Sony DSC-J20 Service Manual ▷ View online
DSC-J20
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR
The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
Strobe Board
R:1 k
Ω /1 W
Charging
Capacitor
Capacitor
Strobe Board
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
DSC-J20
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
DISASSEMBLY
1
#S1/#S2 X 5
6
1. Remove to numerical order (
1
to
6
) in the left figure.
Note
DISCHARGING OF THE CHARGING CAPACITOR
1
X-2584-816-1 FRONT COVER ASSY (P) (PINK)
1
X-2584-817-1 FRONT COVER ASSY (L) (BLUE)
1
X-2584-818-1 FRONT COVER ASSY (W) (WHITE)
1
X-2584-819-1 FRONT COVER ASSY (B) (BLACK)
1
X-2585-092-1 FRONT COVER ASSY (S) (SILVER)
2
A-1884-884-A LCD MODULE UNIT (Note 2)
3
A-1884-883-A SW BOARD, COMPLETE (Note 2)
4
4-431-554-01 UI
BUTTON
5
X-2584-820-1 REAR COVER ASSY (P) (PINK)
5
X-2584-821-1 REAR COVER ASSY (L) (BLUE)
5
X-2584-822-1 REAR COVER ASSY (W) (WHITE)
5
X-2584-823-1 REAR COVER ASSY (B) (BLACK)
5
X-2585-097-1 REAR COVER ASSY (S) (SILVER)
6
X-2584-824-1 MIDDLE COVER ASSY (P) (PINK)
6
X-2584-825-1 MIDDLE COVER ASSY (L) (BLUE)
6
X-2584-826-1 MIDDLE COVER ASSY (W) (WHITE)
6
X-2584-827-1 MIDDLE COVER ASSY (B) (BLACK)
6
X-2585-099-1 MIDDLE COVER ASSY (S) (SILVER)
#S1
4-431-613-01
SCREW_M_1.4_4.5_SVR_AB (Note 1)
#S2
4-431-612-01
SCREW_M_1.4_4.5_BLK_AB (Note 1)
#S3
4-274-002-01 SCREW_TP_1.4_3_SVR_AB
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#S1 (Silver)
BLACK
#S2 (Black)
PINK/BLUE/WHITE/
SILVER
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed is different according to
the cabinet's color.
For the combination of cabinet's color and screw,
please refer to Table 2-1.
the cabinet's color.
For the combination of cabinet's color and screw,
please refer to Table 2-1.
Bottom View
Right View
Left View
#S1
#S2
#S2
#S1
#S2
#S2
#S1
#S2
#S2
Note2: Refer to “Assembly-1: Handling Method for the Flexible
Boards of the LCD Module and SW Board.”.
A
A
2
5
4
2
(Note 2)
3
3
(Note 2)
5
6
1
1
4
#S1
#S2
(Note 1)
#S2
(Note 1)
#S1
#S2
(Note 1)
#S2
(Note 1)
#S1
#S2
(Note 1)
#S2
(Note 1)
#S3
#S3
Chassis Section
(See Page 2-4)
When assembling, adjust the position.
2 (Claws)
1 (Claws)
1 (Claw)
4 (Claw)
4 (Claw)
4 (Claw)
5 (Claw)
5 (Claws)
6
3
#S3 X 1
Back View
#S3
5
#S3 X 1
Front View
#S3
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2012.04
DSC-J20
2-4
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
2-1-2. CHASSIS SECTION
ns: not supplied
DISASSEMBLY
1. Remove to numerical order (
1
to
5
) in the left figure.
51
A-1884-889-A SPEAKER ASSY (Note 1)
52
A-1884-891-A MAIN BOARD, COMPLETE
53
4-431-563-01
PLATE, MICROPHONE GROUND
54
A-1884-890-A MICROPHONE ASSY (Note 2)
55
4-431-583-01
SHAFT, BATTERY LID
56
4-431-565-01
LID (P), BATTERY (PINK)
56
4-431-566-01
LID (L), BATTERY (BLUE)
56
4-431-568-01
LID (W), BATTERY (WHITE)
56
4-431-569-01
LID (B), BATTERY (BLACK)
56
4-434-380-01
LID (S), BATTERY (SILVER)
57
4-431-570-01
KNOB (P), BATTERY LID LOCK (BLUE, PINK)
57
4-431-571-01
KNOB (W), BATTERY LID LOCK
(BLACK, WHITE, SILVER)
58
4-431-584-01
SPRING, BATTERY LID
59
X-2584-828-1 PLATE ASSY, BATTERY COVER
60
4-431-592-01
COVER (P), DC (PINK)
60
4-431-593-01
COVER (L), DC (BLUE)
60
4-431-594-01
COVER (W), DC (WHITE)
60
4-431-595-01
COVER (B), DC (BLACK)
60
4-434-381-01
COVER (S), DC (SILVER)
61
4-274-009-01 SHAFT,
STRAP
62
X-2584-829-1 CHASSIS
ASSY
63
A-1884-885-A STROBE PC BOARD ASSY
63
A-1884-885-A STROBE PC BOARD ASSY (EXCEPT SILVER)
63
A-1890-399-A STROBE PC BOARD ASSY (SILVER)
64
1-856-181-11
OPTICAL UNIT (BE0032)
65
A-1939-751-A
CCD
BLOCK
ASSY
F1
1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
F2
1-576-415-11 FUSE, MICRO (1608 TYPE) (2A/32V)
#S3
4-274-002-01 SCREW_TP_1.4_3_SVR_AB
#S4
4-274-013-01 SCREW_TP_1.2_3.5_SVR_AB
2
#S3 X 2
Back View
#S3
Note
Note1: Refer to “Assembly-2: Routing and Soldering Method of the
Speaker Harnesses.”.
Note2: Refer to “Assembly-3: Soldering Method of the Microphone
Harnesses.”.
4
#S3 X2
4
Remove soldering
→ #S3 X4 → Microphone Ground Plate (
4
)
Front View
#S3
#S3
Soldering point
Top View
#S3
4
2
ns
5
63
62
3
61
53
4
52
1
64
65
60
51
(Note 1)
54
(Note 2)
55
56
57
59
58
#S3
#S3
F1
F2
ns
#S4
ns
#S3
#S3
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2013.04
DSC-J20
2-5E
ACCESSORIES
901
902
903
904
905
Note: This unit has no bundled CD-ROM.
Contents included in the CD-ROM will be supplied to customers as
follows.
Contents included in the CD-ROM will be supplied to customers as
follows.
・ User Guide (HTML)
-
You can access to the URL of support site described in the Instruc-
tion Manual.
-
All of the contents in the User Guide are included in the Instruction
Manual or built-in guide.
・ Application Software
-
By connecting this unit and Windows PC with the USB cable, the
application software [PlayMemories Home Lite version] can be
installed on the PC from the unit.
installed on the PC from the unit.
-
In case of using the extended version, install “Expanded Feature”
via Internet.
-
If a customer requests the CD-ROM, consult with each Head
Quarters.
Ref. No. Part No.
Description
901
1-487-523-31
Battery charger BC-CSN
902
1-837-783-21
Dedicated USB cable
903
2-050-981-01 Wrist
strap
904
4-425-247-11
Instruction Manual (SIMPLIFIED CHINESE)
905
1-853-124-51
Rechargeable battery pack NP-BN/NP-BN1
Click on the first or last page to see other DSC-J20 service manuals if exist.