DOWNLOAD Sony DSC-HX400 / DSC-HX400V Service Manual ↓ Size: 7.51 MB | Pages: 50 in PDF or view online for FREE

DSC-HX400/HX400V

4-22

(20)  Connect the 5th Assy Flexible Board to the connector on the Main Flexible Board.

 

Main Flexible Board

5th Assy
Flexible Board

(21)  Stick the Shutter Flexible Board.

 

Adhesive Tape

Shutter Flexible Board

Main Flexible Board

(22)  Solder the Main Flexible Board and the Shutter Flexible Board.
(23)  Stick the Polyester Tape.

 

Shutter Flexible Board

Main Flexible Board

Solders

Polyester Tape

(24)  Perform the Flange Back Adjustment after the assembling.

DSC-HX400/HX400V

4-23

 

Inspect it as follows when you exchange parts in the lens block.
1

2

4

5

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

下図は当機種と本体の形状が異なります。

As for the figure below, this model and the shape
of the main body are different. 

DSC-HX400/HX400V

4-24

Focus check
1

  Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

  Shoot setting

 

(1)  Paste the chart.

 

•  Chart should be on the flat wall.

 

•  Illuminance level in the chart should be the same.

 

•  Make the tripod’s height and the center of the chart to the same height.

 

•  Enough space needed for shooting.

 

(2)  Set the camera.

 

•  Set [P] mode

 

•  Set [Maximum] size

 

•  Set ISO lowest level

 

•  Set Flash [OFF]

 

(3)  Set the camera on a tripod.

 

(4)  Adjust the position of the camera and the chart.

 

1. Set the zoom position of the camera at Wide end.

 

2. Attach the mirror onto the center of the chart.

 

    * The mirror should not tilt on the chart.

 

3. Set the camera to display the chart on LCD like in the following picture.

 

4. Adjust the camera position to the center of the chart.

 

    * Adjust the tripod height and the position (Lateral direction).

 

5. Adjust the camera angle to the frame of the chart with tripod.

 

    Remove the mirror.

3

  Shooting

      (1)  Set [Self-Timer]
      (2)  Shot
4

  Check the shot image.

      (1)  Check the shot image on PC.
 

100% Display (Display at the same magnification of its Pixel.)

 

Compare the image with the sample you set.

      No extreme focus blurring
      It should be distinguished the black and white by the sharpness between them.
      If it is in NG level, replace the lens unit.

<Reference>
•     How to Print the Chart
      Print “Focus-Chart_A3.pdf” with printer.
      Print at the same magnification (It means 100 % size).
      Check the settings of printer to print in proper size.
•     Check of chart size.
      Make charts together and check if the size of charts is the following size.
      * The chart consists of 2 pcs.

DSC-HX400/HX400V

5-1

For adjusting these models, the Adjust manual and the Adjust station are required.

It is the software to start up Adjust manual for each model.
The installer of the Adjust station and the installation manual are attached, be sure to confirm the contents of them.

It is the software to adjust and check digital cameras and camcorders for service.  
The installer of the Adjust manual and the installation manual are attached, be sure to confirm the contents of them.

Note 1:  Be sure to install Adjust station first.
Note 2:  To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
 

Install the Adjust manual of the DSC-WX50 series in advance.

これらの機種で調整を行なうには，アジャストマニュアルとアジャストステーションが必要です。

アジャストステーションとは

機種別のアジャストマニュアルを起動するためのソフトウェアです。
アジャストステーションのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認して
ください。

アジャストマニュアルとは

デジタルカメラ及びカムコーダのサービス用の調整ソフトウェアで，調整及び各種動作確認を行うことが可能です。
アジャストマニュアルのインストーラと一緒に，インストレーションマニュアルが付いていますので，内容を必ず確認してく
ださい。

注意1：  インストールは必ず Adjust station を先に行なってください。
注意2：  この機種で仕向け設定を行うには，DSC-WX50シリーズの  Adjust  manual  がインストールされている必要

があります。

   

先に DSC-WX50 シリーズの Adjust manual をインストールしてください。