Sony DSC-H100 (serv.man2) Service Manual ▷ View online
DSC-H100_ADJ
5-9
Adjustment order
Screen display
The adjustment is finished normally.
Succes
OK
Angle:3.3 deg.
AF Luma:0962
AF Luma:0962
Fig. 5-3-32
The adjustment is complete.
The adjustment is finished abnormally.
Success
NG
Angle:3.3 deg.
AF Luma:1169
AF Luma:1169
Fig. 5-3-33
Malfunction of Flash WB
adjustment
adjustment
The Flash WB Adjustment order is as follows.
Note:
Perform the Flash WB Adjustment after those performed in 5-3-4 to 5-3-5.
Perform the Flash WB Adjustment after those performed in 5-3-4 to 5-3-5.
Confirm the indication
on the screen.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-33)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-33)
In this case, confirm the adjusting environment
and readjust.
n
Press the Control button “ b ” “ B ” and “ v ” “ V ” to change selected item. Choose “FLASH WB”,
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
press the Control button “ z ”, select “OK”, and press the Control button “ z ” to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-32)
Press the “ (Playback)” button to return to
adjustment menu.
the adjustment completion indication appears
on the screen. (Fig. 5-3-32)
Press the “ (Playback)” button to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flash Adjustment Box. (Fig. 5-3-31)
Finished normally.
Finished abnormally.
5-3-11. AF Lamp Check
The AF Lamp check order is as follows.
Setting conditions
• Project images on a dark wall surface.
• Distance between wall surface and camera = approx. 1 m
• The wall surface and the camera are face to face.
• Distance between wall surface and camera = approx. 1 m
• The wall surface and the camera are face to face.
1) Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the
Adjustment Mode” (Page 5-3).
Adjustment Mode” (Page 5-3).
Equipment required:
Wall surface
Approx.
1 m
Camera
Project images on
a dark wall surface
a dark wall surface
Fig. 5-3-34
2) Place the camera in front of a dark wall surface face to face.
3) Press the Control button “ b ” “ B ” and “ ▲ ” “ ▼ ” to change selected item. Choose “AFLAMP”, press the Control button “ z ”, select “OK”,
and press the Control button “ z ” to start.
Note:
If the check is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the check. (Page 5-3)
A guide frame is displayed on the LCD screen and the AF lamp lights.
Manipulate the camera so that the auxiliary light on the wall surface comes to the center of the guide frame.
5-3-12. Lens Option
Lens Option Setting order is as follows.
1) Check that the camera is on the adjustment mode.
Note:
For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
2) Press the Control button “ b ” “ B ” and “ v ” “ V ”to change selected item. Choose “Lens Option”,
press the “
(Playback)” button to choose item.
Note:
If the setting is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the setting. (Page 5-3)
3) Press the Control button “ V ” to “Enable LDC” item after press the Control button “ B ” to set enable (00001).
Press the Control button “ V ” to “Enable LSC” item after press the Control button “ B ” to set enable (00001).
Press the Control button “ V ” to “Enable OIS” item after press the Control button “ z ” to set enable (00002).
Press the Control button “ V ” to “Enable OIS” item after press the Control button “ z ” to set enable (00002).
Final Press the “
(Playback)” button to return to adjustment mode, then press the Control button “ z ”,
select “OK” and press the Control button “ z ” to start.
Note:
LDC : Lens Distortion Correction
LSC : Lens Shading Correction
OIS : Optical Image Stabilizer
4) Confirm the indication on the screen.
When the setting is finished, the setting completion indication appears on the screen. (Fig. 5-3-37)
Press the “
Press the “
(Playback)” button to return to adjustment menu.
LDC
ON
LSC
ON
OIS
ON
Fig.
5-3-37
4) Confirm the indication on the screen.
If OK appears for all check items, press the “
(Playback)” button
to return to adjustment menu. (Fig. 5-3-35)
OK
Angle:3.3 deg.
AF Luma:0485
AF Luma:0485
Fig. 5-3-35
If NG appears for more than one check item, confirm the adjusting
environment and recheck. (Fig. 5-3-36)
environment and recheck. (Fig. 5-3-36)
NG
Fig. 5-3-36
DSC-H100_ADJ
5-10
5-3-13. Set Language Destination
Note:
Finish all of the adjustment except for the Language Destination setting.
Once the Language Destination setting is finished, it cannot be reset.
Once the Language Destination setting is finished, it cannot be reset.
USB Driver and Service Tool
Put the two folders “USB Driver” and “Service Tool” downloaded in “5-1-5. Setting the Adjustment Mode” (Page 5-3) in any place of the PC.
The procedure of installing a USB Driver is as follows.
1) Connect the camera started up with the Adjustment mode, and the PC with a Dedicated USB Cable.
2) Install the USB Driver according to the guidance on the screen.
Connecting USB to PC
Connect the equipment as shown below. (Fig. 5-3-38)
Dedicated USB Cable
Personal Computer
1
To a USB jack of the PC
2
To the
(USB)/A/V OUT
jack
jack
Fig.
5-3-38
Starting up the Service Tool
Double click the “ServiceTool_Ver[][][].exe” in the “Service Tool” folder to start up the Service Tool. (Fig. 5-3-39)
Fig.
5-3-39
The setting is finished normally.
Fig. 5-3-40
The setting is complete.
Screen display
The setting is finished abnormally.
Fig. 5-3-41
Malfunction of Set
Language Destination
result
Language Destination
result
Example:
Please Plug in
USB!
Fig. 5-3-42
Malfunction of Set
Language Destination
result
Language Destination
result
Example:
Serial No.
Length ERROR
Setting order
The Language Destination setting order is as follows.
Confirm the indication
on the screen.
Press the “Read” button, “PRODUCT CODE” and “SERIAL No.” will displayed on the screen.
Select the correspond language destination from the pull-down menu, input the “SERIAL No.”, then press the “Write” button.
*1 The “SERIAL No.” is written on the bottom of the camera.
Select the correspond language destination from the pull-down menu, input the “SERIAL No.”, then press the “Write” button.
*1 The “SERIAL No.” is written on the bottom of the camera.
*2 Once the Language Destination setting is finished, it cannot be reset.
The camera restarts and switches to the Mass
Storage connection automatically.
Storage connection automatically.
Disconnect the camera from the dedicated USB
cable and perform the initial setting.
cable and perform the initial setting.
In case of the setting is finished normally,
the setting completion indication appears on
the screen. (Fig. 5-3-40)
the setting completion indication appears on
the screen. (Fig. 5-3-40)
In case of the setting is finished abnormally,
the following message appears on the screen.
(Fig. 5-3-41, 5-3-42)
In this case, perform the setting again upon
the message.
the following message appears on the screen.
(Fig. 5-3-41, 5-3-42)
In this case, perform the setting again upon
the message.
Finished abnormally.
Finished normally.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
DSC-H100_ADJ
5-11E
Selectable language table
DESTINA
TION
AREA
VIDEO OUT
Default
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
Ukrainian
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
EA8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
AU2
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
BR4
BR
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
DSC-H100_ADJ
5-11E
Selectable language table
DESTINA
TION
AREA
VIDEO OUT
Default
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
Ukrainian
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
EA8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
AU2
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
NTSC
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
BR4
BR
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
