Sony XR3F-19B160 Service Manual ▷ View online
13
13
XR3F-19B160
2-8.
SCHEMATIC DIAGRAM – MAIN Section –
•
See page 5 for IC Block Diagrams.
(Page
11)
(Page
14)
14
14
2-9.
PRINTED WIRING BOARD – KEY Board –
•
See page 8 for Circuit Boards Location.
2-10. SCHEMATIC DIAGRAM – KEY Board –
•
See page 5 for IC Block Diagram.
XR3F-19B160
(Page 12)
(Page
13)
15
2-11. IC PIN FUNCTION DESCRIPTION
•
MD MAIN BOARD IC601
µ
PD78052GC-123-3B9 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
PH1IN
I
Disc size (8 cm/12 cm) detect signal input from the photosensor (Q604)
“L”: 8 cm, “H”: 12 cm
“L”: 8 cm, “H”: 12 cm
2
PH2OR3
I
Disc in detect signal input from the photosensor (Q605) “H”: disc is present
3
PH4IN
I
Disc loading completion detect signal input from the photosensor (Q607)
“H”: disc loading completed
“H”: disc loading completed
4
AVSS
—
Ground terminal (for analog system)
5
FO
O
Focusing offset automatic alignment signal output to the CXA1782BR (IC501)
6
DAMUTE
O
Muting control signal output to the D/A converter (IC301) “L”: mute on
7
AVREF1
I
Reference voltage input terminal (+5V) (for D/A converter)
8 to 10
—
—
Not used (open)
11
SQIN
I
Subcode Q data input from the CXD2507AQ (IC502)
12
—
—
Not used (open)
13
SQCK
O
Subcode Q data reading clock signal output to the CXD2507AQ (IC502)
14
DAON
O
D/A converter (IC301) power supply on/off control signal output terminal “H”: power on
15
VFINH
O
Inhibit output to the fluorescent indicator tube driver (IC501) “L” active
16
VFLAT
O
Serial data latch pulse output to the fluorescent indicator tube driver (IC501)
17
VFDAT
O
Serial data output to the fluorescent indicator tube driver (IC501)
18
VFCLK
O
Serial data transfer clock signal output to the fluorescent indicator tube driver (IC501) and key
control (IC502)
control (IC502)
19
POWER
O
Main system power supply on/off control signal output terminal “H”: power on
20
SVP
O
Servo system power supply on/off control signal output terminal “H”: power on
21
AMUTE
O
Audio mute on/off control signal output terminal “H”: mute on
22
DMUTE
O
Digital mute on/off control signal output to the CXD2507AQ (IC502) “H”: mute on
23
EECE
O
Not used (open)
24
COMP
O
Analog compression signal output to the SM5852CS (IC302)
25
CDON
O
CD/exit input signal select control signal output to the BA3129F (IC101)
“L”: exit input, “H”: CD on
“L”: exit input, “H”: CD on
26
LGSENS
O
CD logic sense signal output to the external master unit
27
GFS
I
Guard frame sync signal input from the CXD2507AQ (IC502) “L”: NG, “H”: OK
28
FOK
I
Focus OK signal input from the CXD2507AQ (IC502) “L”: NG, “H”: OK
29
APC
O
Laser diode on/off control signal output terminal “L”: laser on
30
EECLK
O
Not used (open)
31
EESO
O
Not used (open)
32
EESI
I
Not used (open)
33
VSS
—
Ground terminal (for digital system)
34
RDS
I
Not used (open)
35 to 39
—
—
Not used (open)
40
SLDON
O
Sledding servo on/off control signal output terminal
41
SEL0
I
Mode selection input terminal (fixed at “L” in this set)
42
SEL1
I
Mode selection input terminal (fixed at “L” in this set)
43
—
—
Not used (open)
44 to 47
ADJOK0 to
ADJOK3
O
Automatic alignment monitor output terminal
Not used (open)
Not used (open)
48
FG0
O
Focusing gain automatic alignment signal output to the CXA1782BR (IC501)
49
FG1
O
Focusing gain automatic alignment signal output to the CXA1782BR (IC501)
16
Pin No.
Pin Name
I/O
Description
50
FGG
O
Focusing gain automatic alignment signal output to the focus coil driver (IC402)
51
—
—
Not used (open)
52
XRST
O
Reset signal output to the SM5852CS (IC302), CXA1782BR (IC501) and CXD2507AQ (IC502)
“L”: reset
“L”: reset
53
DCLK
O
Serial data transfer clock signal output to the CXD2507AQ (IC502)
54
DDATA
O
Serial data output to the CXD2507AQ (IC502)
55
DLAT
O
Serial data latch pulse signal output to the CXD2507AQ (IC502)
56
LMOT1
O
Loading motor (M903) drive signal output terminal *1
57
LMOT2
O
Loading motor (M903) drive signal output terminal *1
58
—
—
Not used (open)
59
IGN
I
Ignition input terminal (connected to power supply in this set)
60
RESET
I
System reset signal input from the reset signal generator (IC602) “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
61
SENS
I
Internal status input from the CXD2507AQ (IC502)
62
RADIOON
I
Radio on/off control signal input from the power connector (CN201)
63
BATTCHK
I
Backup power detection signal input terminal (used also to reset standby)
64
SCOR
I
Subcode sync (S0+S1) detection signal input from the CXD2507AQ (IC502)
65
C.OUT
I
Track number count signal input from the CXA1782BR (IC501)
66
EJKEY
I
Inputs the disc eject switch (S501) detection signal
“L” is input while the switch is pressed (used also to reset standby)
“L” is input while the switch is pressed (used also to reset standby)
67
BATTDET
(INSW)
—
Not used (open)
68
VDD
—
Power supply terminal (+5V) (for digital system)
69
X2
O
Main system clock output terminal (4.19 MHz)
70
X1
I
Main system clock input terminal (4.19 MHz)
71
IC
—
Internal connection terminal (normally connected to ground)
72
—
O
Not used (open)
73
—
I
Not used (fixed at “L”)
74
AVDD
—
Power supply terminal (+5V) (for analog system)
75
AVREF0
I
Reference voltage input terminal (+5V) (for A/D converter)
76
LAMPIN
I
Lamp drive voltage input from the power connector (CN201)
77
SH/LO
O
Shift/load control signal output to the key control (IC502)
78
QH
I
Key data input from the key control (IC502)
79
LSW
I
Inputs the sled limit in detect switch (S301) detection signal
“H”: When the optical pick-up is inner position
“H”: When the optical pick-up is inner position
80
DSW
I
Inputs the disc set detect switch (S601) detection signal
“L”: When completion of the disc chucking operation
“L”: When completion of the disc chucking operation
*1 Loading motor (M903) control
LMOT1 (pin %§)
“H”
“L”
“H”
“L”
LMOT2 (pin %¶)
“H”
“H”
“L”
“L”
Terminal
Operation
OFF
OUT
IN
BRAKE
Click on the first or last page to see other XR3F-19B160 service manuals if exist.