Sony DSC-N2 (serv.man2) Service Manual ▷ View online
DSC-N2_L2
2-3
2-2. THE METHOD OF ATTACHMENT OF CABINET CENTER BLOCK
Lock claw (BT)
MS guide light
BT cover
BT cover
Spring (lock claw)
Cabinet (center) block
boss
hook
1
2
3
4
1
Spring (lock claw)
x1
2
Lock claw (BT)
x1
3
BT cover
x1
Slide until the hook of the BT cover
reaches the boss of the cabinet.
reaches the boss of the cabinet.
4
MS guide light
x1
5
Slide the BT cover at the bottom.
Check it the BT cover is locked and not removed.
Check it the BT cover is locked and not removed.
5
2-4
DSC-N2_L2
2-3. EXCHANGE METHOD OF BARRIER ASSEMBLY
2-3-1. PEEL OFF OLD ORNAMENTAL RING (A)
Turn on the power, and set the zoom to the TELE end. Remove the battery forcibly.
Turn the ornamental ring (A) clockwise to remove.
* Discard the removed ornamental ring (A).
Turn the ornamental ring (A) clockwise to remove.
* Discard the removed ornamental ring (A).
Ornamental ring (A)
2-3-2. REMOVE OLD BARRIER BLOCK ASSEMBLY
Inert tweezers, etc. into a slit in the lens, and pry the barrier block assembly with the fulcrum at a hole in the 1 group frame.
* Discard the removed barrier block assembly.
* Discard the removed barrier block assembly.
Slit
1 group frame
Claw
Claw
Barrier block
assembly
assembly
2-5
DSC-N2_L2
Meeting the part A with the part a, B with b, and C with c respectively, mount a new barrier block assembly on the lens (fit it completely,
avoiding loose engagement or floating).
avoiding loose engagement or floating).
2-3-3. INSTALL NEW BARRIER BLOCK ASSEMBLY
Put the battery in the camera, and turn on the power (press twice to retract the lens-barrel).
Note: Check that the diaphragm of the barrier block assembly is not opened slightly or half-closed.
A
a
b
c
B
C
2-6
DSC-N2_L2
From the top spring position, cover new ornamental ring (A) on the 1 group frame.
Rotate the ornamental ring (A) over 90 degrees to spread the adhesive.
Note: Adhesive must not run off the lens-barrel.
Rotate the ornamental ring (A) over 90 degrees to spread the adhesive.
Note: Adhesive must not run off the lens-barrel.
Stiffen by leaving it for 60 minutes or more.
2-3-4. INSTALL NEW ORNAMENTAL RING (A)
Apply a thin coat of adhesive to the inside of ornamental ring (A).
Note: Use adhesive (Super X) or an equivalent article.
Note: Use adhesive (Super X) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
Ornamental ring (A)
Ornamental ring (A)
Adhesive
Position of adhesive spreading
Note: Refer after the adhesive of the removed ring.
Note: Refer after the adhesive of the removed ring.
Wipe off when the adhesive adheres outside
or edge side on the ring.
or edge side on the ring.
Adhesive
0.1mm
1.5-2.0mm
0.5mm
Spring
Ornamental ring (A)
Turn on and off the power to check the opening and closing of the barrier block with the camera in horizontal, up and down directions
respectively.
Further, check the zoom motion.
Rotate the ornamental ring (A) lightly to check that it is not removed.
respectively.
Further, check the zoom motion.
Rotate the ornamental ring (A) lightly to check that it is not removed.
Click on the first or last page to see other DSC-N2 (serv.man2) service manuals if exist.