Sony XR-CA660X Service Manual ▷ View online
5
XR-CA660X
Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 20°.
Removing the protection collar
and the bracket (
and the bracket (
4
)
Before installing the unit, remove the
protection collar 5 and the bracket 1 from
the unit.
protection collar 5 and the bracket 1 from
the unit.
1
Remove the protection collar 5.
1 Engage the release keys 7 together with
1 Engage the release keys 7 together with
the protection collar 5.
2 Pull out the release keys 7 to remove the
protection collar 5.
2
Remove the bracket 1.
1 Insert both release keys 7 together
1 Insert both release keys 7 together
between the unit and the bracket 1 until
they click.
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Frequency select switch
(E model)
(E model)
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz
(200 kHz) interval, set the switch on the bottom
of the unit to the 10 k (200 k) position before
making connections.
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz
(200 kHz) interval, set the switch on the bottom
of the unit to the 10 k (200 k) position before
making connections.
Mounting example (
5
)
Installation in the dashboard
Notes
• Bend these Claws outwards for a tight fit, if
• Bend these Claws outwards for a tight fit, if
necessary. (5-2)
• Make sure that the 4 catches on the protection
collar 5 are properly engaged in the slots of the
unit. (5-3)
unit. (5-3)
Mounting the unit in a Japanese
car (
car (
6
)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the supplied
screws 4.
To prevent malfunction, install only with the supplied
screws 4.
How to detach and attach the
front panel (
front panel (
7
)
Before installing the unit, detach the front
panel.
panel.
7
-A
To detach
Before detaching the front panel, be sure to press
(OFF). Press (OPEN), then slide the front panel to
the right side, and pull out the left side.
(OFF). Press (OPEN), then slide the front panel to
the right side, and pull out the left side.
7
-B
To attach
Place the hole A in the front panel onto the spindle
B
B
on the unit as illustrated, then push the left side
in.
Warning when installing in a car
without ACC (accessory) position
on the ignition key switch
without ACC (accessory) position
on the ignition key switch
After turning off the ignition, be sure to
press and hold
press and hold
(OFF)
on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button with
a ballpoint pen, etc., after detaching the front
panel.
completed, be sure to press the RESET button with
a ballpoint pen, etc., after detaching the front
panel.
1
2
2
5
3
182 mm
53 mm
1
1
Fire wall
Panel cortafuegos
Panel cortafuegos
Dashboard
Salpicadero
Salpicadero
5
3
4
1
2
7
5
7
c
c
c
1
Face the hook inwards.
El gancho debe
encontrarse en la parte
interior.
El gancho debe
encontrarse en la parte
interior.
Orient the release key
correctly.
Oriente la llave de
liberación en la dirección
correcta.
correctly.
Oriente la llave de
liberación en la dirección
correcta.
Claws
Uñas
Uñas
6
XR-CA660X
6
A
to dashboard/centre console
al salpicadero/consola central
al salpicadero/consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
B
4
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
TOYOTA
NISSAN
4
to dashboard/centre console
al salpicadero/consola central
al salpicadero/consola central
Bracket
Soporte
Soporte
Bracket
Soporte
Soporte
4
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
max. size
5
5
× 8 mm
Tamaño máx.
5
5
× 8 mm
7
A
B
2
1
c
4
Existing parts supplied with your car
Piezas existentes suministradas con su automóvil
Piezas existentes suministradas con su automóvil
A
B
7
XR-CA660X
SECTION 2
DISASSEMBLY
Note:
Follow the disassembly procedure in the numerical order given.
2-2.
SUB PANEL SECTION
• This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
SET
2-2. SUB PANEL SECTION
(Page 7)
FRONT PANEL SECTION
Note: Illustration of disassembly is omitted.
Note: Illustration of disassembly is omitted.
2-4. MAIN BOARD
(Page 8)
2-3. MECHANISM DECK (MG-25L-136)
(Page 8)
6
two claws
1
screw (PTT2.6
×
6)
2
cover
7
9
sub panel section
3
two screws
(PTT2.6
(PTT2.6
×
6)
8
flexible flat (14core) cable
(CN701)
(CN701)
4
claw
5
claw
8
XR-CA660X
2-4.
MAIN BOARD
2-3.
MECHANISM DECK (MG-25L-136)
3
screw (PTT2.6
×
6)
4
mechanism deck
(MG-25L-136)
(MG-25L-136)
1
flexible board
(CN301)
(CN301)
2
flexible board
(CN351)
(CN351)
1
two screws
(PTT2.6
(PTT2.6
×
6)
3
three ground point
screws
screws
2
two screws
(PTT2.6
(PTT2.6
×
6)
4
rubber cap (25)
5
main board
Click on the first or last page to see other XR-CA660X service manuals if exist.