DOWNLOAD Sony DSC-H100 / DSC-H200 Service Manual ↓ Size: 3.19 MB | Pages: 17 in PDF or view online for FREE

DSC-H100/H200

1-2

Ref. No:

F2

Part No:

1-576-415-11

Description: FUSE, MICRO (1608 TYPE) (2A/32V)

Ref. No:

F1

Part No:

1-576-415-11

Description: FUSE, MICRO (1608 TYPE) (2A/32V)

The slant of the CCD Block Assy is adjusted with the Lens L Washers, the Lens O Washers and the CCD Rubber 0.5mm in the Lens Block Assy.
After the Lens Block Assy is replaced, select and install the Lens L Washers, the Lens O Washers and the CCD Rubber 0.5mm according to the following.

Screws

CCD Block Assy

Lens Block Assy

Lens O Washers

Lens L Washers

CCD Rubber 0.5mm

Filter Mask

Washer height values A, B, and C are described on the QR Code Label attached to the Lens Block Assy. (A, B, and C show installation positions of  
Lens O Washers.) 
Combinations of these values are grouped into two types: 
The type that uses CCD Rubber 0.5mm and the type that does not use CCD Rubber 0.5mm. Install washers according to the washer installation method 
for each type.

01604750

924

XX

XX

XX

A

B

C

QR Code Label

QR Code Label

Values of Lens O Washers

B

A

C

Lens O Washers

Lens O Washers installation locations

Lens L Washers

1.  Deciding washer installation type

•  Type that uses CCD Rubber 0.5mm

a)  Two values out of three values are 60 or more.

A

B

C

60

65

45

b)  One value out of three values is 80 or more and other two values are between 50 and 60.
 Example)

A

B

C

50

55

80

 

Install washers according to “2. An example of installing washers of the type that uses CCD Rubber 0.5mm.”

•  Type that does not use CCD Rubber 0.5mm

a)  Three values are less than 50.
 Example)

A

B

C

30

25

35

 

Install washers according to “3. An example of installing washers of the type that does not use CCD Rubber 0.5mm.”

 

There are the following types of Lens L Washers and Lens O Washers.

Lens L Type Washer

Part Number

t (mm)

4-447-203-01 0.05

4-447-204-01 0.1

4-447-205-01 0.15

4-447-206-01 0.2

Lens O Type Washer

Part Number 

t (mm)

4-447-208-01 0.05

4-447-209-01 0.1

4-447-211-01 0.15

4-447-212-01

0.2

DSC-H100/H200

1-3E

2.   An example of installing washers of the type that uses CCD Rubber 0.5mm
 Example)

A

B

C

60

65

45

(1)  Install the CCD Rubber 0.5mm and the Filter Mask.
(2)  The minimum value among values at three locations (A, B, and C) is 45. 
 

Therefore, install the following Lens L Washers corresponding to a thickness of 0.45 mm.

 

Lens L Washer (0.2mm) x 2

 

Lens L Washer (0.05mm) x 1

(3)  The value at A is 60 and the difference from the value at C is 15, which corresponds to 0.15 mm. 
 

Therefore, install the following Lens O Washer at location A.

 

Lens O Washer (0.1mm) x 1 

 

Lens O Washer (0.05mm) x 1

(4)  The value at B is 65 and the difference from the value at C is 20, which corresponds to 0.2 mm. 
 

Therefore, install the following Lens O Washer at location B.

 

Lens O Washer (0.1mm) x 2

QR Code Label

01604750

924

60

65

45

A

B

C

A

B

C

Lens O Washer 0.1
(4-447-209-01)

Lens O Washer 0.05
(4-447-208-01)

Lens L Washer 0.2
(4-447-206-01)

Lens L Washer 0.05
(4-447-203-01)

Lens O Washer 0.1
(4-447-209-01)

CCD Rubber 0.5mm

Filter Mask

3.   An example of installing washers of the type that does not use CCD Rubber 0.5mm
 Example)

A

B

C

30

25

35

(1)  Install the Filter Mask.
(2)  The minimum value among values at three locations (A, B, and C) is 25. 
 

Therefore, install the following Lens L Washers corresponding to a thickness of 0.25 mm.

 

Lens L Washer (0.1mm) x 1

 

Lens L Washer (0.15mm) x 1

(3)  The value at A is 30 and the difference from the value at B is 5, which corresponds to 0.05 mm. 
 

Therefore, install the following Lens O Washer at location A.

 

Lens O Washer (0.05mm) x 1

(4)  The value at C is 35 and the difference from the value at B is 10, which corresponds to 0.1 mm. 
 

Therefore, install the following Lens O Washer at location C.

 

Lens O Washer (0.1mm) x 1

QR Code Label

01604750

924

30

25

35

A

B

C

A

B

C

Lens O Washer 0.05
(4-447-208-01)

Lens L Washer 0.1
(4-447-204-01)

Lens L Washer 0.15
(4-447-205-01)

Lens O Washer 0.1
(4-447-209-01)

Filter Mask

DSC-H100/H200

2-1

Follow the disassembly in the numerical order given.

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original one.
•  Items marked “*” are not stocked since they are seldom required for routine service. Some 

delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not supplied.
•  Due to standardization, replacements in the parts list may be different from the parts speci-

fied in the diagrams or the components used on the set.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver) 

: Parts Color

The components identified by mark 

0 or 

dotted line with mark 

0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant 
le numéro spécifié.

When indicating parts by reference 
number, please include the board name.

• Abbreviation
  AUS : Australian model
  BR :  Brazilian model
  CH :   Chinese model
  CND : Canadian model
  RU :  Russian model

Right View

Left View

Front View

Bottom View

Top View

Back View

MAIN

   

• ST Board Assy

   

• Detect SW Board Assy

   

• AF Assist Light Board Assy

DSC-H100/H200

2-2

•  Make sure that the flat cable and flexible board are not cracked of 

bent at the terminal.

  Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, do not pull at wire of connector. It is 

possible that a wire is snapped.

•  When installing a connector, do not press down at wire of connector. 
  It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage 
when the capacitor is handled by hand.  The electric shock 
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned 
off.  Therefore, the remaining voltage must be discharged as 
described below.

To preparing the short jig, a small clip is attached to each end 
of a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

1 k

Ω/1 W

Wrap insulating tape.

1 k

Ω/1 W

Wrap insulating tape.

ST Board

ST Board

R:1 k

Ω/1 W

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.

(Part code: 1-215-869-11)