Sony DSC-H300 (serv.man2) Service Manual ▷ View online
DSC-H300_ADJ
5-5
The adjustment is finished normally.
OB VAL:
R OFFS:
G OFFS:
B OFFS:
G OFFS:
B OFFS:
0x07a8
0x07a9
0x07aa
0x07a9
0x07aa
Limit:4 3840
Time:2426
FINISH
T
OK
Fig. 5-3-10
The adjustment is complete.
Adjustment order
Screen display
5-3-4. OB Adjustment
The OB (Optically Black) Adjustment order is as follows.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (All black). (Fig. 5-3-9)
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “OB CLBT (BLACK)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-10)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-10)
Press the “ (Playback)” button to return to
adjustment menu.
Finished normally.
Finished abnormally.
In case of the indication other than that shown in
Fig. 5-3-10 appears on the screen, confirm the
adjusting environment and readjust.
Fig. 5-3-10 appears on the screen, confirm the
adjusting environment and readjust.
Confirm the indication
on the screen.
Camera
Equipment required: Cover camera lens
(All black)
Black cloth
Fig. 5-3-9
5-3-3. Focus Adjustment
The Focus Adjustment order is as follows.
Note:
When using the Flange back adjustment jig, take care of the following points:
When using the Flange back adjustment jig, take care of the following points:
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room illumination only.
• Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room illumination only.
• Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1) Install the Flange back adjustment jig so that the distance between
it and the front of lens of camera is 10 mm or less (Tele end).
Note:
Take care not to hit the Flange back adjustment jig when extending the lens.
Take care not to hit the Flange back adjustment jig when extending the lens.
2) Make the height of Flange back adjustment jig and the camera equal.
3) Check that the center of chart meets the center of shot image screen.
Illuminance = 1000 ± 200 lx
Adjustment order
Screen display
The adjustment is finished normally.
******
IN FOCUS
******
0,-1,552
1,0,585
2,-1,660
3,0,743
4,0,810
5,0,882
6,-1,945
7,2,1086
8,0,1221
9,0,1347
10,1,1608
1,0,585
2,-1,660
3,0,743
4,0,810
5,0,882
6,-1,945
7,2,1086
8,0,1221
9,0,1347
10,1,1608
11,0,1683
12,1,1751
13,0,1802
14,0,1840
15,0,1827
16,0,1745
17,1,1565
18,0,1330
19,0,984
20,0,433
12,1,1751
13,0,1802
14,0,1840
15,0,1827
16,0,1745
17,1,1565
18,0,1330
19,0,984
20,0,433
Getsum 0x3F
OK
Fig. 5-3-7
The adjustment is complete.
The adjustment is finished abnormally.
******
INF FOCUS
******
Focus Over Range Large ..
Cali Er
NG
Fig. 5-3-8
Malfunction of Focus
adjustment result
adjustment result
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flange back adjustment jig. (Fig. 5-3-6)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-8)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-8)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “FOCUS (Infinity)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-7)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-7)
Press the “ (Playback)” button to return to
adjustment menu.
Finished normally.
Finished abnormally.
Confirm the indication
on the screen.
Flange back adjustment jig
10 mm or less (Tele end)
Camera
Equipment required: Flange back adjustment jig
Fig. 5-3-6
DSC-H300_ADJ
5-6
Adjustment order
Screen display
Setting Light Src value.
Setting Light Src value.
5-3-5. WB/AGC Adjustment
The WB/AGC (White Balance/Analog Gain Control) Adjustment order
is as follows.
is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
LimitR:312 579
LimitB:338 628
LimitB:338 628
MEAN G
DayLig
R Gain
G Gain
B Gain
G Gain
B Gain
25854
32018
25610
75923
25610
75923
Time:16585
Move OK...
OK
Fig. 5-3-13
The adjustment is complete.
The adjustment is finished abnormally.
Limit:234 276
49 8, 191
49 8, 191
ZPos :
WLuma:
LS:-1 3:
OC:
63
OC :
Entry :
Gain :
AGC :
Gain :
AGC :
0x002e
0x0101
0x0101
OK
NG
Cali Er
T
Fig. 5-3-14
Malfunction of WB/AGC
adjustment result
adjustment result
5-3-6. MeShut26 Adjustment
The MeShut26 (Mechanical Shutter 26) Adjustment order is as follows.
Note:
Perform the MeShut26 Adjustment after those performed in 5-3-4 to 5-3-5.
Perform the MeShut26 Adjustment after those performed in 5-3-4 to 5-3-5.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Iris No:
1
Time:605
OK
FINISH...
Fig. 5-3-16
The adjustment is complete.
Adjustment order
Screen display
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Confirm the indication
on the screen.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-14)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-14)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “WB/AGC (LV10)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-13)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-13)
Press the “ (Playback)” button to return to
adjustment menu.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item to “WB/AGC (LV10)”,
and press the “ (Playback)” button. Press the Control button “ v ” “ V ” to change selected item
to “Light Src”, and press the Control button “ b ” “ B ” to set the value as “00002”, and press the
Control button “ z ”. (Fig. 5-3-12)
and press the “ (Playback)” button. Press the Control button “ v ” “ V ” to change selected item
to “Light Src”, and press the Control button “ b ” “ B ” to set the value as “00002”, and press the
Control button “ z ”. (Fig. 5-3-12)
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-11)
Finished normally.
Finished abnormally.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the indication other than that shown in
Fig. 5-3-16 appears on the screen, confirm the
adjusting environment and readjust.
Fig. 5-3-16 appears on the screen, confirm the
adjusting environment and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “MeShut26 (LV13)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-16)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-16)
Press the “ (Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-15)
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less (Tele end)
Black cloth
Camera
Fig. 5-3-11
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less (Tele end)
Black cloth
Camera
Fig. 5-3-15
Disable
00001
LightSrc
00002
P1RRatio
01078
P1BRatio
01031
P2RRatio
01458
P2BRatio
00619
Fig. 5-3-12
DSC-H300_ADJ
5-7
5-3-7. MeShut80 Adjustment
The MeShut80 (Mechanical Shutter 80) Adjustment order is as follows.
Note:
Perform the MeShut80 Adjustment after those performed in 5-3-4 to 5-3-6.
Perform the MeShut80 Adjustment after those performed in 5-3-4 to 5-3-6.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Limit:550 678
CAPNUM :
DRAFT_G:
Iris No:
STILL_G:
MainDly:
SubDly :
MainDly:
SubDly :
79
76
76
622
442
442
2
2
2
Time:14958
OK
FINISH..
.
Fig. 5-3-18
The adjustment is complete.
The adjustment is finished abnormally.
...Iris or LV NG
CAPNUM :
DRAFT_G:
Iris No:
STILL_G:
MainDly:
SubDly :
MainDly:
SubDly :
2
2
Time:686
Calib Er
..
NG
Fig. 5-3-19
Malfunction of MeShut80
adjustment result
adjustment result
Adjustment order
Screen display
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-19)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-19)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “MeShut80 (LV14)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-18)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-18)
Press the “ (Playback)” button to return to
adjustment menu.
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-17)
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less (Tele end)
Black cloth
Camera
Fig. 5-3-17
Adjustment order
Screen display
5-3-8. Dark DP Adjustment
The Dark DP (Dead Pixel) Adjustment order is as follows.
Note:
Perform the Dark DP Adjustment after those performed in 5-3-4 to 5-3-7.
Perform the Dark DP Adjustment after those performed in 5-3-4 to 5-3-7.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Cap Raw ...
Threshold :
Find DP NUM
Find DP NUM
Time (Sec)
DARK DPC
512
4
13
1
FINISH ....
OK
Fig. 5-3-21
The adjustment is complete.
The adjustment is finished abnormally.
Cap Raw ...
Threshold :
Find DP NUM
Find DP NUM
Time (Sec)
DARK DPC
602
99
41
1
FINISH ....
NG
Fig. 5-3-22
Malfunction of Dark DP
adjustment result
adjustment result
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-22)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-22)
In this case, confirm the adjusting environment
and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “Dark DPC (LV10)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-21)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-21)
Press the “ (Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-20)
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less (Tele end)
Black cloth
Camera
Fig. 5-3-20
DSC-H300_ADJ
5-8
Adjustment order
Screen display
5-3-9. Light/S.S Adjustment
The Light/S.S (Light Dead Pixel/Slow Shutter Dead Pixel)
Adjustment order is as follows.
Adjustment order is as follows.
Note:
Perform the Light/S.S Adjustment after those performed in 5-3-4 to 5-3-8.
Perform the Light/S.S Adjustment after those performed in 5-3-4 to 5-3-8.
The adjustment is finished normally.
OK
Fig.
5-3-25
The adjustment is complete.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the indication other than that shown in
Fig. 5-3-25 appears on the screen, confirm the
adjusting environment and readjust.
Fig. 5-3-25 appears on the screen, confirm the
adjusting environment and readjust.
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “Light S.S (BLACK)”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
*1 If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
*2 It takes approximately 15 minutes or more on this adjustment.
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
*1 If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
*2 It takes approximately 15 minutes or more on this adjustment.
In case of the adjustment
is finished normally, the
adjustment completion
indication appears on the
screen. (Fig. 5-3-25)
* The Self-timer lamp
lights up. (Fig. 5-3-24)
is finished normally, the
adjustment completion
indication appears on the
screen. (Fig. 5-3-25)
* The Self-timer lamp
lights up. (Fig. 5-3-24)
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (All black) (Fig. 5-3-23)
Restart the camera.
Fig. 5-3-24
Self-timer lamp
Camera
Equipment required: Cover camera lens
(All black)
Black cloth
Fig. 5-3-23
5-3-10. Flash WB Adjustment
Preparing the Flash Adjustment Box
A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as shown below.
1) Provide woody board A, B, C and D of 15 mm thickness.
2) Apply black mat paint to one side of woody board A, B and D.
3) Attach background paper (J-2501-130-A) to woody board C.
4) Assemble so that the black sides and the background paper side of woody board A, B, C and D are internal. (Fig. 5-3-27)
Woody board A
Woody board B
Woody board B
Woody board C
Woody board A
Woody board D
Front of the lens
L = 500 mm
L
Camera
Woody board A (2)
400 mm
Woody board B (2)
370 mm
Woody board C (1)
700 mm
513 mm
513 mm
700 mm
Woody board D (1)
370 mm
370 mm
700 mm
730 mm
100 mm
120 mm
Fig.
5-3-26
Fig. 5-3-27
Click on the first or last page to see other DSC-H300 (serv.man2) service manuals if exist.