Sony DSC-N2 (serv.man2) Service Manual ▷ View online
1-3
DSC-N2_L2
Method for Formatting the Music
If you cannot play back a Music file for the Slide Show, the Music file might be corrupted. If
this happens, perform [Format Music], then transfer the music by [Download Music] using the
supplied “Music Transfer” software.
this happens, perform [Format Music], then transfer the music by [Download Music] using the
supplied “Music Transfer” software.
• If you format the write-in-area of the Music file, all Music files are deleted and cannot be restored.
The message “All data will be erased Ready?” appears.
Format Music
OK
Formats the Music files. All data other than Music files remain as
it is.
it is.
Cancel
Cancels the formatting.
1-4E
DSC-N2_L2
1-4. PRECAUTION ON REPLACING THE SY-165 BOARD
VIDEO OUT Default Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast
system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite
to the right value.
system (NTSC/PAL).
When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite
to the right value.
VIDEO OUT Default Data
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 89, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 89, and set data: 00 (NTSC) or data: 01 (PAL).
3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL).
4) Select page: 40, address: 38, and set data: 00.
5) Click
[Save]
on the SEUS screen.
6) Select page: 80, address: 34, and check that the data is “00”.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
7) Select page: 80, address: 30, and check that the data is “00”.
8) Select page: 00, address: 01, and set data: 00.
Initial Language Data Check
If the SY-165 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial
language as that of the set distributing in each region.
language as that of the set distributing in each region.
Initial language: Language displayed at the next starting if the setting of Setup menu was reset.
It is different from the language setting selectable with the menu.
Initial Language Data
Page
Address
Data
Language
GP1
GP2
GP3
GP4
4F
88
00
English
z
z
z
01
Japanese
z
04
Spanish
z
z
08
Simplified Chinese
z
0B
Russian
z
0D
Korean
z
Note: GP1 is fixed to Japanese.
GP2 is fixed to English.
GP3 is either English, Spanish or Russian.
GP4 is either English, Spanish, Simplified Chinese or Korean.
GP3 is either English, Spanish or Russian.
GP4 is either English, Spanish, Simplified Chinese or Korean.
Writing Method:
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 88, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
1) Select page: 00, address: 01 and set data: 01.
2) Select page: 4F, address: 88, and set the Initial Language Data.
3) Select page: 40, address: 38, and set data: 00.
4) Click
[Save]
on the SEUS screen.
5) Select page: 80, address: 34, and check that the data is “00”.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
6) Select page: 80, address: 30, and check that the data is “00”.
7) Select page: 00, address: 01, and set data: 00.
8) Turn off the camera.
9) Turn on the camera. Execute “Initialize” of Setup screen.
10) Check the language displayed when the camera starts.
Address
00
01
89
4F
Page
Data
NTSC
PAL
00
01
A2
4F
2-1
2. DISSASSEMBLY
DSC-N2_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE ST-129 FLEXIBLE BOARD’S CHARGING CAPACITOR (C901)
The charging capacitor (C901) of the ST-129 FLEXIBLE board
is charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
is charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
Short-circuit between the two points
with the short jig about 10 seconds.
R:1 k
Ω/1 W
(Part code: 1-215-869-11)
DSC-N2_L2
2-2
HARDWARE LIST
HARDWARE LIST
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
2
2
2
1
Flexible board
x1
2
Claw
x3
3
Microphone holder
4
#45
x1
5
#46
x4
6
Cabinet (rear) block
1
Insert the flat blade
screw driver.
screw driver.
2
Claw
x1
3
Claw
x2
4
Multi cap
5
Flexible board
x2
6
#46
x1
7
Remove the SY-MC board.
8
Flexible board
x2
9
SY-MC board.
1
#45
x5
2
Claw
x2
3
Cabinet (front) block
4
Flexible board
x2
5
Flexible board
x1
6
Lens block
6
5
4
4
Refer to page 2-1
" Discharging of the ST-129 flexible board's
charging capacitor (C901) ",
when discharging the capacitor.
" Discharging of the ST-129 flexible board's
charging capacitor (C901) ",
when discharging the capacitor.
1
Claw
x1
2
Claw
x2
3
Remove the ST board.
4
Claw
x3
5
Holder (AF)
6
Discharging the Capacitor.
1
Rotate the ornamental ring (A),
and release the bond.
and release the bond.
2
Ornamental ring (A)
3
Insert the tweezers etc..
4
Claw
x3
5
Barrier block assembly
1
2
3
4
4
5
6
7
1
2
3
4
5
6
3
1
1
2
3
4
6
7
5
8
5
9
1
2
8
3
1
2
4
4
5
1
7
Claw
x1
8
ST board
Note: When you exchange
barrier block assembly
and ornamental ring (A), be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assembly" (2-4 page).
and ornamental ring (A), be sure
to follow the procedure carried on
"2-3. Exchange Method of Barrier
Assembly" (2-4 page).
Position of claws
(#45)
(#46)
HELP
(#45)
(#45)
(#45)
(#46)
2
HELP
HELP
Click on the first or last page to see other DSC-N2 (serv.man2) service manuals if exist.