DOWNLOAD Sony XR-CA624X Service Manual ↓ Size: 3.01 MB | Pages: 36 in PDF or view online for FREE

5

• This unit is designed for negative earth 12 V

DC operation only.

• Do not get the wires under a screw, or caught

in moving parts (e.g. seat railing).

• Before making connections, disconnect the

earth terminal of the car battery to avoid short
circuits.

• Connect the yellow and red power input leads

only after all other leads have been connected.

• Run all earth wires to a common earth

• Be sure to insulate any loose unconnected

wires with electrical tape for safety.

Notes on the power supply cord (yellow)
• When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

• When no car circuits are rated high enough,

connect the unit directly to the battery.

1)

The numbers in the list are keyed to those in the
instructions.

Handle the bracket 

1 carefully to avoid injuring

your fingers.

2)

Notes (

2-A)

Tip (

2-B-  )

3)

1

To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.

2

To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the

5

To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to it first.

*

*

*

not supplied
非附送
#####

6

1

4

5

2

7

警告

•

本機祇能使用負極接地 12 V 直流電源。

•

不要使導線夾在螺栓下，或繞掛在移動部件上
（如：座椅扶手上）。

•

連接前，先拔去汽車電池的接地端子，以免發生
短路。

•

黃色和紅色電源輸入導線必須在所有其它導線都
連接完畢以後才連接。

•

•

為了安全，請確認把沒有連接的導線用電器膠帶
包紮進行絕緣。

•

將本機與其它立體聲裝置相連接時，所連接的
汽車電路容量必須大於每個裝置保險絲容量的
總和。

•

當汽車電路容量不夠大時，請將本機直接與電
池相連接。

零件一覽表（1）

圖示數字與說明書中的數字是一致的。

拿取裝卸支架 1 時，請特別注意別傷到手指。

線路連接圖例（2）

註（2-A）
• 務必在接放大器之前連接地線。
• 如果您連接了選購件的功率放大器而不使用內置的放

大器，將無報警聲功能。

提示（2-B-

若要連接 2 台或 2 台以上換碟機時，必須使用音源選擇
器 XA-C30（選購件）。

線路連接圖（3）

1

至汽車的金屬表面
首先連接黑色接地導線，然後再連接黃色和紅色電源
輸入導線。

2

至電動天線控制導線或天線升壓放大器的電源導線
註
• 如無電動天線、增壓器或手動操作的伸縮天線，便

不需連接此導線。

• 您的汽車的後玻璃窗中如果有內置 FM/MW/SW 天線，

即請參看“控制和電源線須知”。

3

至選購的功率放大器的 AMP REMOTE IN（放大器遙控
輸入）
本連接僅用於放大器。連接任何其它系統可能會損壞
本機。

4

至在點火鑰匙的輔助位置上通電的 +12 V 電源端子
註
• 若沒有輔助位置，則請連接至常時通電的 +12 V 電

源（電池）端子。
務請首先將黑色接地導線與其連接。

• 您的汽車的後玻璃窗中如果有內置 FM/MW/SW 天線，

即請參看“控制和電源線須知”。

5

至常時都通電的 +12 V 電源端子
務請首先將黑色接地導線與其連接。

•

接通調諧器電源時，電動天線的控制導線（藍色）便
能提供 +12 V 直流電。

•

若您的汽車後玻璃窗上有內置 FM/MW/SW 天線，須將
電動天線控制導線（藍色）或輔助電源輸入導線（紅
色）連接到現有天線放大器上的電源端子上。詳細內
容請向銷售商諮詢。

•

本機不能使用不具備繼電箱的電動天線。

保持記憶的線路連接法
當連接好黃色電源輸入導線時，即使汽車發動機點火鑰匙
被轉在電源切斷之處，電源仍繼續將電流供給記憶用電路，
以保持所記憶著的數據。

•

連接揚聲器電線以前，請先切斷本機電源。

•

使用阻抗為 4-8Ω 且具有充分功率處理容量的揚聲
器，以免損壞揚聲器。

•

不要將揚聲器端子連接到汽車底盤上或將右揚聲器端
子與左揚聲器端子相連接。

•

切勿將本機的接地導線連接至揚聲器的負(-)接線柱。

•

揚聲器不可以並聯連接。

•

請僅連接無源揚聲器。若將有源揚聲器（帶內置放大
器）連接到揚聲器端子上會損壞本機。

3

•This unit is designed for negative earth 12 V

DC operation only.

•Do not get the wires under a screw, or caught

in moving parts (e.g. seat railing).

•Before making connections, disconnect the

earth terminal of the car battery to avoid short
circuits.

•Connect the yellow and red power input leads

only after all other leads have been connected.

•Run all earth wires to a common earth

•Be sure to insulate any loose unconnected

wires with electrical tape for safety.

Notes on the power supply cord (yellow)
•When connecting this unit in combination with

other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.

•When no car circuits are rated high enough,

connect the unit directly to the battery.

1)

The numbers in the list are keyed to those in the
instructions.

Handle the bracket 

1 carefully to avoid injuring

your fingers.

2)

Notes (

2-A)

Tip (

2-B-  )

3)

1

To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.

2

To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there

3

To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.

4

To the +12 V power terminal which is energised
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the

5

To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth to it first.

7

182 mm

53 mm

•Choose the installation location carefully so

that the unit will not interfere with normal
driving operations.

•Avoid installing the unit in areas subject to

dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.

•Use only the supplied mounting hardware for

a safe and secure installation.

•

There must be a distance of at least 15 cm between
the cassette slot of the unit and shift lever in order
to insert a cassette easily. Choose the installation
location carefully so the unit does not interfere
with gear shifting and other driving operations.

15 

cm

Adjust the mounting angle to less than 20°.

4)

4-ATo detach

Before detaching the front panel, be sure to
press 

(OFF). Press (OPEN), then slide the front

panel to the right side, and pull out the left side.

4-B To attach

Place the hole 

 in the front panel onto the

spindle   on the unit as illustrated, then push
the left side in.

5)

6)

You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.

4.

(OFF) on the unit for two

When you press 

(OFF) only momentarily, the

clock display does not turn off and this causes
battery wear.

When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.

2

6

4

5

5

4

4

1

1

5

c

使用前注意事項

• 仔細選擇安裝位置，使之不妨礙正常的駕駛操作。
• 避免將本機放在高溫之處，如陽光直接照射、暖

氣機前、或灰塵極多、髒亂，以及極易受震動等
地方。

• 為使安裝得以安全和可靠，祇能使用提供的安裝

零件。

•在本機的卡帶槽口和變速桿之間，至少需保持

15 cm 距離以便於裝插卡帶。請留心選擇安裝位
置以便使機器不至於妨礙您排檔和其他駕車操
作。

15 

cm

請在 20 °以內調整安裝角度。

如何拆卸和裝配前面板（4）

4-A 拆卸

拆卸前面板之前，須先按下 (OFF) 鍵。然後，按
下 (OPEN) 鍵以便開啟前面板，將前面板稍微向
右邊滑動，然後將前面板的左側拉出。

4-B  裝配

如圖所示，將前面板的 

 孔搭在本機的支軸 

上，然後推入左側。

安裝示例（5）

將本機安裝於日本產汽車上時
（6）

有的日本產汽車不能安裝本機，在這種情形下，請
您向當地的 Sony 經銷商諮詢。

註
為防止發生故障，安裝時只能使用附送的螺絲 4。

安裝在點火鑰匙開關上沒有 ACC
（輔助）位置的汽車上時的警告

(OFF) 兩秒以關掉時鐘顯示。

如果只短暫地按一下 (OFF)，將不會關掉時鐘顯
示而浪費電池。

RESET 按鈕

當安裝和連接完成後，務請用圓珠筆等按壓 RESET
按鈕。

3

8

×

4

×

4

4

×

×

4

•Choose the installation location carefully so

that the unit will not interfere with normal
driving operations.

•Avoid installing the unit in areas subject to

dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.

•Use only the supplied mounting hardware for

a safe and secure installation.

•

There must be a distance of at least 15 cm between
the cassette slot of the unit and shift lever in order
to insert a cassette easily. Choose the installation
location carefully so the unit does not interfere
with gear shifting and other driving operations.

15 

cm

Adjust the mounting angle to less than 20°.

4)

4-ATo detach

Before detaching the front panel, be sure to
press 

(OFF). Press (OPEN), then slide the front

panel to the right side, and pull out the left side.

4-B To attach

Place the hole 

 in the front panel onto the

spindle   on the unit as illustrated, then push
the left side in.

5)

6)

You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.

4.

(OFF) on the unit for two

When you press 

(OFF) only momentarily, the

clock display does not turn off and this causes
battery wear.

When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc.