Sony DSC-H5 (serv.man2) Service Manual ▷ View online
DSC-H5_L2
2-4E
2. DISASSEMBLY
2. DISASSEMBLY
SY-150
SY-150
MS-
305
305
2
3
1
1
Two claws
2
Flexible board (from the LCD module)
3
EVF section
4
8
5
1
2
3
6
7
1
4
5
6
2
3
1
Battery connector
2
From the loudspeaker
3
JK-306 flexible board
4
Two tapping screws (M1.7x4)
5
Flexible flat cable (MS-030)
6
SW-478 flexible board
7
CK-161 flexible board
8
SY-150 board
1
Flexible flat cable (MS-030)
2
Two tapping screws (M1.7x4)
3
MS-305 board
4
Battery connector
5
Three claws
6
Battery terminal board
A
B
1
Turn the flexible board.
2
Tapping screw (M1.7x5)
3
Lens section
1
3
1
2
6
8
7
1
9
2
1
Two tapping screws (M1.7x4)
2
Control switch block
1
Tapping screw (M1.7x4)
2
Microphone holder
3
Microphone cushion (B)
4
Microphone
5
Microphone cushion
6
Tapping screw (M1.7x4)
7
AF-105 flexible board
8
Tapping screw (M1.7x4)
9
AF holder
2
3
4
5
2
1
Claw
2
Three harnesses (HA-001) (Red, White, Blue)
3
Open the ST cover in the direction of the arrow.
4
ST section
3
4
1
HELP 05
HELP 08
HELP 06
HELP 04
HELP 07
HELP 02
HELP 03
Refer to page 2-1 "DISCHARGING
OF THE FLASHLIGHT POWER
SUPPLY CAPACITOR, when
discharging the capacitor.
OF THE FLASHLIGHT POWER
SUPPLY CAPACITOR, when
discharging the capacitor.
DSC-H5_L2
HELP
HELP
Disassembling and assembling procedures that require attention are described here.
HELP 02
When installing the loudspeaker, route the harnesses of the loudspeaker as shown in the figure.
HELP 01
When attaching the fuse replacement caution label to the SY-150 board,
cover the harness of the loudspeaker with the fuse replacement caution label.
cover the harness of the loudspeaker with the fuse replacement caution label.
Bend the harnesses of the
loudspeaker at the route
of the connector.
loudspeaker at the route
of the connector.
Harnesses of
the
the
loudspeaker
L
oudspeaker (1.0cm)
Harnesses of
the
the
loudspeaker
Fuse replacement
caution label
caution label
When installing the battery terminal board, route the harnesses of the
battery terminal board as shown in the figure.
battery terminal board as shown in the figure.
The harnesses in the area A
must be kept below surface B.
must be kept below surface B.
The harnesses in the area C must be
kept within the D lines.
Bend the harness at portion E so that
the harness runs along line F.
kept within the D lines.
Bend the harness at portion E so that
the harness runs along line F.
Harnesses of the battery
terminal board
terminal board
Battery terminal
board
board
A
D
F
E
C
surface B
Harnesses of the battery
terminal board
terminal board
HELP 03
DSC-H5_L2
HELP
HELP 05
HELP 06
Harness (HA-004) (Blue) ,
Harness (HA-004)(W
hite
),
Harness (HA-004) (Red)
ST section
Red
ST-144 board
ST-142 board
Red
White
White
Blue
Blue
1
Harness (H-004) (Red)
2
Harness (H-004) (White)
3
Harness (H-004) (
Blue
)
4
Flash unit, ST-144 board
5
Apply the soldering in three points.
6
ST-142 board
7
Apply the soldering in three points.
8
ST cover
9
Two
claws
q;
Tapping screw (M1.7x4)
4
7
5
q;
HELP 04
When installing the ST section, route the
Harness (HA-004) (Blue) ,Harness (HA-004)(White),
and Harness (HA-004) (Red) as shown in the figure.
Harness (HA-004) (Blue) ,Harness (HA-004)(White),
and Harness (HA-004) (Red) as shown in the figure.
Route the harnesses with the ST cover closed.
When installing the ST section, route the
Harness (HA-004) (Blue) ,Harness (HA-004)(White),
and Harness (HA-004) (Red) as shown in the figure.
Harness (HA-004) (Blue) ,Harness (HA-004)(White),
and Harness (HA-004) (Red) as shown in the figure.
Solder each harness according to the color
( Red, White, Blue) as shown in the figure.
( Red, White, Blue) as shown in the figure.
Solder each harness according to the color
( Red, White, Blue) as shown in the figure.
( Red, White, Blue) as shown in the figure.
ST section
9
8
6
3
Blue
2
White
1
Red
Harness (HA-004) (W
hite
)
Harness (HA-004) (Blue)
Harness (HA-004) (Red)
DSC-H5_L2
HELP
HELP 07
Install the microphone tilted as
shown in the figure below.
shown in the figure below.
HELP 08
When removing the lens ring, remove the screw and strap sheet metal (R) first.
Slide the cap lever in the direction of arrow
Slide the cap lever in the direction of arrow
A
while taking care that the cap
lever is not caught on the notch of the lens ring.
Remove the lens ring by turning it in the direction of arrow
Remove the lens ring by turning it in the direction of arrow
B
.
2
Strap sheet metal (R)
1
Tapping screw (M1.7x4)
Microphone cushion
Microphone cushion (B)
Microphone
Microphone holder
Microphone cushion
Microphone
cushion (B)
cushion (B)
Microphone
Microphone
holder
holder
3
Lens ring
Cap lever
Lens ring
Notch of the
lens ring
B
A
Cap lever
Click on the first or last page to see other DSC-H5 (serv.man2) service manuals if exist.