Sony XR-CA640X Service Manual ▷ View online
12
XR-CA640X
3-3.
ARM (SUCTION)
2
Move the arm (suction) in the arrow
direction and fit on projection.
direction and fit on projection.
1
Fit the arm (suction) on the shaft.
projection
shaft
A
shaft
B
shaft
C
1
Fit the lever (LDG-A) on
shafts
shafts
A
–
C
and install it.
shaft
A
shaft
B
2
Fit the lever (LDG-B) on
shafts
shafts
A
and
B
and
install it.
3
type-E stop ring 2.0
3-4.
LEVER (LDG-A) / (LDG-B)
13
XR-CA640X
3-6.
GUIDE (C)
2
guide (C)
1
three claws
3-5.
GEAR (LDG-FT)
gear (LDG-D)
5
gear (LDG-FT)
6
polyethylene washer
2
tension spring (LD-2)
2
tension spring (LD-1)
gear (LDG-FB)
lever (LDG-A)
hole
hole
4
Align hole in the gear (LDG-D)
with hole the lever (LDG-A).
with hole the lever (LDG-A).
3
Move the lever (LDG-B)
in the arrow direction.
in the arrow direction.
1
14
XR-CA640X
3-7.
MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901)
two precision screws
(P2
(P2
×
2)
Note: Mount the motor so that the
angle between of the
motor and the hole for the
screw becomes 30
motor and the hole for the
screw becomes 30
°
as
shown in this figure.
capstan/reel motor
(M901)
(M901)
30˚
15
XR-CA640X
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the frequency counter becomes 3,000 Hz.
Specification: Constant speed
Adjustment Location:
Tape Speed Adjustment
– SET UPPER VIEW –
SECTION 4
MECHANICAL ADJUSTMENTS
TAPE TENSION MEASUREMENT
1. Clean the following parts with a denatured-alcohol-moistened
swab:
playback head
pinch roller
rubber belt
capstan
idler
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
voltage (14.4 V) unless otherwise noted.
TORQUE MEASUREMENT
Mode
Torque Meter
Meter Reading
2.95 – 6.37 mN•m
Forward
CQ-102C
(30 – 65 g•cm)
(0.42 – 0.90 oz•inch)
Forward
0.05 – 0.44 mN•m
CQ-102C
(0.5 – 4.5g•cm)
Back Tension
(0.01 – 0.06 oz•inch)
2.95 – 6.37 mN•m
Reverse
CQ-102RC
(30 – 65 g•cm)
(0.42 – 0.90 oz•inch)
Reverse
0.05 – 0.44 mN•m
CQ-102RC
(0.5 – 4.5g•cm)
Back Tension
(0.01 – 0.06 oz•inch)
5.89 – 19.61 mN•m
FF, REW
CQ-201B
(60 – 200 g•cm)
(0.83 – 2.78 oz•inch)
Mode
Tension Meter
Meter Reading
Forward
CQ-403A
more than 60 g
(more than 2.12 oz)
Reverse
CQ-403R
more than 60 g
(more than 2.12 oz)
SECTION 5
ELECTRICAL ADJUSTMENTS
0 dB=0.775 V
TAPE SPEED ADJUSTMENT
Setting:
Frequency counter
2,955 to 3,075 Hz
TAPE DECK SECTION
frequency counter
test tape
WS-48A
(3 kHz, 0 dB)
WS-48A
(3 kHz, 0 dB)
set
AUDIO OUT REAR jack (CNJ151)
–
+
10 k
Ω
TUNER SECTION
Tuner section adjustments are done automatically in this set.
Click on the first or last page to see other XR-CA640X service manuals if exist.