Sony DSC-P10 / DSC-P12 (serv.man12) Service Manual ▷ View online
SERVICE MANUAL
LEVEL
2
Ver. 1.8 2007.11
Sony EMCS Co.
9-876-227-88
2007K0500-1
© 2007.11
Published by Kohda TEC
SUPPLEMENT-5
File this supplement with the service manual.
(DI07-216)
• Addition of “2-15. ZOOM MOTOR UNIT REPLACEMENT
AND INSPECTION PROCEDURES”
DSC-P10/P12_L2
DSC-P10/P12
US Model
Canadian Model
DSC-P10
AEP Model
UK Model
DSC-P10/P12
E Model
Hong Kong Model
Australian Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
DSC-P10
— 2 —
DSC-P10/P12_L2
SECTION 2
DISASSEMBLY
2-15.ZOOM MOTOR UNIT REPLACEMENT AND INSPECTION PROCEDURES
Service parts
Part Number
Part Name
Quantity
1
2-891-376-01
MOTOR UINT, ZOOM
1
Note: These parts are not prepared as service parts.
Recycle removed screws.
1
Remove solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
2
Remove two screws that fix “Motor Unit, Zoom”.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Removed screws are recycled. Do not lose them.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
3
Confirming Zoom function manually.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
3-1. Turn Lens gear to clockwise and poke put the lens barrel until the position of open lens barrier.
3-2. Turn to the lens barrel (outside) for TELE end and WIDE end for four or five times and then confirm no against force during stroke.
3-3. During the lens barrel stroke check, confirm the condition of lens gear if there is no deformation of damage.
3-4. If everything is OK, step forward to next.
* If found any problem until this point, it is impossible to repair ZOOM motor unit. Therefore, replace the lens block assembly.
1
not supplied (Note)
Zoom Motor Unit
Two Screws
Solder
Rotate lens barrel and stroke
Length of gear
All circumferences
— 3 —
DSC-P10/P12_L2
4
Throw in each gear of the new Motor Unit, Zoom, and fix with two screws.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
* Lens barrel should not be pulled out.
* Do not touch the motor directly for preventing rust. (Use finger cot etc...)
* Be careful not to damage the appearance.
5
Solder of “Zoom motor terminal” (4 point).
* Be careful for terminal deformation and breaking of coil.
* Be careful for terminal deformation and breaking of coil.
6
Assemble lens to the unit.
7
Execute the necessary adjustment items referring to Service Manual, ADJ.
8
Final inspection
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
8-1. Zoom function
* Confirm five position. (refer to the picture)
* Make sure if there is no mechanical noise and illegal motion when zooming (From TELE end to WIDE end).
8-2. Zooming picture
* Make sure if there is no missing frame or unstable pictures in LCD or EVF.
8-3. Barrier
* Confirm five position. (refer to the picture)
* Make sure if it moves smoothly without any interference, and does not have abnormal sound.
8-4. Appearance
* Make sure if there is no scratch or dirt on the surface unless customers permit.
8-5. Dust on lens
* Make sure if there is no dust in the lens.
Zoom Motor Unit
Two Screws
Solder
Lens stored
Lens at TELE end
Upward
Downward
Horizontal
Upper oblique 45˚
Lower oblique 45˚
Full stroke check
— 4 —
DSC-P10/P12_L2
67
2-891-376-01 MOTOR UNIT, ZOOM
Page
Former
New
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
5-3
ns: not supplied
(Note 2) Be sure to read “2-15. ZOOM MOTOR
UNIT REPLACEMENT AND INSPEC-
TION PROCEDURES” on page 2 when
change Ref. No. 67.
TION PROCEDURES” on page 2 when
change Ref. No. 67.
&
: Points added portion.
: Points changed portion.
: Points changed portion.
SECTION 5
REPAIR PARTS LIST
5-1. EXPLODED VIEWS
51
ns
ns
51
67
(Note 2)
ns
+
&
Display
