 Wh (1220 mAh)

x

• AC-LS5/LS5B AC Adaptor (1) 
• Power cord (mains lead) (1)
• NP-FR1 battery pack (1)
• Battery case (1)
• USB, A/V cable for multi-use terminal (1)
• Wrist strap (1)
• “Memory Stick” (32 MB) (1)
• CD-ROM (USB driver SPVD-012) (1)
• Operating instructions (1)
See page 5-13.

Design and specifications are subject to change 
without notice.

x

9.11 mm (1/1.8 type) color CCD
Primary color filter

Approx. 7 410 000 pixels

Approx. 7 201 000 pixels

Carl Zeiss Vario-Tessar
3

× zoom lens

f = 7.9 

− 23.7 mm (38 − 114 mm when 

converted to a 35 mm still camera)
F2.8 

− 5.2

Automatic exposure, Manual 
exposure, Scene selection (9 modes)

Automatic, Daylight, Cloudy, 
Fluorescent, Incandescent, Flash

Still images: Exif Ver. 2.2 JPEG 
compliant, DPOF compatible
Movies: MPEG1 compliant 
(Monaural)

“Memory Stick”

Recommended distance (ISO set to 
Auto): 
0.2 m to 3.5 m (7 7/8 inches to 11 feet 
5 3/4 inches) (W)
0.3 m to 2.5 m (11 7/8 inches to 8 feet 
2 3/8 inches) (T)

— 3 —

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

DSC-P150

0

0

0

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

— 4 —

DSC-P150

1-1.

Note for Repair ································································ 1-1

1-2.

Discharging of the ST-105 Flexible Board’s Charging
Capacitor (C550) ····························································· 1-1

1-3.

Note in Lens Frame Installation ······································ 1-2

1-4.

Description on Self-diagnosis Display ···························· 1-2

2-1.

Flow Chart ······································································· 2-1

2-2.

SY-119 Board Service Position ······································· 2-3

2-3.

Exchange Method of Barrier Assy ·································· 2-5

2-3-1. Peel Off Old Ornamental Ring A ···································· 2-5
2-3-2. Remove Old Barrier Assy ················································ 2-6
2-3-3. Install New Barrier Assy ················································· 2-6
2-3-4. Adhere the Ornamental Ring A ······································· 2-7
2-4.

Circuit Boards Location ·················································· 2-8

3-1.

Overall Block Diagram (1/2) ··········································· 3-1

3-2.

Overall Block Diagram (2/2) ··········································· 3-3

3-3.

Power Block Diagram (1/2) ············································· 3-5

3-4.

Power Block Diagram (2/2) ············································· 3-7

4-1.

Frame Schematic Diagram ·············································· 4-1

4-2.

Schematic Diagrams ························································ 4-5

CD-517 FLEXIBLE (CCD IMAGER) ··························· 4-7
ST-105 FLEXIBLE (CHARGING CAPACITOR) ······· 4-29
ST-102 (FLASH DRIVE) ············································· 4-29
MS-207 FLEXIBLE
(MEMORY STICK CONNECTOR) ···························· 4-31
JK-266 FLEXIBLE
(DC IN, MULTI CONNECTOR) ································· 4-32
CONTROL SWITCH BLOCK (SW), (RL51600) ······· 4-33

4-3.

Printed Wiring Boards ··················································· 4-35
CD-517 FLEXIBLE ······················································ 4-37
ST-105 FLEXIBLE ······················································· 4-43
ST-102 ··········································································· 4-44
MS-207 FLEXIBLE ······················································ 4-45
JK-266 FLEXIBLE ······················································· 4-46

4-4.

Mounted Parts Location ················································ 4-49

5-1.

Exploded Views ······························································· 5-2

5-1-1. Cabinet Block Section ····················································· 5-2
5-1-2. Lens Block Section ·························································· 5-3
5-1-3. BT Holder Block Section ················································ 5-4
5-2.

Electrical Parts List ························································· 5-5

Section

Title

Page