DOWNLOAD Sony DSC-N2 (serv.man13) Service Manual ↓ Size: 7.09 MB | Pages: 66 in PDF or view online for FREE

DSC-N2_L2

2007B0200-1

  © 2007.2

Brazilian Model

The components identified by
mark  0  or dotted line with
mark 0 are critical for safety.
Replace only with part num-
ber specified.

Les composants identifiés par une
marque  0  sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.

— 2 —

DSC-N2_L2

Image device: 

9.15 mm (1/1.7 type) color CCD, 
Primary color filter

Total pixel number of camera: 

Approx. 10 300 000 pixels

Effective pixel number of camera: 

Approx. 10 054 000 pixels

Lens:

 Carl Zeiss Vario-Tessar 3

× zoom lens 

f = 7.9 - 23. 7 mm (38 -  114 mm when 
converted to a 35 mm still camera) F2.8 -  5.4

Exposure control: Automatic exposure, Manual 

exposure, Scene Selection (8 modes)

White balance: 

Automatic, Daylight, Cloudy, 

Fluorescent, Incandescent, Flash

File format (DCF compliant): 

Still images: Exif Ver. 2.21 JPEG compliant, 
DPOF compatible
Movies: MPEG1 compliant (Monaural)

Recording media:  Internal Memory 

(approx. 25 MB), "Memory Stick Duo"

Flash: 

Recommended distance (ISO set to Auto): 

Approx. 0.2 to 4.8 m (7 7/8 inches to 
189 inches) (W)/approx. 0.34 to 2.5 m 
(13 1/2 inches to 98 1/2 inches) (T)

Multi connector
USB communication: 

Hi-Speed USB (USB 2.0 compliant)

LCD panel: 

7.5 cm (3.0 type) TFT drive

Total number of dots:

 230 400 (960

×240) dots

Power:

 Rechargeable battery pack NP-BG1, 3.6 V

AC-LS5K AC Adaptor (not supplied), 4.2 V

Power consumption (during shooting):

 1.3 W

Operating temperature: 

0 to 40

°C ( 32 to 104° F)

Storage temperature:

 -20 to +60

°C (-4 to +140°F)

Dimensions:

 96.7

×61.1×22.7 mm (3 7/8×2 1/2×

29/32 inches) (W/H/D, excluding protrusions)

Mass:

 Approx. 185 g (6.5 oz) (including NP-BG1 

battery pack and wrist strap, etc.)

Microphone:

Monaural

Speaker:

 Monaural

Exif Print:

Compatible

PRINT Image Matching III:

Compatible
Compatible

PictBridge:

Power requirements:

AC 100 to 240 V, 50/60 Hz, 

2 W (BC-CSG)/ 2.6 W (BC-CSGB)

Output voltage: 

DC 4.2 V, 0.25 A

Operating temperature:

 0 to 40

°C ( 32 to 104°F)

Storage temperature: 

-20 to  +60

°C (-4 to  +140°F)

Dimensions:

 Approx. 62

×24×91 mm (2 1/2×

31/32

×3 5/8 inches) (W/H/D)

Mass:

 Approx. 75 g (2.7 oz)

Used battery:

 Lithium-ion battery

Maximum voltage: DC 4.2 V
Nominal voltage:  DC 3.6 V
Capacity:

3.4 Wh (960 mAh)

Design and specifications are subject to change 
without notice.

— 3 —

DSC-N2_L2

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

FLEXIBLE Circuit Board Repairing

•

Keep the temperature of the soldering iron around 270

°

C

during repairing.

•

Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).

•

Be careful not to apply force on the conductor when soldering
or unsoldering.

Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.

•

Unleaded solder melts at a temperature about 40

°

C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

•

Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

•

Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

— 4 —

DSC-N2_L2

1-1. Descrição da Função de Autodiagnóstico ······················· 1-1
1-2. Processo Após o Reparo do Erro do Flash ······················ 1-1
1-3. Método para Copiar ou Apagar os dados da Memória

interna   ··········································································· 1-2

1-4. Precaução para Reparação ·············································· 1-3
1-5. Precaução sobre Repado da placa SY-165  ·················· 1-4

2-1. Desmontagem··································································· 2-2
2-2. O Método de fixação do Bloco Central do Gabinete ······ 2-3
2-3. Método de Troca da Grade Montada   ·························· 2-4
2-4. Método de Troca do LSV-1100A ··································· 2-7

3-1. Diagrama em Bloco Geral (1/2) ······································ 3-1
3-2. Diagrama em Bloco Geral (2/2) ······································ 3-2
3-3. Diagrama em Bloco Power ············································· 3-3

4-1. Diagrama das Placas ··············································4-1
4-2. Diagramas Esquemático ·················································· 4-2
4-3. Placas de Circuito Impresso ·········································· 4-15

5-1. Vista Explodidas ······························································· 5-2
5-2. Lista de Peças Elétricas ···················································· 5-7

Section

Title

Page

Section

Title

Page