DOWNLOAD Sony DSC-HX50 / DSC-HX50V (serv.man2) Service Manual ↓ Size: 7.87 MB | Pages: 43 in PDF or view online for FREE

DSC-HX50/HX50V_L2

1-18

19. Turn the Gear B counterclockwise to set the lens unit in the retracted state, and then remove the Gear B.

 

Gear B

Gear B

20.  Fit the DC Motor Worm Assy with the boss and secure it with two screws.
21. Install Gear WH, Gear A, and then Gear B.

 

Screws

Boss

DC Motor Worm Assy

Gear B

Gear A

Gear WH

DC Motor Worm Assy

22.  Secure the Rear Lens Assy with five screws.
23.  Connect the three sensors on the LF-2038 Flexible Board.

 

Sensor

Screws

Screws

Sensors

LF-2038 Flexible Board

Rear Lens Assy

24.  Fix the LF-2038 Flexible Board to the groove and the hole.
25.  Connect the flexible board to the connector on the LF-2038 Flexible Board.

 

Connector

Groove

Hole

Flexible Board

LF-2038 Flexible Board

DSC-HX50/HX50V_L2

1-19

26.  Solder the DC Motor Worm Assy at two locations shown below to secure the LF-2038 Flexible Board to the DC Motor Worm Assy.

 

Solders

DC Motor Worm Assy

27.  Fix the FPC Retainer to the two projections and then to the claw.
28.  Fix the FG Retainer to the boss and then to the claw.
29.  Fix the Z Retainer to the two projections and then to the claw.

 

Claw

Claw

Boss

Claw

FPC Retainer

Z Retainer

Projections

Projections

FG Retainer

Lower

Inspect it as follows when you exchange parts in the lens block.

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

1

2

3

4

5

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

DSC-HX50/HX50V_L2

1-20E

Focus check
1

  Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

  Shoot setting

 

(1)  Paste the chart.

 

•  Chart should be on the flat wall.

 

•  Illuminance level in the chart should be the same.

 

•  Make the tripod’s height and the center of the chart to the same height.

 

•  Enough space needed for shooting.

 

(2)  Set the camera.

 

•  Set [P] mode

 

•  Set [Maximum] size

 

•  Set ISO lowest level

 

•  Set Steady Shot [OFF]

 

•  Set Flash [OFF]

 

(3)  Set the camera on a tripod.

 

(4)  Adjust the position of the camera and the chart.

 

1. Set the zoom position of the camera at Wide end.

 

2. Attach the mirror onto the center of the chart.

 

    * The mirror should not tilt on the chart.

 

3. Set the camera to display the chart on LCD like in the following picture.

 

4. Adjust the camera position to the center of the chart.

 

    * Adjust the tripod height and the position (Lateral direction).

 

5. Adjust the camera angle to the frame of the chart with tripod.

 

    Remove the mirror.

3

  Shooting

      (1)  Set [Self-Timer]
      (2)  Shot
4

  Check the shot image.

      (1)  Check the shot image on PC.
 

100% Display (Display at the same magnification of its Pixel.)

 

Compare the image with the sample you set.

      No extreme focus blurring
      It should be distinguished the black and white by the sharpness between them.
      If it is in NG level, replace the lens unit.

<Reference>
•     How to Print the Chart
      Print “Focus-Chart_A3.pdf” with printer.
      Print at the same magnification (It means 100 % size).
      Check the settings of printer to print in proper size.
•     Check of chart size.
      Make charts together and check if the size of charts is the following size.
      * The chart consists of 2 pcs.

DSC-HX50/HX50V_L2

2-1

Follow the disassembly in the numerical order given.

• CD-1005 Flexible Board
• LF-2038 Flexible Board

• MS-1013 Board
• BT-2006 Flexible Board
• MS-505 Flexible Board

• RL-1011 Board
• FL-200 Flexible Board
• RL-1012 Flexible Board
• SH-1006 Flexible Board
• ST-1014 Flexible Board

• ST-1007 Flexible Board

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 

one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not sup-

plied.

•  Due to standardization, replacements in the parts list may be different from the parts 

specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: μ, for example:
 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

The components identified by mark 0 

or dotted line with mark 0 are critical for 

safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant 
le numéro spécifié.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

【使用上の注意】 

• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。

• 抵抗の単位Ωは省略してあります。
金  被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。

0印の部品，または0印付の点線で囲ま
れた部品は，安全性を維持するために，
重要な部品です。
従って交換時は，必ず指定の部品を使用
してください。

•  外装部品色表示
 

例：

 

(SILVER) ：セットの色を表す。

 

(Silver)  ：部品の色を表す。

• Abbreviation
 AUS : 

Australian 

model

 BR  : 

Brazilian 

model

  CH 

: Chinese model

  CND  : Canadian model
  HK 

: Hong Kong model

  J 

: Japanese model

 KR  : 

Korea 

model

  RU 

: Russian model

 TW  : 

Taiwan 

model

Right View

Left View

Front View

Bottom View

Top View

Back View