Sony DSC-M1 (serv.man3) Service Manual ▷ View online
— 3 —
DSC-M1
1.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
connections. Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
of deterioration. Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
— 4 —
DSC-M1
Checking supplied accessories.
Power cord (Main lead) (1)
(E model)
(E model)
0
1-769-608-11
Power cord (Main lead) (1)
(CH model)
(CH model)
0
1-782-476-13
Power cord (Main lead) (1)
(HK model)
(HK model)
0
1-783-374-11
Power cord (Main lead) (1)
(US/CND model)
(US/CND model)
0
1-790-107-22
Power cord (Main lead) (1)
(JE model)
(JE model)
0
1-790-732-12
Power cord (Main lead) (1)
(J model)
(J model)
0
1-791-637-13
Power cord (Main lead) (1)
(KR model)
(KR model)
0
1-823-947-11
Power cord (Main lead) (1)
(AUS model)
(AUS model)
0
1-827-945-11
AC-LM5/LM5A AC Adaptor (1)
0
1-477-730-61
CD-ROM
(USB Driver SPVD-012.1) (1)
2-187-885-01
(USB Driver SPVD-012.1) (1)
2-187-885-01
Cyber-shot station (UC-MA) (1)
1-818-873-11
1-818-873-11
A/V connecting cable (1)
1-765-080-62
1-765-080-62
USB cable (1)
1-827-754-21
1-827-754-21
Wrist strap (1)
2-320-915-01
2-320-915-01
2-pin conversion adaptor (1)
(JE model)
1-569-007-12
(JE model)
1-569-007-12
2-pin conversion adaptor (1)
(E model)
1-569-008-12
(E model)
1-569-008-12
“Memory Stick Duo” (32MB)(1)
(not supplied)
(not supplied)
Memory Stick Duo adaptor(1)
(not supplied)
(not supplied)
Rechargeable battery pack
(NP-FT1)(1)
(not supplied)
(NP-FT1)(1)
(not supplied)
Battery case (1)
(not supplied)
(not supplied)
Other accessories
2-320-916-01 MANUAL, INSTRUCTION (JAPANESE)(J)
2-320-916-11 MANUAL, INSTRUCTION (ENGLISH)
2-320-916-11 MANUAL, INSTRUCTION (ENGLISH)
(US/CND/E/HK/AUS/JE/CH)
2-320-916-21 MANUAL, INSTRUCTION (FRENCH)(CND)
2-320-916-31 MANUAL, INSTRUCTION (CHINESE)(E/HK/JE/CH)
2-320-916-41 MANUAL, INSTRUCTION (KOREAN)(KR/JE)
2-320-916-31 MANUAL, INSTRUCTION (CHINESE)(E/HK/JE/CH)
2-320-916-41 MANUAL, INSTRUCTION (KOREAN)(KR/JE)
2-320-917-01 MANUAL, INSTRUCTION (JAPANESE)((J)
• Abbreviation
CND : Canadian model
AUS : Australian model
CH
AUS : Australian model
CH
: Chinese model
HK
: Hong Kong model
KR
: Korea model
JE
: Tourist model
J
: Japanese model
Note :
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Note :
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Make sure that the following accessories are supplied with your camcorder.
— 5 —
DSC-M1
SELF-DIAGNOSIS FUNCTION
• NOTE FOR REPAIR
[Discharging of the FLASH unit’s charging capacitor]
The charging capacitor of the FLASH unit is charged up to the
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-T3 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the DSC-T3 is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k
To preparing the short jig. a small clip is attached to each end of a
resistor of 1 k
Ω
/1 W (1-215-869-11)
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
Discharging the Capacitor
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
Short circuits between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
Caution
Capacitor
Flash unit
Shorting jig
(1k
Ω
/ 1w)
— 6 —
DSC-M1
Display Code
C:32:01
C:13:01
Countermeasure
Turn off the main power then back on.
Replace the memory stick.
Format the memory stick with the DSC-T3.
Format the memory stick with the DSC-T3.
Cause
Trouble with hardware.
• The type of memory stick that cannot be
used by this machine, is inserted.
• Data is damaged.
• Unformatted memory stick is inserted.
• Unformatted memory stick is inserted.
Caution Display During Error
SYSTEM ERROR
MS ERROR
Self-diagnosis display
• C: ss: ss
• C: ss: ss
The contents which can be handled
by customer, are displayed.
by customer, are displayed.
• E: ss: ss
The contents which can be handled
by engineer, are displayed.
by engineer, are displayed.
[Description on Self-diagnosis Display]
Note:
Add the sentence as follows.
If other codes are displayed, service is required.
Please send the set to a specialized center.
If other codes are displayed, service is required.
Please send the set to a specialized center.
Display