Sony DSC-G3 (serv.man3) Service Manual ▷ View online
6-32
DSC-G3_ADJ
10MODE screen and functions of each item
1
[Preparation] button
Notes for aging is displayed.
Notes for aging is displayed.
2
Rec Interval setting and display
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
3
Power Off Interval setting and display
The setting of power off interval (min.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
The setting of power off interval (min.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
4
[START] button
The settings of parameters specified by the Rec Interval and
Power Off Interval for execution of 10MODE are sent to the
camera.
The 10MODE starts when the camera power is turned off once
and then on again.
The settings for execution of 10MODE are held until the cam-
era detects the battery end. They cannot be reset by the power
off or RESET button. To interrupt the 10MODE, use the [STOP]
button.
The settings of parameters specified by the Rec Interval and
Power Off Interval for execution of 10MODE are sent to the
camera.
The 10MODE starts when the camera power is turned off once
and then on again.
The settings for execution of 10MODE are held until the cam-
era detects the battery end. They cannot be reset by the power
off or RESET button. To interrupt the 10MODE, use the [STOP]
button.
5
[STOP] button
The settings for execution of 10MODE are reset.
The settings for execution of 10MODE are reset.
6
[GET] button
After the 10MODE was executed, the number of recording
times is got from the counter in the camera. The result is dis-
played in the “Count” display field.
After the 10MODE was executed, the number of recording
times is got from the counter in the camera. The result is dis-
played in the “Count” display field.
7
Count display
The number of recording times got by the [GET] button is dis-
played.
The number of recording times got by the [GET] button is dis-
played.
(2) AGING_REC
In the AGING_REC mode, still pictures are continuously recorded
at the interval (sec.) set to the “Rec Interval”.
At the start of AGING_REC, the counter in the camera is initial-
ized. This counter counts the number of recording times during
the execution of AGING_REC, and it holds the counts even dur-
ing the power off.
at the interval (sec.) set to the “Rec Interval”.
At the start of AGING_REC, the counter in the camera is initial-
ized. This counter counts the number of recording times during
the execution of AGING_REC, and it holds the counts even dur-
ing the power off.
AGING_REC screen and functions of each item
1
[Preparation] button
Notes for aging is displayed.
Notes for aging is displayed.
2
Rec Interval setting and display
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
3
[START] button
The AGING_REC starts. In the AGING_REC mode, the ag-
ing starts immediately when the [START] button is clicked.
At the battery end, the AGING_REC stops. To interrupt the
AGING_REC, use the [STOP] button, though the AGING_REC
stops also by the power off or RESET button.
The AGING_REC starts. In the AGING_REC mode, the ag-
ing starts immediately when the [START] button is clicked.
At the battery end, the AGING_REC stops. To interrupt the
AGING_REC, use the [STOP] button, though the AGING_REC
stops also by the power off or RESET button.
4
[STOP] button
The AGING_REC stops.
The AGING_REC stops.
5
[GET] button
After the AGING_REC was executed, the number of record-
ing times is got from the counter in the camera. The result is
displayed in the “Count” display field.
After the AGING_REC was executed, the number of record-
ing times is got from the counter in the camera. The result is
displayed in the “Count” display field.
6
Count display
The number of recording times got by the [GET] button is dis-
played.
The number of recording times got by the [GET] button is dis-
played.
6
4
5
1
7
2 3
5
3
4
1
6
2
6-33
DSC-G3_ADJ
(3) AGING_MREC
In the AGING_MREC mode, motion pictures are continuously
recorded for the time (sec.) set to the “Rec Time” at the interval
(sec.) set to the “Rec Interval”.
At the start of AGING_MREC, the counter in the camera is ini-
tialized. This counter counts the number of recording times dur-
ing the execution of AGING_MREC, and it holds the counts
even during the power off.
recorded for the time (sec.) set to the “Rec Time” at the interval
(sec.) set to the “Rec Interval”.
At the start of AGING_MREC, the counter in the camera is ini-
tialized. This counter counts the number of recording times dur-
ing the execution of AGING_MREC, and it holds the counts
even during the power off.
AGING_MREC screen and functions of each item
1
[Preparation] button
Notes for aging is displayed.
Notes for aging is displayed.
2
Rec Time setting and display
The setting of recording time (sec.) is displayed. The setting
can be changed by entering a numeric value in this field.
The setting of recording time (sec.) is displayed. The setting
can be changed by entering a numeric value in this field.
3
Rec Interval setting and display
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
The setting of recording interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
4
[START] button
The AGING_MREC starts. In the AGING_MREC mode, the
aging starts immediately when the [START] button is clicked.
At the battery end, the AGING_MREC stops. To interrupt the
AGING_MREC, use the [STOP] button, though the
AGING_MREC stops also by the power off or RESET button.
The AGING_MREC starts. In the AGING_MREC mode, the
aging starts immediately when the [START] button is clicked.
At the battery end, the AGING_MREC stops. To interrupt the
AGING_MREC, use the [STOP] button, though the
AGING_MREC stops also by the power off or RESET button.
5
[STOP] button
The AGING_MREC stops.
The AGING_MREC stops.
6
[GET] button
After the AGING_MREC was executed, the number of record-
ing times is got from the counter in the camera. The result is
displayed in the “Count” display field.
After the AGING_MREC was executed, the number of record-
ing times is got from the counter in the camera. The result is
displayed in the “Count” display field.
7
Count display
The number of recording times got by the [GET] button is dis-
played.
The number of recording times got by the [GET] button is dis-
played.
(4) AGING_PB
In the AGING_PB mode, pictures are continuously played back at
the interval (sec.) set to the “Play Back Interval”.
At the start of AGING_PB, the counter in the camera is initial-
ized. This counter counts the number of play back times during
the execution of AGING_PB, and it holds the counts even during
the power off.
the interval (sec.) set to the “Play Back Interval”.
At the start of AGING_PB, the counter in the camera is initial-
ized. This counter counts the number of play back times during
the execution of AGING_PB, and it holds the counts even during
the power off.
AGING_PB screen and functions of each item
1
[Preparation] button
Notes for aging is displayed.
Notes for aging is displayed.
2
Play Back Interval setting and display
The setting of play back interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
The setting of play back interval (sec.) is displayed. The set-
ting can be changed by entering a numeric value in this field.
3
[START] button
The AGING_PB starts. In the AGING_PB mode, the aging
starts immediately when the [START] button is clicked.
At the battery end, the AGING_PB stops. To interrupt the
AGING_PB, use the [STOP] button, though the AGING_PB
stops also by the power off or RESET button.
The AGING_PB starts. In the AGING_PB mode, the aging
starts immediately when the [START] button is clicked.
At the battery end, the AGING_PB stops. To interrupt the
AGING_PB, use the [STOP] button, though the AGING_PB
stops also by the power off or RESET button.
4
[STOP] button
The AGING_PB stops.
The AGING_PB stops.
5
[GET] button
After the AGING_PB was executed, the number of play back
times is got from the counter in the camera. The result is dis-
played in the “Count” display field.
After the AGING_PB was executed, the number of play back
times is got from the counter in the camera. The result is dis-
played in the “Count” display field.
6
Count display
The number of play back times got by the [GET] button is
displayed.
The number of play back times got by the [GET] button is
displayed.
6
4
5
1
7
2 3
5
3
4
1
6
2
6-34E
DSC-G3_ADJ
2-3.
DATA BACKUP
With the “DATA BACKUP”, the adjustment data in the camera
can be backed up in the PC as a file.
The adjustment data that can be backed up are as follows.
can be backed up in the PC as a file.
The adjustment data that can be backed up are as follows.
System Control Section:
1) Video System Adjustments
2) LCD System Adjustments
1) Video System Adjustments
2) LCD System Adjustments
Camera Control Section:
1) Camera System Adjustments
1) Camera System Adjustments
1.
Function of Each Button on Data Backup Screen
Click the [DATA BACKUP] button on the Main Menu screen, and
the “DATA BACKUP” screen in Fig. 6-2-3 will appear.
the “DATA BACKUP” screen in Fig. 6-2-3 will appear.
Fig. 6-2-3
1
[To Menu] button
Return to the main menu.
Return to the main menu.
2
[Data Read and Save] button
Read the adjustment data from the camera and save them in
PC as a file.
Default file name is as follows:
Read the adjustment data from the camera and save them in
PC as a file.
Default file name is as follows:
3
[Data Load and Write] button
Load the adjustment data from the file saved in PC and write
them to the camera.
Load the adjustment data from the file saved in PC and write
them to the camera.
DSC-G3_ADJBAK_xxxxxxxx_yyyymmdd.dat
Date
USB serial number
Data name
USB serial number
Data name
1
2
3
Revision History
Reverse
DSC-G3_ADJ
Ver.
1.0
1.1
1.2
1.3
Date
2009.01
2009.02
2009.02
2011.06
History
Official Release
Revised-1
(A1 DI08-338)
(A1 DI08-338)
Revised-2
(A2 DI08-358)
(A2 DI08-358)
Revised-3
(A3 11-143)
(A3 11-143)
Contents
—
Replacement of the previously issued SER-
VICE MANUAL 9-852-619-51 with this
Manual.
• Change of Automatic Adjustment Program
VICE MANUAL 9-852-619-51 with this
Manual.
• Change of Automatic Adjustment Program
Version of Automatic Adjustment Program
has been changed from Ver_1.0r01 to
Ver_1.1r02.
has been changed from Ver_1.0r01 to
Ver_1.1r02.
• Automatic Adjustment Program
compatibility on Windows Vista
S.M. revised:
Page 6-2
,
Page 6-3
,
Page 6-4
,
Page 6-8
Replacement of the previously issued SER-
VICE MANUAL 9-852-619-52 with this
Manual.
• Change of Automatic Adjustment Program
VICE MANUAL 9-852-619-52 with this
Manual.
• Change of Automatic Adjustment Program
Version of Automatic Adjustment Program
has been changed from Ver_1.1r02 to
Ver_1.2r03.
has been changed from Ver_1.1r02 to
Ver_1.2r03.
• Addition of Canadian, Hong Kong and
Chinese Models
S.M. revised:
Page 6-8
,
Page 6-10
Replacement of the previously issued SER-
VICE MANUAL 9-852-619-53 with this
Manual.
• Change of Automatic Adjustment Program
VICE MANUAL 9-852-619-53 with this
Manual.
• Change of Automatic Adjustment Program
Version of Automatic Adjustment Program
has been changed from Ver_1.2r03 to
Ver_1.3r04.
has been changed from Ver_1.2r03 to
Ver_1.3r04.
• Correction of Video System Adjustments
S.M. revised:
S.M. revised:
Page 6-8
S.M. Rev.
issued
—
Yes
Yes
Yes
985261954.pdf
