Sony DSC-F88 (serv.man2) Service Manual ▷ View online
1-1
DSC-F88
1-2. DISCHARGING OF THE DC-101
FLEXIBLE BOARD’S CHARGING
CAPACITOR (C014)
CAPACITOR (C014)
The charging capacitor (C014) of the DC-101 flexible board is
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
charged up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of a
resistor of 1 k
resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to prevent
electrical shock.
electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Discharging the Capacitor
Short-circuit between the positive and the negative terminals of
charged capacitor with the short jig about 10 seconds.
charged capacitor with the short jig about 10 seconds.
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
SECTION 1
SERVICE NOTE
DC-101
(CN001)
(CN001)
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
1-2E
DSC-F88
Display Code
1-3. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY
Self-diagnosis display
• C: ss: ss
You can reverse the camera
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
malfunction yourself. (However,
contact your Sony dealer or local
authorized Sony service facility
when you cannot recover from the
camera malfunction.)
• E: ss: ss
Contact your Sony dealer or local
authorized Sony service facility.
authorized Sony service facility.
C:32:ss
C:13:ss
Countermeasure
Turn the power off and on again.
Format the “Memory stick”.
Insert a new “Memory Stick”.
Cause
Trouble with hardware.
Unformatted memory stick is inserted.
Memory stick is broken.
Caution Display During Error
SYSTEM ERROR
FORMAT ERROR
MEMORY STICK ERROR
E:61:ss
E:91:ss
Checking of lens drive circuit.
When failed in the focus and zoom
initialization.
initialization.
Abnormality when flash is being
charged.
charged.
Checking of flash unit or replacement
of flash unit.
of flash unit.
—
DSC-F88
Link
Link
2. DISASSEMBLY
FLEXIBLE BOARDS LOCATION
CIRCUIT BOARDS LOCATION
DISASSEMBLY
SERVICE POSITION
FLEXIBLE BOARDS LOCATION
CIRCUIT BOARDS LOCATION
DISASSEMBLY
SERVICE POSITION
THE METHOD OF ATTACHMENT OF FP-862 AND FP-863 FLEXIBLE BOARDS
HELP
THE METHOD OF ATTACHMENT OF FP-862 AND FP-863 FLEXIBLE BOARDS
HELP
DSC-F88
2. DISASSEMBLY
2. DISASSEMBLY
2-1
2-2
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
SECTION 2
DISASSEMBLY
HELP
HELP
HELP
HELP
to Page 2-3
1
Open the DC lid.
2
Lock ace screw (M1.7)
x2
3
Claw
x4
4
Remove the hinge cover in the
direction of arrow
direction of arrow
A
.
5
Lock ace screw (M1.7)
x5
6
Tapping screw (M1.7)
x2
7
Slide the control switch downward.
8
Claw
x1
9
Rear cabinet
0
Claw
x1
qa
Front cabinet
1
Slit
x1
2
Back light flexible: CN202
3
Slit
x2
4
Claw
x3
5
LCD flexible: CN201
6
Claw
x1
7
Claw
x2
8
Panel block
9
Sheet (T)
0
JK-261 flexible: CN752
qa
Contorol switch (SW) flexible: CN709
qs
DC-101 flexible: CN703
qd
Sheet (T)
qf
harness (hinge assy): CN101
qg
Tapping screws (M1.7)
x2
qh
Claw
x1
qj
FP-882 flexible: CN751
qk
FP-863 flexible: CN102
ql
FP-862 flexible: CN704
w;
SY-099
1
Slide the control switch (mode) upward.
2
Open the BT lid.
3
Claw
x4
4
Claw
x4
5
Control switch (mode)
6
Contorol switch (mode) flexible: CN001
1
Lock ace screw (M1.7)
x1
2
Harness (EA-001)
3
Harness (ST-099): CN001
4
Contorol switch (SW) flexible: CN001
5
Turn the hinge ini the direction of the arrow.
6
Rib
7
Tapping screws (M1.7)
x2
8
Lens section
1
Tapping screws (M1.7)
x1
2
Claw
x1
3
Control switch (SW)
4
Tapping screws (M1.7)
x1
5
DC-101
1
Tapping screws (M1.7)
x2
2
Earth plate
3
JK-261
4
MS connector
4
5
8
3
5
3
4
8
w;
qa
9
1
1
1
0
3
3
A
2
2
3
3
6
0
8
5
7
5
6
6
5
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two
points with the short jig about 10
seconds.
Short-circuit between the two
points with the short jig about 10
seconds.
Note: Disconnection cautions
Remove the harness (hinge assy)
If it draws out directly, there is a possibility of
disconnecting.
Put a thing with a thin tip like tweezers to the
hole of a connector and remove a connector.
If it draws out directly, there is a possibility of
disconnecting.
Put a thing with a thin tip like tweezers to the
hole of a connector and remove a connector.
DC-101
(CN001)
(CN001)
Harness (hinge assy)
Tweezers etc.
4
4
1
2
4
1
1
2
1
2
4
3
6
5
7
9
2 5
3
4 6
7
7
qa
qs
qd
qf
qg
qg
qh
qk
ql
qj
R:1 k
Ω
/1 W
(Part code:
1-215-869-11)
1-215-869-11)
Click on the first or last page to see other DSC-F88 (serv.man2) service manuals if exist.